Hey thanks for the classic video. What did you do for the front spring to lift it? Are they stock?

If you know a fat bloke with boots, you can get him to stand on them and push them in too!

3.2 engine?

if you didnt want the grease on the thread wouldn't you have put the bolt through first then applied grease?

What’s the bulbs for fog light? Ty

Good job buddy, and yep easier through the wheel arch 😎😎👍👍

Great tutorial

Gracias!!

I need your help. I have a 2018 Mitsubishi ASX and was about to order an LED bulb from Amazon, but I'm confused about which bulb to buy for the low beam. Is it the same bulb that goes in both the high and low beams, or is it a different model for the high beam, low beam, and fog lights?

Looks beautiful 😂😂

How is the quality of this brand of springs?

Thankyou

Replace my rear one at the weekend. friend has the spring compressor tools. but cant use them as limited room. we did similar to what you did using the jack. place a few bricks under it as height increased incase something slipped! the motor dealers gave me the wrong spring even though they put my reg through the system. luckily they another had one in stock.!

Thanks for the specs.

Where did you find the torque specs at??

Thnx for this one I been looking for this bushings brand 🙏

can you share the link of the product pls

Didn't bleed them

Two 10s and a 13? For the bolts?

Legend, just saved some serious cash with your help, many thanks

using a vice was 100% a big brain move

Thank you very much. I don't have the same problem. It was just that the handbrake handle was stuck to the outside and I couldn't get it back. You saved my day.❤

Ja sam zamenio sam jednu oprugu napred,,pukla je ..da li je to problem?

There's gotta be an easier way to replace this bushing without removing the entire trailing arm.

Excellent JOB MATE!

🌟🌟🌟🌟🌟👍🇺🇦

In the day, Magenta was a wild colour, but it suited the R/T's. Mate had one in '75 and I swear you could almost see the fuel level drop when pushing hard through the gears.

What model year is your Prelude?

Which car's spring goes?

You shoould have used gloves, engine oil is bad for skin

Great video. Saved me £100. Disc pads still good at 91,000 miles on my outlander.

Thanks for the video

When you greased the other pin and slid it through the gator the grease slid up and was deposited on the thread?

Good job, very fiddly by the looks of it but you made it look easy 👏

A hint for the future that you specify the type of bulb in the description or tell about it in the video. I guess it's obvious to you what kind of bulb you need to put in, but since so many people are watching this video, it's obviously not that clear, so please include the specs of the bulb and from time to time answer some questions in the comments.

No info about type of light socket used for ASX, good video!

And what brand is the spray putty? Your thumb covered the name.

I know its been a few years but can you tell me the specific clear coat you used? Thanks

So bloody easy

My wife's ASX has got one head light doesn't work, so your video is very helpful. I give a sub💪🏻. Last thing before I buy new one, do you remember what type of bulb was that?

Great video

You may need to invest in some ratcheting wrenches!!

Thank you. I just changed mine after asking a mate for help for over one month now.

Mines been doing the same thing and I sent a video to my buddy and it was fine 😂😂😂

You made it look easy getting the old bushing out. I have watch others drilled and used heat to get it out.

The directions worked, and it is the best video to fix the clock spring

Hey Jay, Would you happen to know if the ZG Mitsubishi Outlander shares same suspension setup for thr ZL Mitsubishi Outlander. Looking at improving height and strength for towing a camper trailer.

Thank you so much for sharing. Just got a 2007 , music controls don't work. Wasn't told by seller ( didn't think to check ) going to give this a whirl and see if it sorts the problem.

This is exactly what I was looking for

Those pan head screws are a pain!