@@colinhunter9170 it's been excellent, heals well and had no issues with sisal hairs breaking up, very pleased buddy👍🏽

@@legacyo16 I'll measure it and do the math, then come back to you in a couple of hours or so, I'm not home at the minute but as soon as I get home I'll have a look and message you back

Hi again. So I've measured the door hanger and the maximum height of a door to hang it on is Aprox 207cm by the looks of it. The cross member that the darts board hangs on can be adjusted up & down a slider, which is held into position with 2 screws that you tighten up to lock it in place but the slots for the screws in the slider are only 10 cm long. My door is 196 & there is only 7cm's of the slider left for manoeuvring the cross member further down the slider unfortunately, so to get the bull at 173cm at the lowest slider setting, the hook of the holder would be at about 207/208 I'm afraid to say

Ah damn. That’s a pain. Thank you anyways!! I could probably drill the hole into the board a bit higher and that should fix the issue or?

@@legacyo16 the only problem with that is when it comes to rotating the board, it would mean putting a new hole each time, but in theory it would work, you just might need to put some wedges behind the other areas of the back of the board to make sure it sits level from top to bottom👍🏼

👍🏼 it was to start with but there is about an inch gap behind the hanger once it's up on the door, so I put sponge behind the feet positions & it's made it very quiet now👍🏼

Sorry only just seen this. So far it's been excellent, it hasn't marked up much at all, it's soft and heals well so no issues with marking, hope that helps 👍🏼

It comes with 3 little rubber feet that push in to pre drilled holes in the back of the board, as well as the mounting kit. The holes are roughly at the back of the numbers 4/3/9 . Hope that helps 👍🏼

Hiya David, hope you're well buddy, I'm ok thanks for asking, good to hear from you. Been a tough time my friend, at my parents most weekends at the moment still, but fingers crossed that will change at some point soon & I can start having darts weekends again, I miss our group on discord very much, but I just can't plan anything for weekends at the moment unfortunately 😕

Cheers dude, yeh I'm impressed looks fab

I haven't noticed to be honest as mine is hanging on a door hanger, on the back of a door but yeah that does make sense actually. I put a couple of pieces of sponge behind mine too, not sure how much sound difference it has made though if I'm honest. Thanks for your comment & great point, thanks for sharing👍🏼

Thanks 👍

You could possibly make your own hanger bracket, it's only 1 screw that screws down from the hanger bracket to the frame of the hanger so perhaps you could make one for any type of door frame I would think.

Probably the camera, it looked ok once up in the surround, well I think it did anyway lol

@@tommyboyle23 I live right next to datadart so picked up one of their boards. Honestly it's holding up just as well as my blade 6 ever did

👍🏼 hi there, sorry I've only just seen these messages. I got the pads off eBay, their double sided heavy duty pads, but obviously I left one side of the pads with the peel paper still on so it didn't stick to door or dartboard. Hope that helps 👍🏼

Wow that's expensive buddy, darts corner in the UK ship world wide but honestly I don't know what it would cost in terms of import taxes for you but I do know that as it's beeping shipped abroad they remove the English value added tax or VAT so you do get 20% off the retail price but obviously then the postal cost and import tax could well make it expensive, but certainly worth contacting them

Great comment thank you buddy 👍🏼

Cheers buddy, bit long winded but nature of the beast I guess 😂

Hey met buddy hope your well. Back live streaming on the 26th mate for the players masters see you over on discord then fella👍🏻

i'm not actually sure and it doesn't say anywhere but i've asked Target the question so just waiting on a reply, thanks Tommy

So Target have been in touch and they have said the darts are front weighted.👍🏻

Unfortunately not there's a Judas jealous youtuber that keeps reporting me. Send me an email at [email protected], I can give you an alternative 👍🏻

couldn’t have said it better myself

Hi buddy. In theory you could pull the mount all the way forward so the board would slide up higher than it but then where the mount clamps over the top and comes down on the other side of the door,there would Aprox 15mm gap between the door and the clamp, but worth experimenting with a small block of wood between door and clamp to see if it works. Have you got an email where I could perhaps send you a couple of pics or something to explain what I mean with a short video or some pictures to make it more sense. I've not actually tried it myself, this way but in theory it should work.👍🏻