Streamline Builds

Пікірлер

@arfrce72 Күн бұрын

So you used the CPP spindles with the Ride tech truturn kit. I have a 69 firebird and am having the same issue with not being able to run a wide wheel.

@streamlinebuilds1490 19 сағат бұрын

Yes I would actually not recommend the ride tech truturn as it was seeming to bind up a little bit and I needed to do some grinding, I would go with a rack n pinion.

@recoswift6390 5 күн бұрын

You should have put that on a press.

@streamlinebuilds1490 19 сағат бұрын

It would be nice if I had one for sure. Need a bigger shop and more tools one day lol

@bobodean1 8 күн бұрын

Wow....how much coffee did you drink before this?

@streamlinebuilds1490 19 сағат бұрын

Haha

@backspace4093 10 күн бұрын

Did you ever get around to restoring this car.

@SesameStreetRacingChannel 13 күн бұрын

Do you have any regrets about not buying this car...now that it is 5 years later?...That engine sounds good...but the whole deal was "crusty".

@ReneShark 17 күн бұрын

What is the other actuator that is by the blower motor. I get no air out of the defroster

@TaraMacNeil Ай бұрын

Great video man, very helpful!

@thatguy5358 2 ай бұрын

be a lot cooler if you showed exactly how it was wired up...

@jamesquinnie7573 2 ай бұрын

Awesome Great Video ❤🔥👏👌👍🏻

@jamesquinnie7573 2 ай бұрын

Where can i buy the tool to change the bolt pattern from??

@KenTibbetts 2 ай бұрын

5:56 hahaha. ive felt the same way. i swear that they do it so u have to bring it to a shop… for most people

@AsianBlackR3501 3 ай бұрын

I saw someone did it with special thin tool to replace the belt without remove any parts except the side fender without one wheel removed.

@rvelarde23 3 ай бұрын

Great video, I’ve been meaning to change my belt and water pump (seems like it’s not working 100%) the heating gauge is always above the half mark closer to the 3/4 not sure if that’s normal on this engine

@streamlinebuilds1490 2 ай бұрын

Yeah sounds like it's getting too hot unless the gauge or sender is actually the culprit

@mymodestgarage9211 3 ай бұрын

Wish you’d show the final product on this and the trans swap.

@cjinmichigan 3 ай бұрын

Thats the exact noise mine is making . Out 190,000

@PeterHatch-mx7zc 3 ай бұрын

Just sub up thks for the video and that tool👍

@gottoogogaming8096 3 ай бұрын

Thats gotta be an illegal swap.

@ekbanjosworld4926 4 ай бұрын

Spring Compressor ! You need to try climbing up in the engine bay or just even crawling around down underneath when you're 62+ ! FUN !

@Professional_ProCraftinator 4 ай бұрын

Can you please tell me which part needs replaced if our 2015 Silverado 2500 HD truck's HVAC vents sometimes gets stuck blowing only up to the defrost vemts, even when we have pressed the setting to blow air straight out of dash, towards our faces. To clarify, I am asking what that replacement part is called and where that part was located in the truck. Was it the part locted behind glove box or the part above the accelerator? Thank you in advance!

@streamlinebuilds1490 3 ай бұрын

Hi I believe this would be your blend door actuator, however the issue is there are more than one and to identify which one it is you would need to gain access and adjust controls to see if they are moving or stuck. That's the best advice I can offer

@StarknightMT_official 4 ай бұрын

Hello, Are you interested in testing our products? We would like to invite you to test the Light Tint Rear Windshield for your RZR 800 (if your car year is 2009-2014

@RAWRMotorsports 4 ай бұрын

Part#

@streamlinebuilds1490 4 ай бұрын

Sorry I should've put in the description it's been a long while now but I did buy off eBay making sure it looked identical to my old one

@nagromotf8365 5 ай бұрын

Can I get one 4x100 to 5x114.3 ??? Where I can buy it?

@streamlinebuilds1490 5 ай бұрын

Link is in the description and in the video

@phillipswantek7494 5 ай бұрын

nesselhauf is right. I have viewed a dozen of these to glean as much info as possible. You put impeller in clockwise which is wrong. It is to be put in spinning counter clockwise. Fortunately for you the shaft spun it in to place in the counterclockwise position. If you are viewing this for information. Put the impeller in so it turns counterclockwise. Obviously when installed it will turn clockwise as you look at it from the side that will be facing up. When you take your old one out, notice the orientation. However, if really old, some of the fins may be flipped and facing the wrong way.

@charliedaubitz2046 5 ай бұрын

25 ftlbs will snap those impeller 1/4" bolts off

@Shanonmcnab576 6 ай бұрын

Easier just to remove sway bar. Might as well change the sway bars while a persons at it anyway.

@johnhammond2390 6 ай бұрын

Where did you get that wondering if I can do that to make truck

@swfloridacarguy1987 6 ай бұрын

Keep up the good work!

@stevenlewisonair8298 6 ай бұрын

How did you get the nut on the top of the slave loose? The one with no clearance, facing the line?

@simple8777 6 ай бұрын

How many boxes did you need?

@Zyxalis 6 ай бұрын

Thanks for the vid, it helped me today!

@troywright7046 6 ай бұрын

Nice truck to fix up

@CHRISCRAZZ-t7w 6 ай бұрын

Skills to pay the bills

@thefreckledmom 6 ай бұрын

Nothing like the good ol' Engineer okie doke! Lol

@sonofthunders1105 7 ай бұрын

Nice job! Think I will leave it to an expert. 😁

@sorchacostigan3725 7 ай бұрын

Did you have to pull the transmission all the way off to get to the TOB?

@jameskirk5906 7 ай бұрын

Rough but nice! MAGA 2024!!!

@opiethrice8746 7 ай бұрын

The idle sound with no clutch engagement is the exact sound my 1997 tj is making at the moment. Looks like this weekends project!!

@annabellendad 7 ай бұрын

What's available from left over parts? Can you message me

@streamlinebuilds1490 7 ай бұрын

I'm thinking all the removed parts are already gone sorry.

@angeloplanes8497 7 ай бұрын

The passenger front slides forward. The driver side wouldn’t make sense with steering wheel limiting the slide/fold function.

@austindoehling887 7 ай бұрын

Relocating the upper arm with that mod works great. Glues the car to the road.

@matthewryan7765 7 ай бұрын

Lol you tried to install that break clip upside down 😂

@CesarCano-e7x 8 ай бұрын

I want to do that to my Chevrolet Silverado , 2wd , from 5 lug nut pattern to 6 lug nut pattern , for Chevy 6 lug wheels .

@justlistening9463 8 ай бұрын

Good find id take it do respecable resto mod's to like c6 zo6 motor trans keeping same factory colors be super Z28 / RS.SS hot rod 💪 😎