Is there a way to fix the slider or it can ONLY be replaced ..? My slider rod fixture is straighforward. I was hoping to get some idea about how the slider can be fixed. My slider wont stay in place and the lefthand side tightening screw head doesnt hold the slider. The slider slides down to the bottom bringing the shower head down.

Brilliant video; very detailed and informative. Shower now serviced with seal kit from you and working perfectly!

Thank you so much....Im about to replace mine now..circa 28th Sept 2024

Q, When you purchase a 903.33 cartridge from your website for £184.60, does it come with the trim & knob pack as part of the deal? + mira quad key as part of the pack?

My Mira escape is running hot

Hi guys Shower will not turn on/off via unit start button, will only start if I turn the main switch on/off behind the shower wall. Any how to resolve

Hi,my mira shower sport max 10.8 go from scalding hot to freezing cold on its own,tested thermal switch and it does have continuity,can it still be faulty?i have ordered one today from your website anyway,its probably 2-3 years old and sometimes i will 20 minutes under shower just waiting for the cooler or warmer water😤🤦‍♂️, thanks

I have a tempature control Grohe valve that is stuck and know it’s stripped. Any suggestions on how to get this out.

what could be the reason for an electric shower to make a banging noise when changing from cold setting to hot setting? Thanks

I have an Aqualisa 605 that runs cold even if there is hot water available. Can the mixing ratio be adjusted?

Hi, the latching switch (416.48) for my shower is now discontinued and marked as out of stock...does that mean I need to scrap my 4 year old shower? (Mira Azora)

30 years after installation, the seals have gone. A quick purchase on the Internet and a visit to this fantastic video and my old 88 is as good as new! Thank you Sir!!

Part one and two were excellent and really helpful thank you! I have all the confidence of a fully qualified spanner monkey now! 😂

Oh dear. Just tried this with my faulty Triton Cara and when I removed the coil as shown in the vid, water poured out of the shower and all over the bathroom floor. I'd obviously not quite turned the water off properly. Unfortunately, the new coil now won't fix back onto the valve and so I can't turn the house water back on. Any tips for isolating the shower's water supply, so we can turn the water back on at the mains to wash in sinks, drink water and go to the loo?!! Has been a total disaster :(

Hi. I have an aqua Lisa Doing all you have shown (thank you) unfortunately I have 1 of the cartridge screws out but the other 3 are extremely rust bound. Is there anything left to do before I have to replace the shower. ? Many thanks in advance Kind Regards Lee

1st Class.... just overhauled the 2 Mira showers on my 30 year old motor cruiser. 👍👍👍👍

Mine is only brand new. I just replaced one… now I’m wondering did the old one even need changing

Very clear thanks .... brilliant vids

Excellent video, help me identify the fault, know the part and how to fit the TCO. Great video. Shower working great again.

Thanks for this superb video. It always adds a degree of professionalism if you show competence witha multimeter and thanks to you, I was able to do so. I have replaced a few of these before and it never occurred to me to just loosen the earth pole screw, instead of removing it completely and carefully leaving the remaining two screws in situ, in the wire connectors. I managed to cannabilise an old TCO from another Mira shower. The job was done for a mate and he had just bought a like-for-like shower for a staggering £320!! He was made up when the repair saved him just under £300, as he was set to take a modest holiday with his family and money would have been tight if the complete unit had been changed. I have purchaed Shower Doctor products on more than a few occassions and in gratitude, will order another 416.41 ASAP.

Thanks for your Mira 723 video, replaced 936.59 service kit on Friday 02/08/22 with your help. Thanks George and regards from Brendan.

Fantastic videos and advice. Mended my Mira Sport by changing the solenoid; cost less than £20 and didn't take too long at all

Thanks

Thanks. All sorted now.

Great video, I've just replaced the thermal cut out as per your video, and it worked! Thanks, you saved me a fortune.

Hello-how do i know why switch on the fuse box is connected to the shower?

Thanks, I used this video to determine that it was the filters either side of the inlets that were clogged up. After cleaning them, it's working better than ever! I also used the other video by shower doctor to calibrate the temperature! Thanks Shower Doctor!

I managed to replace the shower cartridge three years ago and the same problem has happened again. I did purchase another cartridge but for some reason I’m getting no hot water. I purchased the entire replacement system like you have in your video but for some reason even the handle turns the opposite way when I turn the water on and I don’t get any pressure until I turn small until I get cold water flows, any idea why this is happening?

I have a Mira Sport shower and today when it was powering down, I heard a hissing sound and when i turned the shower back on its only pushing out cold water.

Many thanks for your instructions

I am finding that after removing and cleaning my cartridge (soaking in white vinegar to remove limescale) that it will not push in quite far enough in order to refit the grub screw. The hole in the cartridge does not quite align with that in the housing. Hammering it seems to be the only option but surely there must be a better way?

If the drip is on a combi boiler the boiler won't fire on the drip. If no meter the water isn't a cost. Still its good for the environment to fix

Ahem.....you forgot to mention the split nylon ring in front of the O ring.

Hi, do you have video on replacing prd on a selectronic shower please? It doesn’t seem as straightforward as most, thank you.

How do you shut of the water before replacing the valve?

Great video, best on youtube....fixed the shower a new TCO....Thanks!

why is the preassure lower when i turn it to hot water? on a Grohe....

If I've stupidly put that wax thermostat the wrong way round will it make any difference?

I would put reliability as the no. 1 feature. Unfortunately, Salamander pumps do not have this.

Need to show, not just talk.

Much appreciated just fixed mine

You didn't mention a splash guard at all in the video. I had this small thin flap of plastic fall on the floor when I removed the cover and on it it said warning do not remove splashguard. I am a bit confused as didn't know if this was the splashguard or not and couldn't see how to put it back in. On your video you made no mention of it so I assumed it couldn't be the 'splashguard' and was probably just there to give the message. Can you shed any light on this, my model is a Mira Sprint. I did follow your very helpful video and managed to replace the part and fix the problem so I am very happy. Purchased the part from your link too, rude not to!

Shame you did not demonstrate the tricky bit - the O ring replacement - because, as you say, this is the first question the manufacturer asks if a fault develops. Also you do not explain what the o ring does and when it must be replaced.

Top man

Brilliant explanation, worked a treat. Thank you! Are you related to John Higgins, the snooker player, by any chance? You look and sound like him, but you were much more uselful :):)

Thank you for this video. I changed the cartridge which was leaking and causing air locks in the shower.

Thanks very helpful

this video helped me so much, I was able to replace my tco and get my shower working again thanks to this all for the price of a takeaway. thank you!

You are great, man! We are 2 women and thanks to your video managed to open and clean it. Thanks!

excellent, clear explanation. thank you