Not clear. Maybe lift up so can see how it’s done

This is a Powerline Functional Trainer Body Solid PFT100

hi, In the description you talk about the Body-Solid GFT100 model but in the video you are shoving another model

Gympin is what you were thinking of for extra weight on the stacks

You're an absolute legend 👍👍👍 thanks so much for this video I bought a 2nd hand Body Solid Fusion 600 in February just to give me some variety away from the free weights and the guide rods would slip out the bottom also, though I was wondering whether it was my unlevel garage floor contributing to it or not I did buy new Allen grub screws for those terrible plastic bushings as the old grub screws were pretty loose, however using those chrome bushings like what you did looks a good fix to hold it into place I haven't bothered trying to recable it yet as it's a bit of a 2 man job being an all in one trainer, however after I clear out a portion of my garage I'll put the Fusion 600 in an area I'm hoping is more level for the floor and I'll re test it out, but I reckon I'll follow your lead here in the end

Thank you for the video! I have a 2010 Pathfinder. Just got my AC fixed and 2 days later it was blowing warm. Checked the air filters and when I pulled those out some leaves had fallen into the blower motor and it started vibrating and sounded super loud but the AC was cold again! Pulled out the blower motor and sure enough there was a leaf inside there. Cleaned that debris out, put the motor back in, which seems like it forever to hold it up and get it back in place, but finally did it! Took a couple hours I think but its all fixed now! Saved myself another trip to the mechanic, learned something new and have ice cold AC! Thanks again!

So you fail to include the hardest part in your video. Which was removing the bearing

I just watched your video because when I went to clean the filter, I notied that the bucket was full and I thought the pump must not be working. After watching the video and reading your comments, I should not be concerned if the bucket is full as long as the machine does not shut off. It seems you are saying that the pump doesn't kick in until the bucket is full. Should I expect it to drain down completely? Is that one filter the one large rectangular filter the only one I have to worry about cleaning? Thanks for all your help!!!

Mine doesn’t have a drain hose to the outside, I have to dump the bucket when I is full and shuts off. My question is when I dump the water ever once in a while it leaks water all over the floor.

Can both stations go off at the same time or one at a time?

concrete is considered a porous surface and this stuff says it last 12 months on non-porous, i am happy to hear it lasted for you the whole year i wonder if the siding gap helped keep runoff water from washing down the treatment

I'm glad you had luck with that stuff.I tried it for a few years but finally had to hire a professional with products not available at big box stores. I had carpenter ants and that did nothing. I can count the number of ants on 3 fingers at most seen in my house every year since I got the real stuff.

excellent video

When the pump works should it empty the bucket?

if this video never existed I would've thrown my camera away. You solved my problmes within 13 minutes . Thank you so much

My buttons don’t work. I made a year in April and it wants to quit the next month. This is horrible.

Thank you very much.

Spent hours trying to re connect to new router still won’t connect this way? Thanks for your help

Thanks for the information. I wish I was in the US and able to buy your Ksendalo drying rack but it's too expensive to get it shipped to the UK. If anyone from the UK reads this and cares we can get an Ikea version on sale for only £2. Much less than Amazon sells it for! So far I have the pots & the SS utensil holder. Need to get the bolt and the nuts & washers then I will be all set. :) I just need to ensure my greenhouse doesn't drop too low during these "spring nights." Just one small point I would add is that new clay pots here in the UK seem to have larger holes, so, in order to spread the load of the washer around the pot surface my OH suggested it would be prudent to get washers as big as I could. My washers are 8 thread by 50mm and give a large spread across the large poot surface.

I just bought one of these and it doesn't seem to lower the humidity at all. It's sucking out some water, but it doesn't drop at all. I had a frigidaire in the same spot that would drop it immediately until it died on me

Not so easy, tee hee hee. 16 minutes, yikes, I have 8 of these cameras, yikes

Hello again-- I wrote to you on your first video with your pump working very little. I am going to try your fix when I find those tabs and then I will get back to you. But my other question is I see that your bucket is FULL-- so the pump action should be working since the bucket is FULL- right?? But then why isn't the Bucket FULL light ON?? Can you explain the reason why that light is NOT on and yet the bucket IS full and thus the pump should be ON? Ad have you emptied the bucket at all and when doing this- does the pump start again once the bucket fills up again? Thank you for these in-depth videos.

Hello. I have the exact same problem and mine was purchased in October of 2023 but since i had a flood in my basement that was just fixed etc we just started to use this unit. So it is under warranty and homelabs sent me a new unit and allowed me to keep the old one. That is good customer service. But here is what my unit did. When i first installed the first unit the bucket filled and the pump started and i also have it stuck in the drain area of my washing machine into a drilled hole like you. The pump worked great. A heavy stream of water was coming out. But the instructions said to empty the bucket every 2 weeks to prevent mildew in the water. So i did it after 3-4 days and now the unit has stopped pumping altogether. The bucket is up to the top and still no pumping?? And no water coming out of the bucket either. No overflow? It occasionally turns off for a minute or more then turns back on. So I am not sure what is going on. I am thinking it may be the pump hose inside the unit that maybe fell when i removed the bucket the first time or like you said that metal piece. Is that the pump hose and how or what and where should i look for to check that? My tesl concern is that if i have to clean the bucket lets say monthly as they suggest that is what caused this problem to begin with. My old unit did not have to have a full bucket for the pump to work so u never had to worry about the bucket ever?? So please let me know exactly what they mean about the pump hose inside the bucket area falling down and how to fix it. Thank u and good luck

Many thanks; even after eight years! 😊

I made one of these roughly the same size and for the winter nights me and my wife closed all doors to our living room and from mid afternoon to late evening it kept the room to 19 to 21 degrees c. I really love it and I also used it In my garage when i needed to dry out the Ceiling took a few days having to pop in there adding more candles but blooming worked

Have you tried the other type of bidet with the turning knob? Thats the kind I have, seems easier. And also I squat when I pee to not make a mess. Haha much better

This was very easy to follow thank you so much.

I will try thanks. It was working for 7 months pumping fine.

Man, that was awesome thank you I finally got it set so I think we’re good to go. Really appreciate you posting this video.

Life saver. Thank you so much!!

Thank you! Very helpful and I'm off to buy a new transformer...and off to see how to test a gfci first, as I don't know how to test if it is bad or going bad.

Seems like this optical system has been unreliable for years

Did you get a dash message "no warning tones" ?😊

Thank you! Will purchase these!

Hi, Just wanted to know if you are still pursuing a career in aviation.

I’m sure you could but it’s not my intention. While they are growing it could look cluttered etc. To me this just looks great itself and sounds great. I do appreciate your comment and the idea. I’m just going for the simple look and sound. 😊

What if I had 2.4 ghz prior to having issues and i cannot find the 2.4 ghz option anymore. Internet update 😢

I have 12v power to my ano, and red light blinking at the fiber optic, and no sound, resently i trued with another amp, and still there is no sound? Do i need coding for installing new amp? Or should i check somwere else ? I tought power and signal should be enough?

There's just no comparison. For starters: Bambu Lab is a Team of former DJI employees who raised 55 Million dollars on a kickstarter campaign to create this Core XY machine. That alone put them light years ahead of the 'race to the bottom' manufacturers. Prior to owning a P1P, I had a fleet of Ender 2 Pros (I also have the original Ender 2) and I had them fully tuned - since they're smaller they're easier to dial in than a larger Ender 3. My Ender 2 Pros have all been sold or given away. I feel bad for the newbies who are just getting into 3D printing and are under the false assumption that all 3D printers are the same - They're Not. Prior to Bambu Lab - 3D printers were kind of like Go Karts where it required tinkering galore and something was Always breaking or in need of attention / tuning. The Bambu Lab machines are equivalent to a New Car.

If this helped you don’t waste another minute thinking about it. Buy the Bidet and feel clean and healthy the rest of your life.

Thank You]

Thank you so much i did it how you said and it works thanks

kzbin.info/www/bejne/bZ2tnp6KiNSKgsUsi=TOEL4OClrB69YBSr Sub 2 minute benchie.....on a ender 3 😆 Ender 3 v3 is core xz and has 600mm 20k accell printing capability stock, for around half the cost of the p1p....stock with hardened nozzle too...

I have a P1S, I used to have an Ender 3 Pro plus various improvements. The P1S beats the Ender 3 to death in almost every way possible. The only thing I think the Ender 3 was better for is it had a USB port so it was possible to run Octoprint to control it. Otherwise the P1S is about 3-4x as fast, has ABL, a smaller footprint, larger build volume and my AMS makes it super easy to switch filaments.

I do understand this is a comparison from your personal use experience, however these are 2 different machines with different kinematics and should not be compared.

Thanks for the comment, they help everyone 😊 I am however just going to stick to the Bambu. So much less hassle and just a joy to print as it should be. No messing with settings. They just truly print amazing.

Thank you i got this for my sons dust mite allergies and im going to get him a new mattress and box spring he only sneezes at night 😭😭and hes on Claritin and nasocourt thank you for the detailed information sleepless in NYC 😴😴🗽🗽🗽🗽

Creality does make a Ender that's getting closer to the speed of maybe the A1/A1 Mini, it's the all new core XZ Ender 3 V3 nothing after V3. It's a klipper machine and fast, I have the Creality CR-10 SE which despite the CR it's a Ender sized 3d printer Klipper based and it also is very fast. Not X1C, P1S or P1P speeds but close to A1/A1 mini speeds. I have an X1C so know what you're talking about the speed of these things. Oh, use Orca for all your printers, I use Orca for my CR-10 SE and my Bambu printers, you can do anything in it you can do in Bambu Studio and more. I have rooted the CR-10 SE and can see my printer when I click on the device tab of Orca just like you see the P1P in Bambu Studio.

the ender fan boys should thank us for buying bambus so they can get $50 ender 3s all day long, they rewally seem to try to cope with owning them .. love both of my bambus

My solution was throwing mine away 🎉 I had another one anyways and it worked instantly, have a feeling the other one had a broken button.