I don't want to be too critical, because all-in-all it was a decent video. but... you missed some important steps and a couple of errors. As noted in earlier the 6 torx bolts are E10 not E11. I suspect E11 will work because of the torx pattern & low torque required, but use E10. I may have missed it, but I saw nothing on the torque converter and the fluid in it. Some of the 722.9's have access to the torque converter and some don't. It is an access port (w/black rubber cover) just in front of the oil pan you were working on. There is a process for that which involves leaving the car in neutral and turning the crank to find the drain for the torque converter. The 6 torx bolts due have a torque based installation it is 4 newton-meters (which is just past finger tight) plus 180 degree turn. They are stretch bolts and too much tightening will snap them. Also, while running once the tranny is above 35 celcius (on your way up to the 45 celcius fully warm operating temperature) you should get in the car foot on the brake and cycle through the gears P-N-R-D1-D2 and back a couple of times. For the pump I found a $50 one that worked great on Amazon (LainKeen). Without a lift this job can be quite messy.

The bolts are all e10’s, get a flat head and pop the level plug completely into the pan so you can get most the fluid out. Also you waisted a shit ton of fluid.

Im going to do my glk350 in the coming days. Your video is very informative. Thanks!!😊

How many miles did ur car have before at the time of this service?

where you located bro do you lower people's car for a price?

Well done! Thanks

An man that was your time to put a real motor and n it! At least the ls3. Not the 2 😂

Hi can u write me on my new email Please need info on c300 2018 4 cyclinder 9 speed sedan

Dude's just teasing us now. I've been waiting to hear this Rev9 manifold for so long.

Wowh

Hold up I already did my valve covers … I don’t take the plenum off again just to tighten the sprockets to spec

Want to know where you got the kit? I have a 2018 c 300 and it needs the transmission fluid replaced.

What size hub was this specific one?

Beautiful work 🔥

Where in washington are you at brother?? I'm in Vancouver

I just got a 2020 c300 I want to get 2 valve controlled mufflers and replace the original ones in the back have you done the center resonator yet? Because I’m debating on removing that a-swell but with valves closed I want the car to sound completely quiet like it does stock

Mooo booost

Link to the conversion kit for the injector upgrade?

I guess the turbo is just a great muffler.

Hi 😅. I have oil build up on the spark ( the 2 part of it) i changed it...then i found pcv not work...i changed it....but what is the cause for oil ?

I don't like this video I don't get it why you cut your mint condition rust-free R32 skyline you should have left this stock you should have only put lips inside skirts that's it

So the motor "tics" ?

3:46 🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣

Way to go Royce!! Awesome to see him working in the garage with Dad.

Awesome video! Do you have any videos for the coolant change? Thanks

Dude! Great walkthrough on that PSP rebuild. No powder coating of the housing though?

I have that oil pump but not the fitting for the transmission or the thicker clear tube you attached to it. Where did you get those?

NOT a flush. Just an oil change. Wrong title.

How much does the widebody cost?

Loved the video, it’s real educational and you kept in lessons learned too.

Super helpful video thank you so much!

Links?

Man, for the IAC mounting why didn't you just countersink the holes to what they should have been?

My c180 loses power on acceleration and sometimes it's very slow uphills. it seems to struggle on changing gears Gear 3 to 4 and 4 to 5 What it can be the problem Sir @DriftMagic

I can't seem to find the rear camber arms on Maxpeeding Rods site? I already have their coilovers and could do with some extra camber in the rear.

Thank you so much you made it so much easier for me. God bless.

Hi mate do you recommend that we can use aftermarket fluid in Mercedes

Is there spec how much to torque bolts in installation?

What size fans did you get, both 16”?

Thank you for the video! I can see the tyre and rim size has been modified, can you share the Tyre size and rim design, please? Looks very cool!

Was the experience good?

Nice all from Maxspeeding rods

Awesome video, I don't think it'll ever apply to me specifically but great quality and very informative

How is you not viral yet

Great video! Sold on the max speed suspension!

Wowwww such good recording

How many miles on your car ? Awesome video

Great video very thorough!

What transmission is it? Do you have the one from s13 left ?

Great video thanks