After watching a lot of vid, how to change motor on tello, this is by far the quickest and easiest. But there are some hacks: 1. Very easy to pull thru the motorcables using another tiny wire or a piece if fishing line as a hook from the other direction 2. Removing the isolation is simplier using a lighter 3 if the cables come out from the leg a tiny bit of glue holds enough and invisible. This black tape is not so nice. Thanks for the vid! 👍
I did this and the replacement motor runs as soon as the battery goes in does anyone know why the motor is running by itself and how I can fix it
@larrymannino4444 жыл бұрын
Hi - just an update: we got the motors and fixed the broken one yesterday. Only replaced the one motor (not the pair), but it worked fine per your splice technique. Just a couple of things to know if you're going to try this: - The wires are really, really tiny! A little tough to strip and twist together. I'd recommend leaving extra room on the new motors wires, just in case, before you pick a point to splice them - Also: feeding the 2 new wires through the hole at the base of the motors mount is also very tricky: the video makes it look easy, but we had to twist them together tights, and work the outside of the hole a little bit to make it slightly larger. - we wound up 'sealing' the splices with tiny pieces of electrical tape; not pretty, but once we wrapped everything up, just fine and the drone is flying once again ;) - One more thing: the 2 wires on the BACK of the rear legs are apparently not for the motors, but instead for aerial reception: leave hem alone. the two wires for the rear motors are stacked on top on each other in the channel int the front part of the leg Otherwise, it all worked, and for a few bucks we got the Tello working, plus it was a fun project to do with my daughter - all good, thanks and good luck!
@xiulanwu6563Ай бұрын
Thanks for the tips, especially the one regarding the extra wires for aerial reception, had I not seen your comment I might have overlook and cut the wrong wires
@ludsat14 жыл бұрын
just curious why you didn't twist inline and solder?
@larrymannino4444 жыл бұрын
I'm new to this but have a Tello with one motor out: Can I replace just ONE motor, or does it have to be done in pairs or (all four)? If someone could let me know, I'd really appreciate it as I need to figure out which kit to order - thanks! Oh, and thanks for the Video!
@onghy4 жыл бұрын
Hi, i just change the motor of my Tello, it's ok to replace 1 motor only, but need to make sure the motor rotating direction is correct. There are 2 types of motor at Tello, CW(blue &black wire) and CCW(white &black wire) Btw this guide really help a lot, I don't have to open the cover and doing the soldering job.
@larrymannino4444 жыл бұрын
@@onghy Thank for your help! May give it a go, though those wires look tiny ;)
@onghy4 жыл бұрын
@@larrymannino444 yes, the wire really tiny, I use a tweezer to handle the wire
@larrymannino4444 жыл бұрын
@@onghy Thanks - ordered some motors - and a magnifying glass ;)
@agrimagu688821 күн бұрын
Can we use cheap and same type of motors in our tello drone..?does it work or not??or maybe doing calibration…!!!
otima ideia o meu esta dando problemas nos motores agora ja sei como resolver . otima dica obrigado
@marcellopezzi5 жыл бұрын
Thanks for the video, very clean and looks easy!
@mychair105 жыл бұрын
Use shrink wrap for a professional finish ok. I think this is the best video on doing this job. Thanks.
@donjarvie21535 жыл бұрын
Its a piece of rubbish,don't get conned like I did,I spent A$ 380 for load of junk for two that I did not want.I got conned into two ,$99 ea. ,plus gst plus,lifetime warranty plus extra props ect. ect.
Very clean way for repairing motors no need to solder thanks
@yone34345 жыл бұрын
Thank you for watching.
@dronepb62385 жыл бұрын
Very good. One question: Is it possible to connect the Tello camera to a sheet video transmitter? Intention: To do FPV with an OTG receiver. Thankful. I've seen the connection of a camera and an external transmitter, never the camera of the Tello to an external transmitter. It's possible?
@yone34345 жыл бұрын
Thank you for watching. I am sorry because I do not understand in detail about your question. Perhaps it is not possible to do it because the frequency band is different from the tello camera.
@indianyoutubers69235 жыл бұрын
prise
@matheusmarcelo49595 жыл бұрын
360 ° ?????
@GoPro2Paintball6 жыл бұрын
This drone is worthless.. don’t waste your money on it. It impossible to control just like any other cheap drones. Very disappointed
@eddrumer6 жыл бұрын
For how long it can be on?
@ZIGOTECH6 жыл бұрын
Hi , it is good. And will you take a look another way of G-sensoer controller? Video: kzbin.info/www/bejne/m6qvhmRteJd7f9k