Tried it but doesn't move with my 6v charger but when I ran it with my drill motor and volt meter it works 2500 rpm 7.5 volts so for a 6v generator we're good. Not sure why it won't spin as a motor? Oh well not important anyway. It charges 👍

Where did you find a draining video? I couldn't even find that... That's it, I'm ripping mine apart and taping everything....

you don't have to polarize an alternator.

How do you do that? I have the same issue and cant figure out how

@@sharkythegw7843 so when u load a video in a row go to the far left and and that box there just click in there and a lock should pop up. That indicates u can’t mess with that row until u unlock again

​@@sneakesview4452 bro every time I move a specific cilp whole vedio timeline resets

@@gamingwitharnav3164 I have been using cap cut for pc works better n easier to use with a shitload of transitions

Yes the exhaust vent gets hot because all the heat from the compressor and back coil unit exit at this point. My unit gets to 114F degrees (45.55C) at the exhaust port on the back of the machine. Window units have the back half hanging outside so you don't feel the heat coming off them. With portable units the whole AC unit is inside so the heat has to be piped to the outside.

Yes I use a fishing weight that I flatten the ends so it doesn't roll away.

@@kennswhatchamacallit9376 ah, gotcha. Thanks 👍

It actually has a continuous drain hose in there! Just gotta remove the plug in it and route it under the bucket. Im gonna go get a longer hose for mine later!

@@sandbucket3245how do you do that?

Do you have more videos on this machine? Like the drain line or cleaning the coils or adding coolant???

On my unit the P1 error is when the draw on the side is not fully pushed in or full of water. If the unit is not cooling as well I would remove the covers to see if there is lint build up on the cooling fins. If you have a large build up of lint covering the fins it will stop air from flowing through the unit and the unit will over heat. If the unit is clean with no lint and not cooling I would have professional check the refrigerant levels in the unit.

@@kennswhatchamacallit9376 thanks Kenn. My unit is connected to outside of my home also so I can have the water go out that way. Could that be a factor as well? It seems the water isn’t exiting that way, but instead building up in the draw and I have to keep emptying the draw

@@matthewhennessy257 I would disconnect the hose and put it into a pan to test whether it's draining through the hose or not. If you let the machine sit to long a spider could build it's nest inside the hose causing a clog, so you need to check for that. I would also test the drain pipe going to the outside of your home. Mud wasps around here like to build there nests in pipes so check yours as it might be clogged. Also if your drain pipe is to narrow you might have to vent it like the way a kitchen or bathroom sink is vented other wise you might be building up a vacuum in the line. Try these things and see if it helps.

Hi yes, in the video at time stamp 3:08 I try to explain if the bottom of the drawer is dirty it needs to be cleaned off. You can us soap and warm water to clean off any build up on the bottom of the drawer and the shelf that it sits on. Then I use Johnson's Past Wax on the bottom of the drawer and the shelf to make everything slide better. The tube does not go inside the pull out drawer it sits on the side and is only used if you have a external drain source. You can see in my video were the tube sits. There is a micro switch that is above the drawer and works off the black plastic float lever that is inside and on the top of the drawer. If the float lever does not move freely then you will have problems. If the micro switch goes bad you will have problems. I would check and make sure these 2 area's are working ok.

You're welcome, I just picked up this portable AC unit but found very few video's on it as well. After figuring out how to take it apart without breaking it I decided to make a video on it to help other people.

​@@kennswhatchamacallit9376any updates on new video of this AC?

Sorry I'm just a novice at this VSDC editor it was the reason I made the video to show VSDC Support Team my problem. I also found that VSDC only does certain things in the free version. Since this video upload, Micro Soft did a update to my Windows 7 OS causing it to say it wasn't Genuine. I tried many things to fix my Windows 7 OS but it wouldn't accept anything, so I moved to Linux Zorin 16 OS. Unfortunately VSDC video editor does not work on Linux, so I went with Kdenlive and Blender.

Yes it is a device that can be used in Paranormal (ghost) investigation to indicate footsteps across a wooden floor. The first one I saw used was in a Ghost Hunter TV show episode .

Do you mean from what I use for the schematic and PCB editor to etching the copper clad board?

All you do is put the positive wire to the switch and from the switch to were the positive wire solders on to the board. It just cuts the power between the battery and the board.

Thank you. I use to be a "B" grade solderer for a electronics company.

Please watch my Building a Rem Pod 2 video kzbin.info/www/bejne/bqm7l3qXhLOihas I try to explain about the 12F508 chip in that video and how to program it.