What was part number

Another video that didn't show anything.

thank you so much buddy

Thanks mate. Worked perfectly! You’re still helping people!

Juat used the screw driver method. These new alarm ones are a pain the ass. Older ones took less than 30 seconds. 😂

I prefer some wire cutters less damage to bottle lol

The music was creepy and annoying

Thank you so much, Man with the wisdom. 🤍🌈🥰

That's awesome

great video. any tips on re-assembly?? particularly getting the belt back around the drum?

Hero

Kitammuort, pe miracol nn m'agg struppiat

Strong magnetic works

I just turned it upside down and hit it with a hammer at an angle towards the ground and it came off. Broke the cap a little but it still screwed back on.

Use a fucking magnet

I used a hacksaw. I tried using the flat head but it started cutting into the glass. You might need two people with the hacksaw because the bottle will move on you too much.

Omg that baby is the cutest

I bought an air chisel yesterday on the strength of your video. I`ll try it out today I have the upper control arms off my `80 G10 Van ready on the bench.. cheers. watch for update.

Thank you

Can that be done while still on the car?

lol I was afraid the bottle would break, but eventually I was able to pry the top off

But... how long did it work ?? Ive put 4 different brands and styles on my kubota, full electric power at all times.... the pumps dont last a day ??!!

Thanks so much! Great tip. I don't have the strongest air chisel but it took the bushings out with ease in minutes.

Could you provide a link to where you got the part

Mine won’t has no power what can I do

Broke the bottle. Moronic advice.

Holy Smokes Dan..... Looking for a video to help me repair my dryer and you pop up! Small world. From intubation and ACLS to appliance repair. Thanks man!

I went to crank my B3350 and the red engine warning light came on after it started up and the throttle wouldn't do anything. My dealer who is pretty good at helping out suggested that because it didn't throw a code it was probably fuel related and not electrical or a catastrophic failure. I changed the filter (it was dirty but wasn't the fix) and then unhooked the fuel pump with tips from your video and made sure it flowed good fuel. It now works perfectly 👌. You saved me at least $1,000.00, thanks!

Thank You - 2 of 6 boxed bottles of Dewars scotch had locks on them (from Woodman's) THANK YOU!

Thanks for sharing. 👍

I find it funny that you ended the video without removing the old spring and putting the new back in. I'm guessing it wasn't as easy as you claimed.

It would have been nice if there wasn't music drowning you out and if you weren't figuring things out as you were making the video. The stuff I wanted to know you didn't show and just said that you did, like taking the door and front stuff off.

Mine are from a 1967 Buick Riviera. Mine are taking hours!!!!

You know it would have made it a whole lot easier to get to if you went in from the bottom

Can you come help sos

Yes still having troubles here

Its the only way to fly.....

Question

I will try this method tomorrow!

I don't recommend this video at all. Eventually my screwdriver broke the glass at bottle's neck.

so did you replace it 2 times or did someone else work on it the first time? how many miles on that car when senor failed...thanks for sharing.

I bought this cheap scan tool off of ebay for $18 4 years ago...and plugged into my nissan which broke down suddenly...just cranked but no attempt to start... This tool pin pointed it was my cam sensor ..which is very easy to change...replaced it and it started right up( this was the original plastic part my car has 121 k)...never changed my crank sensor which is same exact part on my 2005 altima...

Good Job, Keep up the Good Work!

Great job thanks to Jr. Lol

Because stuff breaks has an easier tutorial for this and covers a safety precaution. kzbin.info/www/bejne/rZewi3yCoqmDhpo

How do you get the belt off the tensioner?

Can you or somebody help me please? the wire on the top at 3:13, was that plugged into anything? I took mine apart and cant find where to plug that one in???

Glad that I found this video although it didn't help with the bottle that I had an issue with today since it isn't long-necked and I couldn't get a screwdriver under the edge. I read a comment below from Robbie stating just to take a hammer to the side part and it popped off. Yay!!!

No Brasil não tem. Vai chegar daqui trinta anos.

Ok where are the cones ? Why not block that lane ???