9 ай бұрын
2 жыл бұрын
3 жыл бұрын
4 жыл бұрын
Пікірлер
@goon3145 6 ай бұрын
Is it the same location for sensor on 2006 Lexus gs430
@SpiKSpaN-ei6zq 7 ай бұрын
Who sell replacement transmission thats reliable??
@adnana.shahban4151 11 ай бұрын
Whats the recommended milage to change this ? Or just drive and wait when its faulty then change ?
@danielx7922 9 ай бұрын
I'm sorry but I don't don't the recommend mileage. But the usually last 100k miles. The valve should only allow air flow through 1 one direction. So if you can blow air through both holes then it's bad
@aros007z Жыл бұрын
Awesomeness
@Nostradamus_Order33 Жыл бұрын
Just give him twenty bucks to pass. That’s all they want anyway.
@gianvmarco Жыл бұрын
unplug battery easier lol
@danielx7922 Жыл бұрын
No. That doesn't work brother, everytime you unplug the battery you reset the parameters so if you got 12 warm ups done you have to start from 0
@Nostradamus_Order33 Жыл бұрын
@@danielx7922 you have to drain the power to the computer. Unplug for 24 hours.
@TK-jj9xr Жыл бұрын
@@Nostradamus_Order33 that doesn't work for permanent dtc codes for cars 2010+
@ronaldreagan388 7 ай бұрын
@@Nostradamus_Order33you can't disconnect the battery, trust me... we replaced a engine on a malibu therefore the battery was disconnect for a couple of months, from the time it took to find an engine and install it... and permanent code was still in the system after pluging it and turning it on.
@stevew9563 Жыл бұрын
One correction to your Video. The 15 warm up cycles (not drive cycles) and 200 miles driven won't "Clear" the Permanent DTC. When you get the 15/200 the CA SMOG machine will "Ignore" the permanent DTC. Now you may clear it in the 15/200 but if you have not no need to worry as long as you got the 15/200 you will pass the SMOG as long as no other cods have come up and gone to a confirmed code. More info here: www.bar.ca.gov/Industry/PDTC
@Theo-SeriesFanatic-fv6sg Жыл бұрын
The only video I could find .. even though .. it’s not the best it’s something thanks
@jonathanwhite7968 2 жыл бұрын
So 15 cold warm ups an plus 200 miles after right
@danielx7922 Жыл бұрын
Yeah. Sorry for the late reply I didn't see you notification
@bam-bo 2 жыл бұрын
hey did you have to disconnect your radiator hose to get the starter out? if so, was there fluid in there and how did you do that?
@danielx7922 2 жыл бұрын
No you don't have disconnect the upper radiator hose. You can get to it from the bottom. The Starter is protected or hidden by a heat Shield.
@bam-bo 2 жыл бұрын
@@danielx7922 ah i see. you raised your car and removed the starter from under the car? I think i may do that instead of having to remove a bunch of stuff from the top.
@danielx7922 2 жыл бұрын
@@bam-bo Yeah. I try to skip steps of the procedure to make the videos shorter but thank you. I'll add more info next time
@bam-bo 2 жыл бұрын
@@danielx7922 Thank you Daniel! I am going to give this a try on my cadenza this weekend. Let you know how it goes.
@danielx7922 2 жыл бұрын
@@bam-bo if you get stuck let me know but it's not hard. The only hard part is removing the heat shield nut and bolts(use a rachet wrench) and breaking the Starter bolts loose. And removing the connector for the starter
@robr8a23dogg6 2 жыл бұрын
It ain't that hard to take out the manifold.. I think it took you longer to do it this way than to take out the whole manifold
@danielx7922 2 жыл бұрын
You're right brother but most people are not comfortable removing it
@Autowill 2 жыл бұрын
Is this the same process for an 01 is300?
@danielx7922 Жыл бұрын
I'm sorry for the late reply I didn't see your message. Yeah should be the same
@user-mx4et6mn3u 2 жыл бұрын
Nice work around to removing the intake. 👍 if only I had a longer handled ratchet. ☹️ I’ll be removing the intake to replace mine and clean the intake and stuff out while doing so. This is really good to know that it’s possible. I wonder if Toyota does this but just charges us the 1-2 extra hrs to remove and reinstall the “intake”. Ha
@danielx7922 2 жыл бұрын
I'm sorry bro I didn't never got a notification of you guys comments. How did it go??
@kraziejavier 3 жыл бұрын
Is everything done from the bottom
@danielx7922 3 жыл бұрын
You can but its easier if you remove the alternator bolts and nut from both angles. Which ever angle that's easier for you. The O2sensor connector, the crankshaft sensor connector and the alternator connector were easier for me to disconnect them from the top
@kraziejavier 3 жыл бұрын
@@danielx7922 thank you I just replaced it awesome video but did not work for me
@TuanNgo-ry2gu 3 жыл бұрын
Do it when cleaning intake manifold...
@whowantstoknow8492 3 жыл бұрын
looks like a pain in the ass! i hate the way shit like this is designed