Great service

I've seen many countertops your company has done. The only thing that I don't like is the surface on most countertops I've seen you can feel that the surface is not as slick as a epoxy finish

Had this done 3 times to my tub and shower while under warranty. Does not hold up.

This little kzbin.infoUgkxVoi3B4CB6Oygq1-vo4OTL1M_M5JkrXif tub works perfect in our 6 x 6 shower and is easy to get in and out. Also easy to drain.

Excellent

Hai this is Mohammed Sadiq from India I want this product to clean bath tubes at my claint residence many places how to I get this in India

This was a wealth of info.... I love the details how to install a grab bar

Your title is wrong. 2 men talking about a tub and grab bar should be your title not anything to do with installation

How much

Where can i get them chemicals?

What is the name and number of the color used for these countertops?

How much do you charge?

How must you charge?

There was nothing about installing whatsoever, just telling us that these things exist. Wasted my time :(

Hi,Please refer to our site for repairs www.Tamirbazsazi.com

Hi,Please refer to our site for repairs of bath tub www.Tamirbazsazi.com

This doesn't show you how to do anything! It just shows what has already been done.

Look into The SolidMount it is the only designed and patented mounting bracket that was designed just for Fiberglass enclosures. The Solid Mount attaches directly to the studs behind the fiberglass shower and takes all the load off the fiberglass shower. Remember the grab bar is only as solid and safe as the item it is attached to. thesolidmount.com/

he didn't show how to do anything!!!

500 BUCKS??? THAT'S NOT CHEAP THAT'S EXPENSIVE BATHTUB IS 160 PLUS ANOTHER 150 FOR LABOR I RATHER JUST GET IT NEW AND SAVE MONEY

Jesus christ the microphone couldnt be clipping more if you tried!

Waste of my time.Clickbait

4:13 they just finished cleaning the tub and this guy just put that drainage plug on it 🤤

What a lame commercial. NOTHING of value here, especially about installing grab bars. Just a waste of digital space.

All that work you could've replaced.experienced refinisher

It's not a porcelain tub

The grab bar should be rock solid, not give at all.

What a bunch of morons!!!!

do you have locations in Birmingham, alabama?

These videos are good, but not one has addressed the problem of when the wall behind it is an outside concrete wall. I had to find out the hard way on my own. When your wall behind you tile is an outside wall, it will not be a hollow wall, which all these spread apart anchors are made for. No matter how deep you drill, you will not be able to hook up any anchor that has to spread out behind the wall. You have to use plugs, plastic or metal. And make sure the screws are stainless steel, or else they will start rusting in and outside of the wall, with orange seeping down.

I'm in South California and I'm stucco painter, from walls interior/ exterior. I stain and oil cabinetry and also refinish old or ugly bathtubs. I charge $180 labor and material for a bathtub and so on.

So what's the two part cleaners? How do you scuff up the existing gloss finish so the new will adhere?

Amassing part is that someone used it and lived with it :)) must be African Americans :))))

Let me tell you. This company is very expensive. 3 times what I charge. [email protected]

I have a tub resurfacing company. I can't tell you how many of there tubs I had to strip. They skip a critical step in the process.

Bloomington MN area here, I usually refinish just the tub for around 500+ tax.

$500 that's not cheap at all

LIAR !!!! YOU DID NOT SHOWED HOW TO INSTALL GRAB BAR!!!!

LOL this is crap !!!! Buy a new bath for only 200$ ,, or you will pay 300$ for new paint

Nice job but $500 for refinishing, you can buy a NEW tub for $200 and it will outlast the older you one mate.

How much does it cost to refurbish a tub ?

Should have pulled the cabinet to have access to skirt of bathtub. Could have replaced drain too. Not getting silicone off the tub before etching will leave those areas un-etched and could make your coating peel or fish eye. Use a good industrial cleaner to remove all oil / soap from tub surfaces then give the tub a quick wet sanding with 150 grit (to remove any paint spotting or rust stains). Now acid wash tub, rinse and wet sand again. It's ready for an epoxy primer to bond to it. Not using primer is a mistake a lot of guys make to do these tubs fast. Let the primer set up for 30 minutes then apply the top coat in 3 coats (1 flash, 2 burns). Mask off the entire floor with brown paper, 18" around the tub with green paper and plastic sheet off everything else - vacuumed out your room will be like a spray booth. Your tubs will come out smooth with no debris and not needing to be polished. There are coatings out there where you can pull masking, caulk and install fixtures - no going back. They're "Billy approved" too, trust me I try a lot of them. You're right to point ot this is not a DIY job, and is the most toxic thing any tradesman will do in your home. 50% of the tubs I do are re-doing the other guys (failing) job. The best way to reglaze tubs is still old school (acid wash, primer ad top coat).

The coating is as good as the man doing the job! That's a truism in this line of work . The materials will perform as advertised as long as the process is followed. I've used and tested most of them for coming up on 20 years. Very few head scratching results that always eventually taught invaluable lessons. This particular national franchise is considerably further ahead material and tech wise than where it was when the video was shot and currently is by far the industry leader. They simply reinvested in the research and other reputable laboratories instead of lining their pockets. Amazingly after all this time it's awesome to see that they still do the same thing. They put a few people like me to work testing new products and advances for years on end and cross-examined results for accuracy. I've personally done almost exclusively high end residential or large scale commercial projects across the country for the last 15 years that I could easily list on here today so some of you could go see them. They don't force or even try to ask me to say or not say anything that violates my honesty principles. We all work with someone who takes shortcuts...in EVERY line of work. These guys do have a system to quickly identify and correct those issues so even the few mistakes are capitalized on. It makes all the difference in the world if you stand behind your word. If any of you have experienced any adhesion issues then by all means you should require the work be warrantied no matter what company did the job. Working with them while being critical and skeptical, this system is today, to be perfectly honest, almost foolproof. I first got into this industry as a skeptic and fell in love with it because like the military, if you follow the logical process and pay attention to detail it really works well beyond the warranty. Generally people always remember when you do right by them but they never forget when they're lied to or taken advantage of. I've lived with refinished surfaces in my homes from the very beginning and experienced the advancements as they happened. I wish I had the time to start a page to show the capabilities of todays products and processes. Currently their website covers it in pretty good detail. Good luck out there y'all and just remember, do your homework and ask for references. Not some show room somewhere but actual work done. Due diligence! I'll answer any serious questions and go out of my way to help any of you if you really need help. Take care fam!

Really should be wearing a mask dude

man so much hate for a good job... i doubt if most of you can even do this. just admit it, they are pros. I feel good about that job they did. It may be cheaper to purchase a new tub but not cheaper in the end when it comes to plumbing, hauling, labor/re tiling. get real.

The audio is atrocious.

just had my tub done by a company in va.. painters tape pulled the finish off !! guy says its my fault !

Cheaper to just buy a new tub. Tubs on Home Depot website start at 126 bucks. But nice job anyhow.

Hi yer so where do i buy this stuff from please?

What a goofy video why wasn't the tile installed first ?When the tile man gets finished dropping and walking all over that cheap paint finish even if its covered it wont look like crap again .That is a cheap steel tub not a cast iron tub and it flex's and the paint will let go and the rust will come back .