Does anyone do where to get those clips or what's they are called trying to look dor them but no luck

I have this same hoist wish I knew what part #s you had.

Thank you ❤

I'm getting dizzy

If you get a tool with a tiny spike on the end of it you can quite easily get underneath the little plastic catch and pull it towards the rest of the cap, comes off easy.

Could you tell me if there are 2 x steel balls at the base of the pump? I did retrieve one from in there and found one more on the floor!

I got upset and broke the damn thing off haha its just a plug anyway you can just stick it back in. fuck that clip

I ended up taking the battery tray off. Once I removed this awful thing I deliberately snapped off the tang. The next time I can just reach in grab the bung and lift it out. No more plastic clip.

thanks

It’s a good video but for 37.00 I bought a whole new hydraulic pump. How much were the seals? 10-15 bucks. What is your time worth?

I'm going crazy. I still can't get it off. I feel like I have to. I have more muscle

Thank you very much! This helped me get the ball join boot clip on. One extra tip: If it stil goes difficult with the tie wrap, then only put the tie wraps on the bottom ring of the clip. Then you can put that on first, and put the rest of the clip on by going around the clip with the tie wraps.

It says a year ago….? I just got flashback to my cat also getting stolen from my Lancer 2015 back in June on 2023 But ill love some help .. what is the website were did you purchase the cat.? Im on NY and impossible to get a cat for my car. Is a MITSU 2015 ES 2.0 CALI emission LEV. USA EPA

Dude. This has LITERALLY changed my life. Amazing!

This might be the worst connector I've ever dealt with

Who rebuilt it Charley Chaplin no voice i instructions

Also, can you please send a link of where you bought this from. My wife is pregnant, baby comes soon, we need the car working fast.

Hi, please if you’re reading this, I really need help. Mine is an RVR 2020 2.0L. From this video, it means the 2013-2018 one can work if I get it right? Mine stolen as well. But they cut off both the upstream O2. The same length as the new one you got in this video.

Will this fit 2015 RVR? It looks almost identical.

Next time please show the valve dowel position

You are a rockstar for this bro 💪

Thank you 🎉🎉🎉🎉🎉)

Silly question - could you not have stacked two of the 5mm seals to make up a 10mm seal with two lips? That way if one failed the second would hold too?

Great video thank you. Very helpful.

Emery paper would be better

you must be america's skinniest man

Where did you get the parts diagram?

Great work ….Excellant Job

MASTERFULLY DONE!!!!! YOU SAVED ME MUCH TROUBLE!!!!!!

Worked a treat. Many thanks from West Yorkshire in the UK.

What is the name of the seal at the bottom that you didn’t replace? Mine was broken and I need to change it. And what’s the name of the local shop you bought your kit from? I would like to use your measurements to rebuild mines. This will be my first time doing so and I wouldn’t know what parts to ask for. Our cylinders look identical.

I'm not sure what you're replacing. My 2016 Outlander supposedly has the catalytic converter integrated with the exhaust manifold.

🙏🏼🌹🌺♥️🌸🌼🇨🇦🌻❤️🙏🏼

I am looking to replace my cat as well. A shop wanted to charge me 4500 for everything. They also wanted to chage me $600 for spark plugs and $300 to charge the spark plugs

I can’t get the strap on the bolts are already all the way out and still can’t get it to hold up I am using wire right now why

You don't fill the CVT from that tube so there is no reason to remove it. The fluid is serviced through the drain plug. There is a standpipe in the drain hole and you use an adapter that screws into that standpipe then you pump fluid in and the service manual states the initial amount of fluid to put in. Then you start the car and warm up the CVT to the specified temp then you pump about half liter of fluid in and then remove the adapter and let the fluid drain out. It will stop draining when the fluid is level with the standpipe and the CVT is now properly serviced. Checking service is done the same way you just pump fluid in through drain port staring with about half liter at a time until it starts to drain and then you wait until it stops and the level is good.

You are the best ever. Thank you.

... Realizes he forgot the grease, has to repeat. Glad he didn't close the zip ties. 😁

After an hour of failing to get the cap off and other videos not helping...I finally did it after watching your video! Thank you. It was your close up of the inside clip on the cap that was most helpful in enabling me to visualize what needed to be done.

Just tried your technique. Worked great. Much easier than other ways I have tried. Thank you.

Wonder does p0420 or other emission engine codes thrown? replaced mine with a high flow cat from a local muffler shop. Now it throws the code every 500km :(

Thank you for posting up bro, very informative, very helpful.

Did this part from green exhaust keep the cel off? does your car say federal and California emissions under the hood on the sticker? I replaced mine with ebay cheap $45 part that said it fit 2011-2012 it looks like same shape it fits says epa compliant but got cel on p0420. my car sticker says federal and California emissions compliant. I don't live in California but wonder if this is the problem that my cel is on. I bought car also it had universal cat welded on got p0420 occasionally. I did what I said above to fix it "better" The part I bought made cel on all the time. I replaced both o2 sensors as well. Also from ebay for $43. I see mitsubishi has intermediate pipe for about $2155 but if there is cars with just federal emissions they should have two to choose from if the car can be bought with federal and California emissions or with just federal emissions.

Is the piston integrated with the rod?

Did it pass emission test? If yes what state? Just contacted that eBay seller for my car is 2012 outlander 2.4

Grease it first

Finally a well explained video omg that thing to get off is horrible 😂

You made it look easy! I have a 2013 and mine didn't get stolen but it's bad and needs replaced😢. I wish someone would steal it cause it's fully insured lol

Thanks a million, man. I almost had it figured, but was about to give up for the night. I googled, and someone had put your KZbin link up. I had already watched an infinite number of diy tutorials, but none had covered this part on this model. It is sort of the opposite of the other Nissans. Maybe that's why they called it "Versa". I made some room to work it by removing that air intake, the battery, the sensor/harness in front of it (without disconnecting), and the coolant overflow (also without disconnecting). 15 minutes work, and only a handful of bolts (fingers for the hose clamp, a 1/2 for the battery tiedown, and 10mm for everything else). I used an eyeglasses screwdriver and my hand to pull the plug. Oh, well. I hope my overdue service goes without glitches tomorrow. Thanks again. Keep it up!

Good job!