Hi what's the part number of the gear you replaced on the starter? Great video Very helpful -paul
@LonnieJohnson1Күн бұрын
Try this number - Gear Part# 695708 Also take yours off and match it to a new gear. They sell the gear at Home depot stores or Cub Cadet Dealers. You can find it on Amazon at this link.....www.amazon.com/s?k=Replace+Gear+Part%23+695708&crid=3BW1XSN3POW9L&sprefix=replace+gear+part+695708%2Caps%2C81&ref=nb_sb_noss
@l6j8b323 күн бұрын
I have a yth22/46 and gas keeps pouring into the carb without the motor running. Checked my plugs and they're good, the oil looks good but the engine only starts to turn over. I've been wanting an excuse to buy new but my 10 year old mower was running great before this. A fuel pump and filter is only $13, and a new mower could cost millions.
@l6j8b323 күн бұрын
Correction, I tried to turn my Husqvarna over just now and it works. The gas is in the floor though so I will buy a pump unless there's something I'm missing.
@LonnieJohnson12 күн бұрын
Is there a solenoid on the carburetor?
@l6j8b322 күн бұрын
@@LonnieJohnson1 yes
@LonnieJohnson1Күн бұрын
Make sure it works and is not stuck open.
@l6j8b3223 сағат бұрын
@@LonnieJohnson1 I'm sure thats the problem now but when I saw gas coming out of the pump with the mower not running, I thought, there's my problem. The fuel pump came in today so I'll test the solenoid and maybe change the fuel line this weekend. Thanks for your help.
@jamesbuddy34853 күн бұрын
where did you find spindles i cant find any thanks james
@LonnieJohnson12 күн бұрын
Amazon has them in sets or just one. Check your model #
@KokoBean974 күн бұрын
Thank you!!!! I have a 2005 Chevy Tahoe & someone trying to charge me $65+ to put my part on! I can do this myself.
@LonnieJohnson12 күн бұрын
Your welcome
@matthewschroeter90455 күн бұрын
My set screw won’t go in. Is there a buy or something on the handlebar that the set screw goes into. The one for the housing to slide it off.
@LonnieJohnson12 күн бұрын
It should go in only one way. But you can take it off and see if there is a hole for the set screw.
@matthewschroeter90452 күн бұрын
@@LonnieJohnson1 I took it off there is a hole for it to go into but the screw doesn’t thread in. It’s not stripped because it came out fine and was threaded in.
@LonnieJohnson1Күн бұрын
If it came out it will go back in. You will have to work with it by pushing and turning.
@MrStubat5 күн бұрын
The washers are shims, and come in different micro sizes to get the correct meshing of the gears.
@LonnieJohnson12 күн бұрын
I know there shims and you know that, but people that want to save money by fixing there own equipment know it best as a washer. However, thanks for sharing the info. Just put it back together the same way it came apart.
@MrStubat5 күн бұрын
Just a heads up…..they weren’t washers, they were shims for setting the backlash when reassembling. And they aren’t gears holding the blades, they are splines.
@LonnieJohnson12 күн бұрын
Same reply as before. Thanks
@gabiwenzelow73485 күн бұрын
Thanks for your video. Mine just blew uo while it was running with a loud bang. I could have gotten electrocuted, as I was standing in knee deep level of water, cleaning the pool sides. It could have also Flown in my eye and blinded me if I was standing over it.
@LonnieJohnson12 күн бұрын
Your welcome
@christinep.6 күн бұрын
My Whirlpool water softener worked great for 9 yrs. Then I started getting a lot of white buildup on my plumbing fixtures (faucets, etc.) I had my water softener tank and brine well cleaned and the medium (beads) dumped and replaced with new. Unfortunately, I am still getting the white build up on my faucets 3 months later. The water tests ok (soft) and I have recharged the water softener three times (with cleaner) but it still keeps happening. What is the problem?
@LonnieJohnson12 күн бұрын
Did you do it or did you pay someone to do it. The reason I ask is because you said you had it done.
@christinep.2 күн бұрын
@@LonnieJohnson1 I paid someone to do it. I saw him do it.
@LonnieJohnson1Күн бұрын
What type of resin did he use? was it the recommended resin that's in the manual.
@christinep.Күн бұрын
@@LonnieJohnson1 Yes, I called the manufacturer and confirmed before I purchased it for him
@1981squirrel19816 күн бұрын
Great video. Should one use locktite on bolts or is it enough just to tighten them? :)
@LonnieJohnson12 күн бұрын
Thanks! You don't need loctite because the nuts are very tight. But it's up to you.
@jamalramz78979 күн бұрын
Thanks
@LonnieJohnson12 күн бұрын
Your welcome
@charlesbrewer76699 күн бұрын
I actually have that exact same motor.
@LonnieJohnson12 күн бұрын
Easy motors to work on in my opinion.
@charlesbrewer76699 күн бұрын
Just ran across your video! Thanks for the great tutorial. I had already determined myself to DIY it and your video made me very confident. Now I'm just waiting on the rebuild kit to arrive. I read through comments as well and I believe I'll heed the advice of others and go ahead and change lines out as well. And probably install a filter before the bulb.
@kevinspathelf947111 күн бұрын
I just did the wear ring on mine now I have water pouring into the hull through the one little hole with the o rings on the left while sitting and it sprays in with force like the pumps pushing it when running and floods it? What did I do wrong and what is that hole for?.. 99 seadoo spx 787
@LonnieJohnson12 күн бұрын
It's best to use new o-rings. You have to watch those little o-rings because they will fall out and make for a bad day.
@bennett2112 күн бұрын
The other videos I found for this gear box repair were missing the removal steps. Thank you for your detailed video!
@LonnieJohnson12 күн бұрын
Your welcome
@duncanbecher498613 күн бұрын
How is it running, where is the fuel coming from for it to run
@LonnieJohnson113 күн бұрын
From the gas tank
@bigsnow170514 күн бұрын
Very simple to follow along video. I’ll still call for service to fix mine lol. However 2 summers in a row my carburetor has clogged up and I’m using ethanol free gas. What do you think is the issue?
@LonnieJohnson113 күн бұрын
Cheap gas. You need to run 93 octane
@halamkajohn14 күн бұрын
is there an additional sensor that hooks up to the single terminal.? I dont have an answer. so it maybe sits open , then gets tiny positive from distributor , then grounds coil, then opens? I made a 2 transistor board for a 50 cc AMF moped. buy 1 find out.
@LonnieJohnson113 күн бұрын
You ground by mounting it and then hook up the wire.
@drufreeman590614 күн бұрын
Getting ready to do this on my 2003 Focus with the 2.3L because I have that same code. Replaced the solenoids but they didn’t fix the problem so I’m pretty sure it’s the actuator based on everything I’ve seen and the slight hesitation at low rpm. Otherwise the car has run pretty solid despite this issue. Can’t wait to have my low end power back tho. Thank you for the very instructional video and keeping it simple. I feel I can do this work now on my next days off without worrying about it as much. Having the mental picture of what to do helps me so much. So thank you again for making this video!! You da man!
@LonnieJohnson113 күн бұрын
Your welcome
@andrewpearson341214 күн бұрын
Nice informative video! My dad gave me a Poulan Pro saw that "only needs the fuel line replaced..." to be in working order... It's been a good saw, but has been well used on our farm. The small engine shop charges super high rates to fix anything and they take forever to do it. So I'm going to give it a shot myself. Your video seems to be just what the doctor ordered. I hope it works. Thanks.
@LonnieJohnson113 күн бұрын
Thanks and your welcome
@SylvainFluet15 күн бұрын
Hi from Québec , Canada ! Great tutorial , thank you so much for your help , I need to do the same on my Mercury 90 ELPTO (2006). Your video convinced me to do it myself !
@LonnieJohnson113 күн бұрын
Thanks and your welcome. It looks intimidating but its not that bad. Glad to help.
@SmashixMetal4Evah16 күн бұрын
Thanks Lonnie, I just used this to replace the door and ice funnel on my 17 year old fridge.
@LonnieJohnson113 күн бұрын
Your welcome
@brandonmccall392917 күн бұрын
Whats the part number on the bearings
@LonnieJohnson113 күн бұрын
BEARING (32X58X13) 09262-32023 You can find it on Amazon
@LonnieJohnson113 күн бұрын
Here is a link to parts you might need. www.ronniesmailorder.com/oemparts/a/suz/50d0b166f870022c2c536450/rear-suspension-arm
@michaelfarris255617 күн бұрын
Another fine one
@LonnieJohnson113 күн бұрын
Thanks!
@TheHazelberg18 күн бұрын
Hi Lonnie, i think you provider me here with the solution to my problem. I already changed the Control module in the dash, filled up the freon, checked all fuses and switch, and all are just fine. Just clutch won’t engage on compressor. Now I will check out this low Freon pressure sensor. Thanks a lot 😎👍
@LonnieJohnson113 күн бұрын
Your welcome
@TheHazelberg18 күн бұрын
Hi Lonnie, i think you provider me here with the solution to my problem. I already changed the Control module in the dash, filled up the freon, checked all fuses and switch, and all are just fine. Just clutch won’t engage on compressor. Now I will check out this low Freon pressure sensor. Thanks a lot 😎👍
@TheHazelberg18 күн бұрын
Forgot to mention that I did the test from switch to compressor by bypassing the switch. And the clutch engages then. So.. that traject is fine aswell.
@familyfuntime105618 күн бұрын
Thanks for this video! I did this but now my power steering doesn’t work?! Did I mess something up turning the steering without the mower running?
@LonnieJohnson118 күн бұрын
Your welcome and No you shouldn't have, the steering is separate from the deck belt. Look and check all the connections related to the power steering.
@shadjohnsen814319 күн бұрын
The bow-tie clip at the 1:24 mark is what I've been looking for all day. I could not figure out how it was supposed to attach. Who knew it would use just one hole, on one side instead of the groove on the other side too. Seems like an incomplete design, but if it works it works.
@LonnieJohnson118 күн бұрын
It works but can be a headache.
@mattmcdonald361520 күн бұрын
Man trying to see if i can just tape the wire after the motor caught fire
@LonnieJohnson119 күн бұрын
Black electrical tape should work.
@nayefalkurahi335720 күн бұрын
hey my 2005 seadoo 3d makes a horribke sound when i rev it? like dqueling / brake noise ?? i just replaced the wear ring and filled the cone with 80-90w gear oil.. Prop spins freely.. idk what it could be ?
@LonnieJohnson119 күн бұрын
Where is the sound coming from that you hear? In the back from the pump or from under the seat at the motor.
@nayefalkurahi335719 күн бұрын
@@LonnieJohnson1 hard to tell but seems like from the motor?
Check the drive shaft bearing to see if it needs greased or replaced.
@nayefalkurahi335717 күн бұрын
@@LonnieJohnson1 it looks like it was filled with white lithium, I'll fill it up and see if it goes away..
@DavidGonzalez-pi5hj23 күн бұрын
Excellent video!!! Very clear, very well explained, very easy to understand, thank you so much!!!👍👍👍
@LonnieJohnson119 күн бұрын
Thanks and your welcome
@mikezags081625 күн бұрын
do you think this would be similar in the JX75? where did you purchase the igniter?
@LonnieJohnson125 күн бұрын
Amazon
@LonnieJohnson125 күн бұрын
And yes, I just looked at the JX75 and it looks like the same motor.
@nicholasbourgeois613125 күн бұрын
At the beginning of ur video what is that other plug for
@LonnieJohnson125 күн бұрын
Not sure. Its always been there. Probably for another factory option that wasn't ordered with this SUV.
@TheHazelberg18 күн бұрын
Yes mine has also that plug hanging right there. I always asked myself where it is for. But now I saw it here on yours too. So I don’t think about it anymore.
@nicholasbourgeois613117 күн бұрын
It must not be that important my 2001 doesn't have it really just wish I could get my electric fans to come on
@LonnieJohnson113 күн бұрын
Hook it up straight to the battery to see if it works. If it works it could be a fuse or the sensor. If it don't work it could be a bad fan.
@allenredfearn43825 күн бұрын
Excellent video. Exactly what I needed.
@LonnieJohnson125 күн бұрын
Cool! thanks.
@fredroe755625 күн бұрын
What does that acuator arm hook too its a little white part???
@LonnieJohnson125 күн бұрын
Watch the video at 7:26
@fredroe755625 күн бұрын
@LonnieJohnson1 do you know if that little white ball thing can be purchased? Mine is broken and I'm having no luck around here.
@LonnieJohnson125 күн бұрын
You should be able too. Take the broken part off and take it to an Auto Zone or parts store to match it up.
@fredroe755625 күн бұрын
@LonnieJohnson1 I went to ford dealership yesterday they told me part is obsolete
@LonnieJohnson125 күн бұрын
I would ask what the part is called and try to find an after market part. You can also call around at junk yards to see if they have a vehicle in the their yard like yours and see if it still has the motor in it.
@user-gd2lb5zf5p25 күн бұрын
I've 3 Honda motors, 2 weed eaters and 1 for extensions. All 3 don't stop spinning even without pressing to use. All are under 1 year.
@LonnieJohnson125 күн бұрын
Does the cutting head turn freely when the motor is off?
@user-gd2lb5zf5p25 күн бұрын
@@LonnieJohnson1 it does
@LonnieJohnson125 күн бұрын
Then it could be your idle is too high and needs to be adjusted down lower.
@user-gd2lb5zf5p25 күн бұрын
@@LonnieJohnson1 ok thanks, I will check it today and let you know
@robertwest309326 күн бұрын
You took the fear out of this job for me. Thank you! I was expecting to have to drive the bearings off the whole length of the shaft.
@LonnieJohnson126 күн бұрын
Your welcome
@landen_57628 күн бұрын
i’m getting gas to the fuel pump but not to the carb it had good pressure but it won’t go into the carb
@LonnieJohnson127 күн бұрын
Have you checked your solenoid on the carb.
@CrushingGames28 күн бұрын
Fantastic video!! One of the best! Great Woody the Woodpecker! 🤩
@LonnieJohnson127 күн бұрын
Thanks
@Mel-lp9yz29 күн бұрын
Thank you!!!!
@LonnieJohnson127 күн бұрын
Your welcome
@philorton194029 күн бұрын
Thanks for video. Have the same problem and this helped much!
@LonnieJohnson127 күн бұрын
Your welcome
@user-lh6gg5tl3tАй бұрын
We sell Medium Lift Blade that may fit your equipment. We're happy to offer you the product completely free of charge in exchange for a video review. Let me know if you are interested.
@LonnieJohnson127 күн бұрын
I have an Ex-mark with a 52" cut
@user-lh6gg5tl3t27 күн бұрын
@@LonnieJohnson1 How can we contact you?
@user-lh6gg5tl3t27 күн бұрын
@@LonnieJohnson1 🥳
@LonnieJohnson126 күн бұрын
You want to give me a set of blades if I review and advertise your product.
@user-lh6gg5tl3t23 күн бұрын
@@LonnieJohnson1 Yes.That's right.
@claudesulpizi5787Ай бұрын
Thanks very helpful tips! Doing this same job in a couple of days! Just waiting on the gasket.
@LonnieJohnson127 күн бұрын
Your welcome
@tcaldwell5772Ай бұрын
Is there an edger attachment for this model
@LonnieJohnson1Ай бұрын
Not sure, but I don't think it spins fast enough to be an edger.
@andyzdrums275Ай бұрын
Great video, would this be the exact the same procedure for my 2017 x584? Thanks!
@LonnieJohnson1Ай бұрын
Thanks! It should be close if not the same.
@davidpeterson580Ай бұрын
Finally, this how to video correctly shows how to replace the cable. Luckily I ran across your video before I broke my lawn mower even further. Thanks.
@LonnieJohnson1Ай бұрын
Your welcome
@dadlills4372Ай бұрын
Hey Lonnie I know this an old video but I just tackled my trailboss 330. Couldn't have done it without you. 👌. Turns out the ring clip came off the reverse gear. A very talented mechanic/welder I know made sure that it would never happen again lol. My question is did you replace the triple lip seals on the shafts. Mine look fine but my bud is just change it. Over 100 bucks for the two ughhh. I'm ready to seal it up but holding off now he's got me second guessing lol.
@LonnieJohnson1Ай бұрын
No, not at that price. It should be find if it doesn't look damaged, and if your doing the job yourself you don't have to pay for the cost of labor.
@mckennavandolah745Ай бұрын
Can I get pics or video of all the vacuum and fuel lines? Mine were completely off all lying in a bag when I got my quad and I can’t find anything how they go….
@LonnieJohnson1Ай бұрын
If you start looking at 0:10 you will see the vacuum lines at the top and the gas line is a separate line below those.
@mckennavandolah74528 күн бұрын
@@LonnieJohnson1 mine aren’t hooked up at all…also my choke is unplugged and I can’t find where I plug it into…
@LonnieJohnson127 күн бұрын
Wow! someone left you a real puzzle. I don't have it any more however, what state are you in. Just wondering how close you are, it's easier to look at it and fix it.
@mckennavandolah74520 күн бұрын
@@LonnieJohnson1 I’m in Oregon. I think I have most of it figured out. I can’t find the choke connector from quad to the connector on the electric choke thoufh
@jackswink759Ай бұрын
Excellent, I mean Excellent video!! Put back together, water works but ice lever doesnt work now. Any answers? I figured it out, I put the sleeve in backwards. Great video!
@LonnieJohnson1Ай бұрын
Thanks and thanks.
@allenhughes12Ай бұрын
I have the exact same problem and your video makes me feel a little better about life in general. Thanks for the helpful tips.