It does come pre-charged, but it's not fully charged. Subscribe, thanx.

You can drive, they are inflated, just not to recommended level (unless the scooter has been sitting in a warehouse for a long time). You can use any pump with a manometer, an electric compressor is optional. Subscribe, thanks.

Don't forget to subscribe, thanx.

Don't forget to subscribe, thanks :)

You need to kick-start it like a regular scooter. The motor kicks in after reaching 3-4 km/h. Subscribe, thanks.

I forgot to say that only shutdowns when i open games or a stress test. 35c to 86c thats crazy.

Is your VGA V341 Ver: 2.1? There wasn't a 1cm thermal pad on mine. Have you changed these thin thermal pads? These temperatures mean the GPU die is not making good contact with the heatsink. Some have noticed that the "Arctic" thermal pads are not squishy enough, and if you use them, the heatsink does not make good contact and the temperature rises sharply. Subscribe, thanks.

Glad to hear it. Don't forget to subscribe. Thanks.

Glad that it was helpful. Don't forget to subscribe, thanks. :)

Thank you for sharing your experience! Is your card Rev 2.0? The thermal pads I measured were the original ones, and yes, they were soft and compressible. In another video (with another graphics card) where I actually replaced the thermal pads, I noticed that some people also had issues with Arctic pads-they seem to be hard and not very compressible. I hope to get more feedback on what size and brand thermal pads people used, this could help make things clearer for everyone. Anyway, don’t forget to subscribe, and thanks again! :)

400€ obuna, rahmat

Good choice, there is no such thing as too much RAM :) Low to medium gaming is definitely possible on this SD7+ gen2. Subscribe, thanks.

@MindaugasJocionis yeah..1week research last I make a decision to buy this pad.y700legion is 1st choice but price is 50% higher.haha.redmi pad pro is support bypass charging also.this features does have at any other redmi pad.correct me if i'm wrong.bypass charging is the priority features I must have,to play game in long session to maintain the battery health

Yes, it has smart charging options. This is useful if you play games and charge at the same time, as this feature will not allow the battery to charge above 80%. In theory, this prevents battery degradation. The Legion Y700 looks good, but it is in a completely different price range.

​@@MindaugasJocionisI saw u play cod using controller.how about the Kay mapping?what apps did u use?and what type of controller?

@ Xbox controller over bluetooth, natively supported.

Check if anything has fallen into it. If not, try resetting it. If the issue persists, send it for an RMA as it's still under warranty. Don't forget to subscribe! Thank you!

€400 subscribe, thanx.

​@@MindaugasJocionisI buy it for 479 euro today

The same QR code is on the scooter base 4:47 (small sticker) and in the manual. Subscribe, thanks.

Purchase the non-MAX version as it's the same SSD but without a heatsink, then choose an enclosure that acts as a heatsink, usually an aluminum enclosure with a thermal pad (the aluminum enclosure acts as a heatsink). Subscribe, thanks.

Your VGA has a different PCB and cooling design. Disassemble it and measure the thickness of the thermal pads on your unit. Subscribe, thanks.

@MindaugasJocionis ok thanks

did you find any other good option for the price?

Nice, don't forget to subscribe, thanks :)

same bra

@@robinson158 This voice wasn't supposed to be sexy, it was supposed to be understandable. :) Anyway sub. thx.

¿No se enciende en absoluto o el motor simplemente no gira? Suscríbete, gracias.

These are not errors. You are entering unique values from your camera's BIOS dump into the downloaded BIOS from the internet, such as your MAC address, unique ID, and the language the camera will use. The camera should work even with an unmodified downloaded BIOS. I'm not sure why you can read but cannot erase your BIOS chip. Try searching online for solutions. As for the LEDs, it's probably just a slightly different design of the programmer. Don't forget to subscribe-thanks!

My ISP does not use authentication, so I cannot check it for you. I would try to set up PPPoE with the wizard. (In Quick internet setup wizard, bellow "create a new network" there is advanced settings option. Use this to walk you through setup) If that doesn't help, reach out to your ISP. They might have some additional configuration settings that need to be entered. Also, double-check your cables from the fiber optics box to the router. On the Router side, the LAN cable must be connected to the WAN port. Subscribe, thanks.

I believe it shows 100%, but newer pay attention to that. Usually, I charge the scooter in the off state. When the charger light turns green, it means it's fully charged. Subscribe, thanks.

@MindaugasJocionis thanks (:

Don't forget to subscribe, thanx :)

Yup 👍

In summer l ride everywhere with it. Definitely worth having one. Subscribe, thanks

Legal, não esqueça de se inscrever, obrigado ♡

With my PSU high speed RPM does not kick in, so it should be good. With this case, you'll need a good PSU since it will be drawing in hot air. Cheaper models might become noisy as they struggle to handle high temperatures while operating in low RPM mode. Subscribe, thanks.

@ I have a Chieftec PowerPlay Gold 650W power supply.

This is a decent power supply, and you shouldn't encounter any issues with it. For optimal efficiency, aim for your hardware to draw approximately 50% of the PSU's maximum power capacity.

A little later I changed the fans to RGB, added one fan in the front, and switched the rear one to exhaust :) In general, everything is as you described :) Subscribe, thank you.

kzbin.infoUgkxi9OcDieuaJHNEOsgBL_ygFIwMhxxeXN-?si=LWVbxfGJylxDQOtU

You need to disassemble the handlebar and dashboard a bit more. Check KZbin-there are plenty of videos showing how to do it. Don’t forget to subscribe. Thanks! kzbin.info/www/bejne/j3fWZ2unfLWCocUsi=YFtRUx84mJtqgg39

@@vladyslavm7316 The thermals remain the same, but the boost clocks have returned to the levels they were at when the card was new. That's how GPUs work these days-they push frequencies until a certain temperature is reached. Subscribe, thanks.

@MindaugasJocionis Thanks for the answer! The thing is that I recently bought a used 2060 serviced. Temperature 80-83 on the chip. I just wondered if the temperatures would drop after applying mx-6.

@@vladyslavm7316 @vladyslavm7316 What are your GPU speeds at this temperature in games? What is your card model? Is your case big with decent airflow, or is it a small ITX case with limited airflow?

You need to kick-start it like a regular scooter. The motor kicks in after reaching 3-4 km/h. Subscribe, thanks.

Yes, connect your modem lan cable to asus router, then in operation mode choose Access point mode. Subscribe, thanks.

Thank you ❤️❤️❤️, and don't forget to subscribe :)

Yes, they are inflated, just not to the recommended level. You can drive with them for some time. Subscribe, thanks.

​@@MindaugasJocionisoh got it! Thx!!

@@Johnlockev2 This list indicates that the processor is physically compatible with the socket, but whether it will work is hard to say for certain. You need a CPU with the same TDP as your original one or the best CPU officially supported by your motherboard, as its VRM is designed for that specific power consumption. Additionally, it depends on whether your BIOS supports the CPU model. I haven’t tried a CPU swap myself, so I can’t guarantee it will work. You’ll need to try it out on your own. Don’t forget to share your results-successful or not-as it could help others. Subscribe, and thanks!

@MindaugasJocionis brother pls last help can you suggest me which one will be the best to try cause I will soon visit the technician I live in india if you have a suggestion please give me I researched high but didn't clie pls suggest any i7 3rd gen that probably have the most likely chance to work 😭😭😭😭😭

Honestly, I don't know, try searching on KZbin, for example: kzbin.info/www/bejne/qGaxfpqJYsd7mJosi=fwTUBgGuqhYtja82

@@khderkhdora6514 Thank you very much and don't forget to subscribe ❤

@@MindaugasJocionis Yes I'm subscribe to you

@@Carljhonson6969 Nice, don't forget to subscribe, thanks.

You need to kick-start it like a regular scooter. The motor kicks in after reaching 3-4 km/h. Subscribe, thanks.

@@MindaugasJocionis Thank you a lot!

In this case, the controller was stuck due to the use of a third-party app. Similar behavior may occur after water damage or flashing incorrect firmware; in such cases, this method won't fix a problem. Subscribe, thanks

In your country, electric scooters are probably limited to 20 km/h. It's locked in firmware. Here is link to the guide: dnandha.github.io/stlink-lks32/ I haven't tried it myself, as mine is designed for 25 km/h region out of the box.

It's a tire inflation reminder triggered by a time interval, just don't worry about that. Or try rebooting your phone and scooter might be after that it will appear. Don't forget to subscribe. Thanks!

@@mrovi7711 If this issue happened unexpectedly (not due to drv flashing or using certain apps), it’s likely caused by water damage. Disconnect and disassemble the dashboard, then clean the PCB with isopropyl alcohol. If that doesn’t resolve the problem, disassemble the button as well and clean it. Don’t forget to subscribe. Thanks!

A regular USB extension cable. Subscribe, thank you.

No, subscribe, thanks.

Try a better screwdriver, or buy screw removal set. Check this video: kzbin.info/www/bejne/hprYe3Zvm9ysmcksi=jA1lEUtWPqlE0cs1 Subscribe, thanks.