What size belt you use or part number if you have it, I too am doing the hellcat front timing but to my 5.7 with a 2.7 hellcat snout pulley. I was thinking use the stock hellcat one as the adapter raises the supercharger and it should make up for the smaller pulley.
@MostWanted392z18 күн бұрын
What Do I need to start off, I plan to get the supercharger Can I just put it on>
@srtlopezАй бұрын
Hellcat heads ?
@1badcaddy1Ай бұрын
I was running 6.4 heads with supercharger adapters plates .
@MostWanted392zАй бұрын
@@1badcaddy1hey what would I need, does the supercharger direct fit on or will I need something
@dvii24dd2 ай бұрын
Who did your swap
@1badcaddy1Ай бұрын
I do all my own work . Motor , body and paint
@dvii24ddАй бұрын
Wy located
@hectorguajardo63922 ай бұрын
It also look like you’re running front thermostat, housing, and pulley system off of the hellcat to make the supercharger to work because I saw other way and I don’t like it. The part that I need a hack off the front top part of the housing.
@marshalllapenta76562 ай бұрын
Hellcat super charger on a 392 with a STOCK pulley Something I'd like to do!
@Lestersrthellcat153 ай бұрын
How much we are about to spend in this protect ? 10k ??? That's awesome as long as you get that wine , it's all in
@anthonysams482522 күн бұрын
Who cars when you can make a scat faster then a cat
@Lestersrthellcat1521 күн бұрын
@@anthonysams4825Is that Sh* faster that a CAT ? You better put a Whipple 3.0
@Lestersrthellcat153 ай бұрын
I really love this Job .. I want to get a Charger and do it
@christ71993 ай бұрын
Hi, I just installed a new 6.4 hemi in my 2014 ram 2500 and was thinking about putting a super charger on it. Nothing crazy. Any thoughts?
@1badcaddy13 ай бұрын
Mmx just introduced a complete kit to make that happen . Keep the boost below 6 and you will be good
@dustinl69173 ай бұрын
What about the pressure relive valve is it not plugged in?
@sethbarnard76363 ай бұрын
Is that a midnight purple if not what color is it ?
@1badcaddy13 ай бұрын
It’s called black eyed . Most people know it as hellraisin
@adrianlong6240Ай бұрын
@@1badcaddy1more 6.4 content plz u almost made me do it 😊
@naseemjalil77204 ай бұрын
transmission?
@1badcaddy14 ай бұрын
It was an hp70 on sound German auto kit . Now it’s a complete hellcat swap
@naseemjalil77204 ай бұрын
@@1badcaddy1 okay deal‼️all i want is the supercharger whine, lowest possible boost on my 6.4L srt jeep. what all do i need to do. to the fuel injectors and all. what is all required. Please & thank you
@BabyRt4204 ай бұрын
Did you cut it
@BabyRt4204 ай бұрын
Nvm
@dustinl69174 ай бұрын
Did you use stock 6.4 oil pan with the hellcat timing cover?
@1badcaddy14 ай бұрын
You have to use hellcat pan for the front pan bolts to line up with front cover
@dustinl69174 ай бұрын
Thank you.
@sevrajsami4 ай бұрын
You sound like matthew mcconaughey
@Lestersrthellcat155 ай бұрын
I love it ...
@Lestersrthellcat155 ай бұрын
Do the whine is there ??
@rubengomez20055 ай бұрын
What’s your email I need help with mine
@petecruz39465 ай бұрын
I have a few questions
@seriouzfilmz93976 ай бұрын
I have the engine and the blower but trying to to piece together everything needed did you forged it?
@1badcaddy16 ай бұрын
Yes if you want it to last you need to forge it
@seriouzfilmz93973 ай бұрын
@@1badcaddy1I got the pistons now did you do the full hellcat timing cover or adapter
@1badcaddy13 ай бұрын
Hellcat front cover and oil pan. But that also requires hellcat waterpump and all pulleys and tensioner
@seriouzfilmz93973 ай бұрын
@@1badcaddy1 gotcha I have the pan but I don’t have the the timing cover. I have a 09 so I would have to upgrade water pumps and stuff anyways so I’m thinking of just getting the hellcat front end stuff
@chrisfoams6 ай бұрын
You were slippin my boy😕
@1badcaddy16 ай бұрын
That was a 5 speed nag 1 . It has a hp90 now
@ScorpioFPS6 ай бұрын
Can you do a video showing how she sounds and drives? Maybe do a pull or two as well?
@williamharris59576 ай бұрын
Good luck
@capitansuarez32316 ай бұрын
Do you have an email or Instagram. I have a 6.4 I’m trying to build
@mrwhamisrick7 ай бұрын
What does it cost to put a hellcat supercharger on a 6.4, inculding the tune?
@20yearsagoАй бұрын
A lot
@Alex-pl1ye27 күн бұрын
Flyin Ryan performance
@ktwosrt8life7 ай бұрын
Are you still running all-wheel-drive with a supercharger?
@keepitthoro67687 ай бұрын
aint that a taking time bomb....is thay safe to do.....
@John76_5568 ай бұрын
You think I’ll be good on a stock 6.4 running 6psi?
@1badcaddy18 ай бұрын
Yes on 6 you will be great . Run 93 octane
@John76_5568 ай бұрын
Think I should do drops ins first just to be safe
@1badcaddy18 ай бұрын
6 lbs on stock . If you do drop ins with rods you can push as much as you want
@John76_5568 ай бұрын
@@1badcaddy1 how you blew yours up?
@1badcaddy18 ай бұрын
Rod failed. Was running 14 lbs . Forged pistons looked great
@DarkHorseParatrooper10 ай бұрын
What exactly was needed to make the 6.4 accept the blower. Like a hellcat ecu, new wiring, splicing, etc?
@1badcaddy110 ай бұрын
I ran a hellcat front timing cover ,waterpump , lower pulley and oil pump . I used my 5.7 harness and my ecu. Remote tuned using hemifever tune . I did have to remove tape on harness to separate injector and coil wires . If you do this you will not have to splice .
@JewelSyde2 ай бұрын
@@1badcaddy1when using the hellcat timing cover do you have to also run the hellcat crank pulley? and will it work with the stock 6.4 crank ?
@WhatupdoeTV31311 ай бұрын
I’ve got forged internals on my R/T 392 swapped Durango but I was thinking of going the turbo route. Now I’m thinking of just getting a Hellcat blower since they only put out 5-6 lbs of boost on the 6.4. I don’t want to get too much boost for my daily driver.
@1badcaddy111 ай бұрын
You can get more boost with a pulley change . It will only cause you trouble asking for more than that . I blew mine up and have a hellcat motor now .
@deltazulu39210 ай бұрын
@@1badcaddy1How hard was the hellcat engine swap from your scat?
@1badcaddy110 ай бұрын
@@deltazulu392 I was running the hellcat motor on a 5.7 harness . Just need a good tune. Mine was a hemifever remote tune.
@Zip3k8 ай бұрын
how long did you have this setup before the motor blew? I have a 2020 scat, thinking about ordering a 3.0L whipple, i have a shop 5 miles from my house that specialize on mopar @1mopargearhead
@devriontapowell890211 ай бұрын
Do you have email we can contact u from
@1badcaddy111 ай бұрын
What can I do for ya ?
@domoniquedrummer43352 ай бұрын
@@1badcaddy1 yo so I have a stock 6.4…. I can just get a stock SuperCharge and slap it rite on, without blowing my motor??? Or what else needs to be done
@Valid.4l11 ай бұрын
How reliable is it and what’s the max amount of boost can you get out of it?
@1badcaddy111 ай бұрын
I did a pulley change and was pushing 12 lbs. I ended up blowing the side out when a rod failed .
@Valid.4l11 ай бұрын
@@1badcaddy1 they say they don’t take boost well but I’m pretty sure that if you build it right it can handle anything. At least that’s what I thought
@Valid.4l11 ай бұрын
@@1badcaddy1 10lbs is more then enough I’m pretty sure your either faster or right next to the hellcats but correct me if I’m wrong
@donsonbr Жыл бұрын
Great work, but Im not feelin' the green wheels.
@busterc6600 Жыл бұрын
I'm going the expensive route through direct connection with my 1320 scat bro. Nice set up
@dretookoff Жыл бұрын
Does it whine?
@SRTyler392 Жыл бұрын
Can you just run the hellcat pulley and just get the 5lbs of boost without forging the internals?
@1badcaddy1 Жыл бұрын
Yes you can but the front cover and oil pan also has to be changed to run the hellcat pulley setup
@SRTyler392 Жыл бұрын
@@1badcaddy1 ohhh alright so it’s probably cheaper to just run the hellcat supercharger then huh
@Freddy_Confetti Жыл бұрын
Stock air intake is shocking
@shaneonews6791 Жыл бұрын
Good luck with the bottom end of the engine.
@mrwhamisrick7 ай бұрын
The bottom end isn't the weak point.
@shaneonews6791 Жыл бұрын
Wrong. The 392 bottom end is maxed out in stroke. Which can't handle the higher power of the hellcats, red eye etc. Thus is why Dodge uses the 6.2 not 6.4 .
@jamesbraxton53398 ай бұрын
tuning trans etc its not just one thing making it all work. but yeah the pistons were not made for boost or very low only less than 5
@javiermendoza7523 Жыл бұрын
What is everyone doing about the inner fender liners?? Been struggling to get answers and I haven’t been able to get any
@1badcaddy1 Жыл бұрын
I’m running OEM inner fenders . I done another car and used the filler panels that come with the Ikon kit do a great job !
@jameschilemi4690 Жыл бұрын
Looks clean as hell. What size rims/tires do you have?
@1badcaddy1 Жыл бұрын
295/30/22x12 on rear and 265/35/22x10 on front
@catfishkam Жыл бұрын
can i run stock pistons and just all around stock motor with the supercharger on top with 6lbs of boost?
@1badcaddy1 Жыл бұрын
Yes you could get away with 6 lbs . The problem is you will want more . I put a smaller pulley on mine and blew the bottom out !
@catfishkam Жыл бұрын
@@1badcaddy1 so how much hp do you think i’d have after the blower on top? i think i’ll keep the stock pulley for now. i wanna have completely stock internals with the 6lbs of boost.
@1badcaddy1 Жыл бұрын
@@catfishkam should be around 600
@catfishkam Жыл бұрын
@@1badcaddy1 how much boost can the motor handle stock? i want it to be fast and keep up with a lot of stuff but i want the motor to last me.
@GloomToon4 ай бұрын
@@catfishkam392 motors suck when it comes to handling boost. I’d run 5lbs of boost just to be on the safe side
@milaperegon2787 Жыл бұрын
Hello, did you use Thicker gasket to lower the compression ratio?
@1badcaddy1 Жыл бұрын
No I didn’t change compression.
@milaperegon2787 Жыл бұрын
Thanks, do you have 4032 drop in Pistons and Manley rods ?
@1badcaddy1 Жыл бұрын
I had forged piston but I ran stock rods. It held up until I changed pulley. If your gonna due piston definitely do rods !
@milaperegon2787 Жыл бұрын
I'm replacing both rods and Pistons. Im little confused between 4032 and 2618 pistions. What pistions did you get? Could you please share the link? You car looks very clean.. Nice build bro 👍🏾
@seriouzfilmz9397Ай бұрын
@@1badcaddy1this was something I was going to do I have the pistons but wanted to skip rods this helps lol
@fleejr55 Жыл бұрын
where are you located?
@FranciscoHernandez-dq7rf Жыл бұрын
Nice set up man looking to upgrade my scat once warranty it’s done lol but will see what’s up wish we could upgrade this hemis more N/A power close to the 600 that would be great
@SRTGHOSTS3 ай бұрын
You can but it’s costly, I did a 454 stroker: it’s making 600hp crank but can handle another 250shot of nitrous. Another guy did same mods as me but had a high ram he has making 615 wheel and it’s over 700 crank
@ShawnWickGaming Жыл бұрын
Thats nasty 🔥
@ShawnWickGaming Жыл бұрын
Nice build homie
@Jeff-ej4wp Жыл бұрын
Add a supercharger and use stock air intake? Get a cold air intake bro.
@1badcaddy1 Жыл бұрын
Lol. Most cold air intake give you hot air! Superchargers don’t work well with hot air ! That’s a hellcat air box sucking cold air from lower bumper vent .
@Jeff-ej4wp Жыл бұрын
@@1badcaddy1 Get a cold air intake that is isolated from the under hood hot air bro. Don't buy any of the cheap made in china crap.
@jlopezesus Жыл бұрын
@@1badcaddy1 I've noticed alot of non Mopar fans when they see the Mopar engine bay on scatpacks and up they think the first upgrade would be a CAI but ours is actually pretty good already and hard to improve on aftermarket