AlarmPro AlarmPro

Пікірлер

@PercyOReilly-g5s 10 ай бұрын

Hi, how can I setup the uTx to trigger an HQ from an external NC/NO contact from another independent device ?

@PercyOReilly-g5s 10 ай бұрын

Hi, still not clear how to setupup the uTx

@robyngarden 10 ай бұрын

Where is next video to label zones

@alarmproalarmpro2315 10 ай бұрын

RENAME Z2 braai Note uppercase command.

@wernerpieterse4295 2 жыл бұрын

can you connect a robogaurd to a hikvision wireless alarm ?

@ElecAndAll 2 жыл бұрын

The receiver codes are different. So far the roboguard can be connected to a supaplex and an Hq. I'm not aware of any others that are compatible.

@Thamas825 2 жыл бұрын

Hi , Nolan her . Just a question , can you reset the hg to factory settings , regards

@alarmproalarmpro2315 2 жыл бұрын

Hi, no I am not aware. You will have to manually delete the zone programming

@mhlofoz 3 жыл бұрын

Hi there, please can you assist me with my current issue, when my HQ is armed 20 minutes later the status light will start flashing but the beam will continue working perfectly but has a delay when walking pass it… Please advise what could be the issue?

@alarmproalarmpro2315 3 жыл бұрын

Have you checked the batteries in the beam? We can supply the kinetic batteries for R250. That should resolve the problem. If it's old then it could be that the transmitter top eye needs replacing. You can bring it to us and we can repair it.

@mhlofoz 3 жыл бұрын

Thank you for coming back to me , the strange part is the the device is 3 weeks old…So I’m not sure what the issue could be. I can still arm it with no issue but it’s the status light flashes after a while which worries me, then when I do the walk around test… I definitely have a delay on the HQ beep.

@alarmproalarmpro2315 3 жыл бұрын

You should've bought from us. We test and program each one before despatch.

@mhlofoz 3 жыл бұрын

@@alarmproalarmpro2315 unfortunately I didn’t know about you guys. What can I do in this case, do you think I should replace the batteries and take it from there?

@supertroepie260 4 жыл бұрын

Good Day! My HQ has stopped beeping, no sound whatsoever. The zones are still picking up movement, but HQ doesn't beep. The zone on HQ flashes when it picks up movement. Only thing I did was replace batteries for zone 1, since then no sound. Any ideas?

@alarmproalarmpro2315 4 жыл бұрын

Howsit, hehe, yes this is a common issue, you just need to replace the HQ 8 ohm speaker, problem solved.

@supertroepie260 4 жыл бұрын

@@alarmproalarmpro2315 thanks i thought maybe so

@colinmcculloch9338 4 жыл бұрын

Thank you very much for the awesome help given to me, after many days of pulling my hair out , Muhammad went out of his way, late into the night to help me resolve the challenges I had getting the roboguard HQ and robotext to work together flawlessly, thanks

@alarmproalarmpro2315 4 жыл бұрын

Glad I could help

@saadally2172 4 жыл бұрын

Thanks for this video really helped!

@saadally2172 4 жыл бұрын

Awesome video!

@investmentcompany5792 4 жыл бұрын

Hi. Wonder if you could do a video on the alarm interface module for roboguard

@alarmproalarmpro2315 4 жыл бұрын

Hello, I'll show you how to do that with Robotext instead. It's much simpler and easier.

@investmentcompany5792 4 жыл бұрын

AlarmPro AlarmPro what's your email address?

@alarmproalarmpro2315 4 жыл бұрын

@@investmentcompany5792 connect with us on Facebook or Robotext.co.za

@naseeramitha 4 жыл бұрын

Awesome👍

@alarmproalarmpro2315 4 жыл бұрын

Thank you! Cheers!

@muhammadally7882 6 жыл бұрын

Thanks good video

Ең жақсы KZbin

Пікірлер