good video. Great Old Holley Bug Spray.

From which vendor did you obtain the panels? Nice work👍

I watched all 3 parts. I'm thoroughly impressed with the job you've done. I've never torn down a compressor before, but now I see it isn't too bad. Actually looks a little easier than some small engines. I like how you used good old ingenuity to refit that worn connecting rod. I did that with an old Kohler engine once and it worked fine. Good job bro.

Very cool 👍 Where did you get the rings? I can't find them online 🤔

What flaring tool is that? Manufacturer?

Thought you were a woman...

Thankyou, i am doing a simullllar project....i needed straight forward how to... I do have one sillly question, where and how did you do your battery

Music too loud.Can’t hear a thing you’re saying.

Nice job bro.

great install ..will use that when I do mine ..

Inspirational

Jesus H Dimpled Christ. I can't get thru it all . I'm sorry

Great info , on my belle the fore and aft is off i feel like the door was sprung open to wide would this cure that problem

Sure wish you would come back . Your way of showing what needs to be done and what to use have inspired me to do some mods and repairs to my bug . Bob

You should have a link for the full version video. I see you doing more explaining on the fast forwarding parts of the video.

Iwould like you to that job for me ..can you??

Can you do these for me

Can you do these for me

I just stumbled across this video... great work! I have a 59 bug, and the same bluetooth amp and was wondering how you wired it up? I'm assuming that the yellow power wire goes to the + battery terminal, and the black ground goes to - battery terminal, and then I was thinking the blue power on/off could go to the ignition fuse under the hood... would that work?

Would it not be better to fit it below the master to avoid airlock problems?

Your videos are the most to the point and informative on the internet . Im in the process of restoring a 1957 oval and you have been a great help . Thanks

I found a problem with removing the hinges. The sheet metal has been extruded to match the counter sinks in the hinge for location. They don't just pull out. Now, this replacement has become complicated

Where did you get the parts,mine got low on oil and stuck. Changingboil got it running,but id rather rebuild it. Mines a Campbell Hausfeld 4hp 20 gallon iron series,the pump looks l8ke yours. Thanks in advance.

Hi great work it is a pleasure to watch your channel and how caring you are. im running same kind of idea but was wondering if you could tell me bolt sizes for mounting to hood and the bolt number that attaches to car on the other end of hinge. thank you for any help. love your channel keep up the great work you do. Todd from Burnaby b.c. Canada

That was a great video! If you keep your vent window, can you mount the switch behind the frame instead of cutting the door? Thanks!

Brother, thank you for the video, very good, told me everything to plumb it it, now on to pt 2 to electrical it! Very helpful video, took the worry right away man!!!

Is there a left and right hinge or are they universal

The old heavy duty ones also have a much better duty cycle & in most cases have better cfm.

Thanks!

I picked up a sand rail to rebuild. Finished 2276 for it, and now to front end. Your videos are great! Thank you very much! I know nothing about this vehicle and you’re a tremendous help in getting this done correctly. 🤜🤛🙏

Would you anticipate all of the same problems/modifications being needed for a 74 Super Beetle with the quarter window?

what type of engine did you use

What happened to this project?!?!

If you’re going to do a segment featuring a kit like this how about putting a link for the part in the description. Or at least show the part number in the video so your viewers don’t have to go searching for it.

3 Years later Jan 31 2024 they are still making them wrong and still selling them and they do not line up. How many people are screwing up there new floors trying to get them to fit. I am sure the seller and the manufacturer of these parts knows they are not correct, but they keep on selling them this way.

Nice work congrats, I have the same harnes can you share the diagram plz?

UMM!

What's the status of Curt's bug?

Have you done band instrument repair? I see tools that you use that are fairly specific to that profession.

this was AWESOME thank you

Excellent video and instruction

Bro, welcome back! What's up with Curts Bug????

Hey I just drove by your 55 at the O'Reilly in Rosemount

Next time for health and safety you should be wearing your organ vapour cartridge respirator while gassing like you had done with the stripper. Nice watching your series 🤙

It's like it's smiling...Bravo!

Going to be a nice dune buggy when you're finished... First time I've seen your channel, very nice video...

Stop fast-forwarding so much you need to talk more about what you're doing. Viewers can see you doing things you never mentioned

The music is extremely annoying and distracting.

Did anyone else count the "UMMS"?.

We enjoyed your work here. Thank you for letting us experience it with you and your son. Good memories for all!