Depending on tyre size, you also may need to let air out of the tyres, especially on mountain bikes.

Thanks for the tip to squeeze the caliper and lift the noodle. I had been unscrewing the bolt that secures the cable before. This is way easier and requires less recalibration after reinstalling the wheel.

the dropper seat post wasn't installed. on fact the cable hang out the frame and wasn't attached to the bar nor the seat post at all.

I have been trying to take the wheel off my bike for the past 10 minutes and thanks to the first 30 seconds of this I finally figured it out

Oh pal, you’re a lifesaver! I was searching for a tutorial just like this, so simple and guiding :’) Thanks a bunch!

Ty ,,,excelent info,,too much videos for disc brakes ,,and a few with v brakes,,

Can I please request a video on how to set up the suspension? Thanks again for all your hard work!

Great job!

just the best video plain english well presented and easy to understand Im just about to get my first full sus bike and this proved extremely helpful thanks a lot!!

Thank you for a very straightforward video, I needed to find a way to show someone how to take their bike wheel off quickly and this was probably better than any verbal description I could have given. 😂

Wonderful demonstration Michael , so clear and easy to follow. Great teacher.

Super video. Well presented and explained. Very good and thank you!

can you make a video on troubleshooting for some reason, the spring adjustments aren't working, and one of my break pads rubs against the rim no matter whether the adjustment screw is out or turned in all the way

I only wish whoever edited this video didn't think that that awful, annoying music was needed. When are video editors ever going to learn that simple fact?

Good video. My problem is when I replace the brake pad, it twists as I snug up the bolt. There are other brake pad designs on older bikes where this is worse problem, you need three hands. I'm aware of the "third hand" device but mine doesn't fit the cantilever type brakes shown in this video

Incomplete. What if one side touches the wheel first??

Thank you Michael! I have not had a lot of experience with V bakes nd your walk through was perfect. Will look forward to more videos from you.

What the name of the bike?

Thank you very much. That was really helpful and allowed me to sort out an ongoing problem.

Love the backing track

This is a useless hack nectar it assumes all bike owners drive freaking hatchbacks. Let us see you load it into a 4 door Camry. 🤣

Thank you. At last a simple guide that is easy to follow and actually teaches me what to do. I am really grateful.

Very well put together video and very informative but straight to the point. Thank you

Nigel Mansel thanks for this

Thanks for this! I keep trying to look up what's wrong with my v-brakes, and they're apparently missing the springs. No wonder they're loose and not braking properly!

I've been nervous about removing the wheel on a bike I bought several years ago due to the breaks possibly closing. Thank you for showing how easy this actually is.

In lockdown and my friend lent me his Volt. The only thing was my entry-level road bike was not compatible. Whilst I had my bike wheel off I thought I'd give it a little clean - MISTAKE! In short, thanks! This vid helped me get the back wheel back in its rightful place

Thank you Micheal. Its Xmas Eve and you saved me from having to present a Xmas present to my 8 year old that was unrideable. Lovely clear video. You have much more patience that I do! Thank you again and Happy Christmas!

I can’t remove the cassette, any suggestions? Thanks

Shimano tiagra is absolutely not 11 speed .

Thank you

"Going down the the beach with you Wi*# (what the hell am I saying) MATES!!!"

I’m clicking the high switch to change to a higher gear and it doesn’t go up what should I do

Thanks. This helps a lot.

Great video: I had a problem adjusting my brakes. I bought new pads and now there going to work like new and greased the brake pad levers.The grease was dryed out.

thanks 4 the video. what about the case when the arms work fine when u pull the lever but tilt (and don't recover) when u push in on one side? the other side recovers (pulls back from the rim) but the first side doesn't. i tried micro-adjustment screws but it didn't help.

Thanks

Lovely bike

Are we suppose to lip read

Thanks.

Thank you so much! My brother just gave me a bike, but the front brake isn't working well. I'll give this a try tomorrow!

Great video thanks heaps. Cute how 6m46s 6m51s was obviously mean for cutting room floor :)

good review

Good video! Simple and succint.

4 thousand views after 7 years :( well im here to give you love muah

Just a 90s mtb with 29er and 10x pricier

Great video, thank you. But I believe your levers are connected reverse of what they should be. Right lever/right shifter = rear brake/rear derailleur.

Well done. Many will be grateful if you make more. Thanks!

No way I can’t believe there’s a video on this bike I have the same bike and I love it even though it’s really old it rides like a dream, I’m 13 and it used to be my dads bike but he doesn’t ride it so now it’s mine it’s crazy to see all the extra parts on it that I took off lol

Tengo el mismo hermosa nave 😍