hi, i have a question, i have this headlight , Vectra c afl xénon, and i have a crazy problem: the left low beam has started bliking sometimes on bumps ans Bad roads, then it has stopped working, with dash light on. i put a New bulb, that didn't worked, i replaced the ballast, then my left low beam worked again.. but when i finished put everything black, screws, bumper.. and closed thé car... the left xenon is still on.. with car locked.. it nevers turns off... even 10 minutes later.. it's still on.. if i turn headlight Button, the right light turns on off, no problem, but the driver side low beam is always lightning.. do you have ever sée somerhing like that? do you have an idéa ? i had to remove balast to save the battery.. best regards.. al
@xenonland6 күн бұрын
I've never heard something like that before.
@keja0016 күн бұрын
mee too, that's why i asked you.. do you know if the main 12v is aways send to the ballast even when ignition is off? or should it be at 0v? if i remove the ballast, plug tester on the 2 pins on the right (where ballast is ) and i have 12v.. Always.. no fuse or relay remove can cut this.. only disconnecting the battery stops the 12v..
@xenonland6 күн бұрын
@@keja001It seems that you check the possible causes. If lighting continuously it means that 12v is coming to the ballast without interruption, very strange. You know the switch inside should cut the 12v when off position.
@keja0016 күн бұрын
the Switch cut thé right one, but not the left.. Can it be the Switch? you think there are 2 12v lines coming from Switch to both headlight?
@xenonland5 күн бұрын
@@keja001 definately 2, but switch should cut normally both of them
@sebastianschrock46779 күн бұрын
Is the 177310-32 AA 544772965 compatible with 177310-32 AA 324406669? Thanks in advance :)
@ynesflores326110 күн бұрын
Best video by far. I love how you show the instructions using a headlight assembly. It made it so much easier. Great tip on using a flat tip screwdriver instead of a Phillips. It was much easier and better than another video I watched. Thank you!
@666ozzy8811 күн бұрын
How to replace turn signal light bulb??
@lamghariayman436112 күн бұрын
What do i need to do in order to switch from halogen to xenon on a vw mk5 gti
@kostaskounatidis764515 күн бұрын
How can you test if the Ballast unit it’s failed ? The ballast unit gives power to the D3S lamp ?
@budhead903515 күн бұрын
how many AFL AFS power modules are there on a pre-facelift Vectra? is it only on the right headlight the module
@aykutkolcu381115 күн бұрын
Hello, I have an OEM bi xenon headlight in my vehicle, I replaced it with a LED projector, how can I turn off the ballast,igniter malfunction light?
@tomasstanevski665816 күн бұрын
Hello :) can you send me link from where u can buy it :)
@kostaskounatidis764517 күн бұрын
How do u take it apart ? I have a huge problem with the headlight and they tell me to replace the hole head light
@xenonland17 күн бұрын
With the help of heatgun
@kostaskounatidis764515 күн бұрын
@@xenonlandI have the same headlights , can you just replace the xenon ecu without taking it apart ?
@xenonland15 күн бұрын
Yes, you can
@fernandoaparicioperez906919 күн бұрын
Hello, i have an afl problem. When i make the left abd right turns th h11 bulbs ignite the first time, but in a few moments both doesnt work. My mechanic says that i have a problem with the motor mechanism and i have to change headlight... What do yoy think? Many thanks
@Zedition21 күн бұрын
Hi, I have a 2006 e87 with weak headlights. There is light, but weaker than normal. Can this also be the ballast? I have tried to change both bulbs, and it did not get better. thanks. Great video.
@xenonland21 күн бұрын
No, it is not related to the ballasts, but with projectors. If your car is over 200,000 km, projectors usually get smoky inside.
@Zedition21 күн бұрын
@@xenonland Ok, thanks. So it would help to open up and clean them?
@xenonland21 күн бұрын
@Zedition it is not only about cleaning. If reflectors are peeled, then cleaning will not help. They will need re-chrome
@ecee_8821 күн бұрын
Are you from Turkey
@nvnoferreira21 күн бұрын
Hi @xenonland , can you please give me hand with these Cayenne ballast modules? My 2008 came with the original ballast on the right headlight reference 955.631.194.02 , but on the left side the last owner did install a new Hella ballast , reference 5 DC 009 060-01 . Is this new ballast ok ? Although there is the error on the Dash Main Menu that as you mentioned must be done at Porsche dealer with PIWIS software
@xenonland21 күн бұрын
5DC009060-01, as stated in the video, is NOT compatible, you have to change it. It can not be coded even with PIWIS. Only Hella 5DC009285-011 can be coded at these models.
@stefanciprian428025 күн бұрын
Foarte bine explicat🎉
@whitedog30326 күн бұрын
What is the other bulb on top...i can wan to buy all the corect bulbs and do not want different colour halogen bulbs
@s7aaa727 күн бұрын
Today I changed mine the back covers from both headlights because the mechanic broke it all 4:( never told me just I find myself when I was washing my car was getting water inside:(( the right headlight insede the window is with water stains :((! So when you replace the cover be careful with the jake is so easy breaking it:(!
@s7aaa727 күн бұрын
Hi The big cover where is the high beam d1s bulb they have on each side screws?
@scseposcashregisters94929 күн бұрын
Turn the music down so we can hear you speak in your videos, rather than the music
@xenonland29 күн бұрын
Thanks for the feedback, now should be OK (minimum level selected).
@halilyou1985Ай бұрын
Is it possible to open the part shown at 12:34 by unscrewing only 3 screws? Is it necessary to perform a sealing operation when closing it afterwards?
@xenonlandАй бұрын
This led module has its own seal. Just fasten the screws
@halilyou1985Ай бұрын
@@xenonland Thank you very much.
@mayahristov8852Ай бұрын
Thanks for the video! Very informative and to the point! The low and high beams on my 2006 Z4 are working, but the hallow ring on my left headlight is out. Is this fixable by replacing a bulb, or do I have to replace the whole headlight?
@xenonlandАй бұрын
Just replace the bulb
@z-_supratm-9215Ай бұрын
Thank you for the video. So, if I understood right, I need to buy a DRL module that has the same ending letter as the original DRL module installed on the car? (The D letter in your case) I have a Octavia MK3 with the right headlight DRL not working. Thank you very much!
@xenonlandАй бұрын
Yes, correct. If problem not solved after fitting the working drl module, it means that the LED "bulb"/aluminium body is faulty.
@A8D92Ай бұрын
I recently had an igniter fitted but it burnt out because it came loose. I went to fit one myself, but when I turn it, it doesn't lock into place. As in the 4 tabs that go into the metal ring, it doesn't snap into place when you turn the igniter to 12 o'clock position. Any ideas? The white indents inside the igniter are lined up and goes in, I am also able to connect the wire after it turns to lock position, but with the slightest touch it comes loose.
@petermoore2429Ай бұрын
Thank you for your videos, the question is, is only the reference AL1307329058 valid for the Golf 4 GTI or would others be valid?
@xenonlandАй бұрын
There are other numbers but the key is the cable length and 3-pin configuration. Most of the 3-pin igniters does not have long enough cables for Golf 4.
@petermoore2429Ай бұрын
@@xenonland Ok, could you tell me any other valid reference for golf 4?, thanks for helping me.
@73SeddikАй бұрын
Sir Do you have the part number of the AFS module for Skoda Yeti 2011. Thank you in advance. Regard
@xenonlandАй бұрын
Skoda Yeti 2011 doesn't have separate AFS module, it has ballast unit which also commands the AFS function. AL part number is 1307329120
@73SeddikАй бұрын
Thank you very much. Bless you 🙏
@73SeddikАй бұрын
Thank you very much
@xenonlandАй бұрын
You are welcome
@perskjelbred7099Ай бұрын
Annoying music!!
@xenonlandАй бұрын
You are right, but all copyright free musics are like this :)
@dimitrovhariАй бұрын
Mercedes is a garbage car for me
@mikejames2571Ай бұрын
Thanks for the video. My problem is the led strip light across the bottom which went intermittent but then failed. The side light in the centre is still working but not the led strip at the bottom? This is only on the drivers side. I assume something needs replacing but I don't want to take the whole bumper off to' see that I can fix it without removal.
@xenonlandАй бұрын
either your led module is faulty or the led "bulb" (aluminium body inside the headlight) is burnt. First one is replaceable, second one is not (unless you remove the glass).
@mikejames2571Ай бұрын
@@xenonland Thanks for the comment. How do I get at the faulty module? It seems the side light in the centre is unaffected. Is it road legal to leave the strip as is?
@27NakuАй бұрын
If the ballast is burned, is that sound still heard when you turn on the headlight? My light bulb doesn't work, but you can hear that buzzing sound in both headlights. The one on the left works.The one on the right after an accident, it was cracked, it made condensation, the bulbs blinked in unison for a few days until the LEDs (daylight) and the xenon bulb stopped working. Only that bulb works when you make a curve and the signaling.What could be the cause? The errors on the board are the following: Check right dipped beam lamp and Headlamp levelling malfunction - contact service
@stbmw5735Ай бұрын
Mine is 2013 and unfortunately has another system much more difficult than this
@ochtipsetАй бұрын
Hi! Thanks for providing great content. I have a MK5 R32 with bi xenon headlights. My left headlight is having an issue with the shutter that opens up when I turn on full beam. After 3-5 seconds the shutter closes. So you have any idea about what I need to do to get my shutter to work as it should do?
@user-zi8hi8yu1rАй бұрын
Hi thanks for this video! Just a question, what is the socket type for the 5w5 bulb? Mine have burned but I don’t know where to buy them
@xenonlandАй бұрын
These are not sold separately from Mercedes-Benz. You have to buy donor headlight. Or you can buy here: www.ebay.de/itm/276382764483
@user-dalasАй бұрын
Hi, i have opel Vectra c 2004 and we trying to repair the light. But we dont know where is the problem. Whole light work. Only the left headlight doesnt work. We tried to connect left light to connector to right and it works. But when we connect any light to the left every light work only the Main light doesnt work( turning light work, light when you turn the wheel work, the light for night work[the blue one] the light for when you stop works] only the day light or how its called doesnt work. We tried to use multimeter but it seems the power is comming to the light. But the light for day does not work and we dont know why where is the problém please?)
@user-dalasАй бұрын
(Its the bottom right light) in 0:55 Sec in your video.)
@papsu67Ай бұрын
The best video how to do the change of xenon head light bulbs, THANK YOU!
@xenonlandАй бұрын
Glad it helped!
@zilla4593Ай бұрын
Great vid! Would I be able to use a holesaw with a drill to remove DLR headlight grommets?
@xenonlandАй бұрын
Yes, absolutely
@KorashSyndikatАй бұрын
The lens was never touched by you, was it? The lens is the glass object that covers your D1S Xenon Bulb, my friend. Do you have part numbers for the replacement sockets?
@hardcleАй бұрын
I have a 2006 Passat. I have an AFS fault on the dashboard . Right side headlight comes on then goes out. Are both the ballast and the AFS bad or is a problem with one causing the other?
@xenonlandАй бұрын
Ballast is only for the low and high beam. If the low beam works and you have AFS fault only at the dash, more probably your AFS module is faulty,
@slawomirsiwinski2 ай бұрын
Great video you doing mate everything is clear and good explaining💪👍. I live in England, I bought a car after an accident with category unfortunately it was hit in the front. the lights jump slightly, the mechanic found the cause, the lamp mounting clips are broken, how can I fix it, please help
@xenonlandАй бұрын
if you mean the fixing tabs that are used to attach the headlight, then they are sold separately by VW as REPAIR SET for headlights/
@slawomirsiwinskiАй бұрын
@@xenonlandThanks mate 😃
@caseytrader2 ай бұрын
Very clear instructions, thank you
@xenonlandАй бұрын
You are welcome!
@thehooliganvideo73092 ай бұрын
Whats the name of the white plastic clip. I've broken it and now searching to find a replacement.
@xenonland2 ай бұрын
We call it "nest", but it can be holder, bracket etc.. this is not sold by VW as separate part, hence everyone calls it something different
@Joeyizme12 ай бұрын
So many ads in BS I can't even maximize this and turn my phone sideways. Marketing over the top. Information minimal.
@xenonland2 ай бұрын
Minimal information? State just 1 missing info regarding the xenon system of these headlights?
@dariusgaldikas88932 ай бұрын
Hello i got 2 faults one is Left Swivel module position sensor faulty (02629), and instrument cluster no singal/comunication (01317). Could this be the problem that my headlight shine a bit low ?
@xenonland2 ай бұрын
02629 causes inaccurate positioning of the projector
@dariusgaldikas88932 ай бұрын
@@xenonland so this could be the problem why my lights shine not so bright or it doesnt make a good beam ?
@xenonland2 ай бұрын
@@dariusgaldikas8893if your beam is not bright enought, and your car milage is above 250000km, then most probably your projectors are internally cloudy/smoked.
@SwipesYT2 ай бұрын
Would you be able to make a video showing how to replace the h7 high beam bulb?
@huntermercedes45572 ай бұрын
Здравствуйте!! Посмотрел ваше видео,вы занимаетесь светом авто?? Если да,то подскажите ,если убрать перегородку в фаре Купер r50 рефленая перегородка стоит в ближнем свете ,будет ли свет нормально и ровно светить?
@felit99912 ай бұрын
Thank you so much! It’s so hard to take them out! I have a question, does the base model of e320 2004 w211 have these? I wanted to look but it’s so hard to check. I guess all I have to do is check if it has the igniter on the back? Also what do you think of the LEDs? I feel like cars with them blinds oncoming traffic. Or even raised trucks behind you at stop lights.
@xenonland2 ай бұрын
The base models also have Xenons. Yes, when and if you remove the rear cover, if you see any igniter (black or silver), then you have xenon headlights. If you have only H7 bulb, then you have halogen type headlight
@felit99912 ай бұрын
@@xenonlandthank you
@void3082 ай бұрын
Thanks for the video! Informative
@xenonland2 ай бұрын
Glad it was helpful!
@mandlatambula17472 ай бұрын
For angel eyes, should i remove the whole headlamp?
@xenonland2 ай бұрын
Not really, remove the rear cap and you will have enough access
@ronnystegenborg78202 ай бұрын
Thanks 🙂 i have been at a mekanic they tryed to set my right bulb fast, cause wa only sitting loose, from former owner, i just see cause i was looking for LED Light, buut they had trouble and could not get it to sit, and said bumper needed to get off... hmm today i looked again ur video and i now got the bulb to sit right and the one inside was big problem but i now got it in and could turn it little and it sit now and lights more white then b4, and i got it without take the lamp out :-) so not so hard when you first know how to set bulb and holder, left is not so easy i haven´t looked on that yet but i have too it light more yellow then white so maybe that is loose too, i have see i maybe can do it from under true left wheel, i hope not like to remove bumper 😛