My Nomad Travel Life

Пікірлер

@tomasmowery164 Ай бұрын

Your Kobalt Impact is a step lower than Dewalt. I bit the bullet to get a Snap-on gun but that's a $1,000 gun.

@HaroldWhitmore-b8h Ай бұрын

Thank u”😊

@JamesWHurst 2 ай бұрын

I appreciate your making and sharing this video. Excellent work. Was there a reason that you didn't say what to torque the bolts to? Did you not use a torque wrench?

@kevinsheffield2110 2 ай бұрын

Thanks for this. did it and it worked!

@jorgemenendez5794 2 ай бұрын

👍 nice

@andrewflath6916 3 ай бұрын

NO! My debts are stuck on NORM A/C. I can't get my vents to turn to defrost. Do you know how irritating it is to constantly have air conditioning blowing? How do I fix it. I'm dying here.

@TheCC89 3 ай бұрын

When using battery impacts, using 1/2" adds a little more weight to the gun torque slap. Example, a thicker 1/2" drive impact socket versus a thinner 3/8" drive socket. Hard to believe that subtle change will make a difference but it does.

@garynemens4892 4 ай бұрын

I have a 06 E450 and the heat blows on the floor all the time. It burns my feet through shoes. Would this help that? It's like the floor heat is on all day

@SMYDA 4 ай бұрын

Another even cheaper fix is to remove the access panel on top of the dash and just tie the servo that controls the ac doors in the open position and call it good. You’ll won’t have access to the heat and defrost vents anymore. It’ll be 100% dash, but if you’re in Florida like me, who cares. 😂

@coco9004 4 ай бұрын

I have a 2003 E-450 super duty with Aluminum box truck but heavy loaded permanently. with ABS 6 wheels disk brakes. I need replaces calipers, pad and rotors. I was wondering if it is better to buy original from Ford Dealer or if there is better Brake kits aftermarket?

@goactivemedia 4 ай бұрын

I got everything from Napa. its been many years now that I did all that and still going strong.

@coco9004 4 ай бұрын

@@goactivemedia I am very happy to ear that! I will try Napa

@sergeruiz3032 4 ай бұрын

OMG shut up!

@jogapaul 5 ай бұрын

Best video for my situation tryout everything but problem was vacuum control

@TattedTommysTv 5 ай бұрын

so glad to have stumbled into your page i have a 97 but our problem is its stinking up everything like exhaust fumes and leaves all our guest skin stinkin .. Do you know if theres a valve to turn off when runnin ac in the rear ? or any idea why it stinks like exhaust in the back

@TheDogsBox 5 ай бұрын

Using a foam rubber waterproof tape instead of caulk or sealant will allow you to remove the panels when you are trying to pull wire, add systems, or repair things on your ambulance.

@universaltires8530 5 ай бұрын

I GUESS YOU SKIPPED REAR BRAKE CLIPS (HARDWARE)

@randyjluna3737 5 ай бұрын

How do I get the parts I need

@tomcindyhenderson1380 4 ай бұрын

Try Vantage optics, they sell a kit. You also should be able to get a generic reservoir from any auto parts store. The vantage optics also has a how to video.

@JDL_MobileRepair 5 ай бұрын

I knew I didnt want to do this job after purchasing an E350.. but I must since its scraping bad

@mikeobrien5867 6 ай бұрын

Hi, Thanks for the video! Is your Cyclops still working? Would you install it again?

@goactivemedia 6 ай бұрын

Yes it is still working and on the original battery still for a few years now.

@johnk125 6 ай бұрын

Thank you for this helpful video. I would know how to replace the pads & caliper but not the rotor. Now I am going to change all the parts confidently by watching your great video & explanation.

@Fredzfro 6 ай бұрын

YOU SHOULD HAVE CLEANED THE AREA WHERE THE PADS TOUCH THE ANCHOR. THERE SHOULD BE CLEARANCE ON THE EDGE OF THE PADS INSTEAD OF HAMMERING THE PADS IN. YOUR BRAKE JOB WILL NOT LAST AS LONG AS IT SHOULD.

@goactivemedia 6 ай бұрын

I made this video years ago back on Apr 30, 2021 and I am still using the brakes I put in. They have lasted for years now with no problems. We drive the truck 4 to 5 time a week driving to jobs for our business.

@renfruch2488 6 ай бұрын

😊Thank you

@randy1203 6 ай бұрын

Any idea what you tourqed those lug nuts at?

@rogerjoseph2532 7 ай бұрын

gtreat job

@levijudahmaqabim7123 7 ай бұрын

I did everything you said but no air comes out the front at all now. Only hot air in the rear.

@timmydukez9211 7 ай бұрын

DONT GREASE THESE. USE GEAR OIL NOT BEARING GREASE.

@davidkelly7485 8 ай бұрын

Mentioning part numbers of the replacement parts would be of some help.

@davepeters360 9 ай бұрын

WHAT? NO BRAKE LUBRICANT!! NOT A GREAT BRAKE JOB!!!

@treybo333 9 ай бұрын

What spindle tool is that for the axle? Any part number?

@robbietaillon7819 9 ай бұрын

There is so many things wrong with this video, that’s not how you pack a bearing ,that is not bearing greases ,that’s not how a bearing endplay is set and most importantly it’s an oil system not grease now oil and grease will be mixing so please no one do any of this .

@dangerdavefreestyle 4 ай бұрын

i agree with setting the bearing as i have the official ford book for that and it shows a procedure with a few steps he missed including measuring how much force it takes to spin the hub but im willing to bet he is driving it just fine and im grateful for a video of this quality that puts everything into perspective. his grease is fine everybodys a packologist, it just has to fully be embedded into the crevices perhaps till some comes out the other side.

@ansonwill1999 9 ай бұрын

Why didn't you put a new wheel seal in it am I missing something

@troysalmon6439 10 ай бұрын

Easy man thanks

@Miner-49 Жыл бұрын

Most of the time you can disconnect the vacuum line on top of the dash. Then spray just a tiny amount of WD-40 into it and reconnect. It has worked on 3-4 vans that I have repaired and my own. Long as the actuator/actuators aren’t bad. Otherwise this is a great down and dirty work around.

@pattianderson3926 7 ай бұрын

I'd like to try your method first, which line on the dash do I need to spray wd 40 into? Which color or location? Thanks.

@randypeer376 4 ай бұрын

Did it work for you? I have the same problem, mine is intermittent right now, if I cycle the knob from vent from air to vent i eventually get it blowing thru my front vents again. It works for 15 then quits and I have to recycle..

@enriquelopez9124 Жыл бұрын

Awesome information, and when you think how much it would cost to have it brought to a place where they work on A/C systems , plus the parts you can get real cheap

@ThePartyanimal3200 Жыл бұрын

parts list would be helpful

@bobrossi1185 Жыл бұрын

Do you know where little spring clips go ?

@hirenpatel9094 Жыл бұрын

I bought the $32 kit from Vantage Optics and air is working great here in Florida for my 1997 E350

@CharlieRoamin Жыл бұрын

Good vid - clean ! No BS/wasted time ! I'll be referencing this vid to do my new-to-me Winnebago C class motorhome . Thanks ! Did you use a manual for torque settings ?

@uzis4life Жыл бұрын

If anyone knows can u tell me the Cost of this job for the hardware and both hardware and labor if i would send it somewhere please

@isorozco511 Жыл бұрын

For the E torx heres a tip. Get a map torch from home depot (not expensive) and heat up the hub in the area that the torx bolt goes into. Not the rotor, just that sleeve shaped part along the sides. This loosens the grip and lock tite on the torx bolt threads and makes removing it much easier.

@jamesfarr5341 Жыл бұрын

Where's the rear clip go

@dosha1whip861 Жыл бұрын

I watched this and your video made me think the brake ripped me off. They charge me for the rotor but did not put it on. Good video

@flyngoat6681 Жыл бұрын

Thanks for the info ❗I Didn't know the pins held it all together.👍👍👍

@larrykroy9969 Жыл бұрын

Really should lube those pins you pounded in

@malcolmpoindexter8522 Жыл бұрын

Just what I was looking for. Thank you very much!!!!

@HarveyLangham Жыл бұрын

Fantastic video, solving my current a/c not blowing out the dash vents problem, on my recently purchased 2009 E350 cutaway bus. Your parts list is a great time saver for me. Thank you for creating the informative video and parts listing

@goactivemedia Жыл бұрын

Glad it helped

@drostly3220 Жыл бұрын

why do you grease the bearings when they are bather from the read diff fluid that floods the axle and washes out the grease and changes the composition of the rear diff fluid after the mix up.. ?

@natbrace220 Жыл бұрын

Thanks for the video! Helped me fix my 1998 Ford E-con Club Wagon A/C. Symptoms were exactly as you describe. Thanks for the post! Nat 🤩

@chrisanderson7844 Жыл бұрын

Thank you so much for this video. Very well made sir.

@maverickmonack195 Жыл бұрын

Bro who thought you how to pack a bearing cause that's 100% not how to pack a bearing and makes me question your whole video. Learn to do it right before making a video

@goactivemedia Жыл бұрын

Been driving it a few times a week for over two years now after I did that with no problems. I learned how to it from watching other videos from Auto shops that show how they do it.

@EddieFunderburk-ks5id Жыл бұрын

EXCELLENT!! Thank You!!

Ең жақсы KZbin

Пікірлер