Really helped searched a ton of videos no luck but yours was dead on thanks bud 👍
@joeybalogny609510 күн бұрын
Glad it helped.
@joshua7martinez15 күн бұрын
Thank you for the video. Great info. For a new install I think this would be a great option, the flush mount. But there are times were surface mount is also a viable option, such as panel upgrades. Where time/money difference is not worth it just because of the aesthetics. But I do agree it looks nicer.
@joeybalogny609515 күн бұрын
It does look nicer most of the homes in my area are using gas for stove hot water heater 200 amps is good for most but the larger homes I do install 400 amp panel with a sub panel.
@joshua7martinez12 күн бұрын
@@joeybalogny6095 And do you install those 400 amp panels flush, or surface mount?
@joeybalogny609512 күн бұрын
The 400 amp if overhead service are surface mounted but on underground service you can stub up just inside the form board before they pour the pad I install the panel support it so the framers can frame around it underground service is always flush mounted.
@nickl883023 күн бұрын
Good stuff thx for the info
@joeybalogny609522 күн бұрын
No problem 👍
@scotts.447129 күн бұрын
Code violation to run romex on face of stud plus no supports running across attic
@joeybalogny609529 күн бұрын
some of that romex was done from previous homeowner I staple my romex that is code in our area nec 336-18 romex support within 12" of boxes 4 and half foot inervals through holes in studs rafters I understand what youre saying but not every job is perfection or within my control of what was previously done if u think jobs are perfect please tell me how.
@5.0mike33Ай бұрын
Thank you man!!
@joeybalogny6095Ай бұрын
No problem!
@Montasser333Ай бұрын
what will tell you about air conditioner ?
@joeybalogny6095Ай бұрын
It does ac controls.
@vcronaz30Ай бұрын
Gangster af thank you 🙏🏽
@joeybalogny609510 күн бұрын
Right on glad it was usefull
@LewandowskiDamianManagerАй бұрын
Cold engine or hot?
@joeybalogny609527 күн бұрын
I grew up with a diesel mechanic dad so we usually would check oil with a warm engine you usually get a better level reading.
@bancseason7138Ай бұрын
Thanks!
@joeybalogny6095Ай бұрын
No problem!
@MegaMan-bs3oyАй бұрын
I changed the purge vavle cleared the check engine light but still get the code if I check. :/ something else?
@joeybalogny609510 күн бұрын
glad it was of help.
@bankroll716Ай бұрын
Thanks!
@joeybalogny6095Ай бұрын
No problem!
@got2boostit2Ай бұрын
Looks like Drivers side to me. But thanks.
@pstreetgarage73042 ай бұрын
Great description
@joeybalogny60952 ай бұрын
Thanks!
@solairegun46672 ай бұрын
So it’s just a black wire just red
@joeybalogny60952 ай бұрын
Its 120 volt hot wire used for maybe half hot 3 way/ garbage disposal dishwasher will have a split outlet red and black so red is switched garbage disposal red is 120 volt hot.
@user-jw7st1kf9l14 күн бұрын
Ooo so like extra push of a current
@joeybalogny609514 күн бұрын
Its a hot so its say for example garbage disposal dishwasher you would need the black for dishwasher and the red for garbage disposal or a fan the black would be for fan the red for the light on the fan.
@PapiSalazar-mp7lw2 ай бұрын
I got the same code coming up in the 2015 mustang. The problem with mine is that it stalls after putting gas.
@Dice10212 ай бұрын
MINE TOO 😮😮
@joeybalogny60952 ай бұрын
Low pressure sensor
@steveshuss7382 ай бұрын
my 2002 pulls a 0455code if the gas tank goes to 1/2 tank or below if i don't let it go below 3/4 it never seems to come on you think it would be the fuel tank pressure sensor? i mean it's not biggie i just reset it been doing it for 3 years now lol but if i could no for sure i would attempt to fix it
@joeybalogny60952 ай бұрын
Low pressure fuel sensor is usually a cause.
@joeybalogny60952 ай бұрын
I like that idea marking the wires that will help with anyone that gets into that panel.
@ironmartysharpe82932 ай бұрын
Thank you Joey , It's especially important on circuits that use two different wire sizes such as 12 and 14 gauge wire , I'll take a piece of white electrical tape and write on it , Do not exceed 15 amps and put it on the wire in the panel and you are absolutely correct on sizing the breaker for the smaller wire size to be code compliant , two years ago I was visiting my younger brother and I noticed that he had a small fuse box in the garage that has screw in fuses and was fed from the breaker panel So looked at it and found 30 amp fuses in there and pointed it out to him and opened up the fuse box and checked the wire gauge coming off each fuse and sure enough the wire gauge was 14 , and I said to him that you absolutely cannot exceed 15 amps because of the wire gauge and showed it to him with the fuse box open and by putting 30 amp fuses in there , You have no electrical protection and can very easily start a fire Another thing is that parts of his house has knob and tube wiring and it's very rare that you'll find 12 gauge wire in knob and tube wiring , So at least he understood the danger of a fire by using 30 amp fuses and I got rid of them and put 15 amp fuse in there Not once have I come across a fuse box that had the right size fuses in there and change them out and put in the right size fuses
@ali055637782905563772 ай бұрын
Im still don’t which sensor is damaged cuz the computer said problem to the bank 2 but which sensor
@massimo12922 ай бұрын
Same here, idk what to do lol
@joeybalogny6095Ай бұрын
Youre looking at a code that may be youre ecm if the car runs great I wouldnt worry about it sometimes anything makes a check engine light some are difficult to figure out im going threw this silverado its tough 18 errors on the ecm but the truck runs great.
@ironmartysharpe82932 ай бұрын
One day , Me and this one ladyfriend of mine went to her daughter's house to replace a few receptacles that were bad and install a ceiling fan in the master bedroom , when replacing the bad receptacles , We found 12 gauge wire coming from the circuit breaker panel to the first receptacle in the kitchen because we had to find the first receptacle to replace it with a GFCI receptacle to GFCI protect the other receptacles on that particular circuit using the load side of the GFCI receptacle , But anyway , We found 14 gauge wire going to the other receptacles and it had a 20 amp breaker in the breaker panel , We have also found 12 and 14 gauge wire on two other circuits , So when I pointed it out to my ladyfriend , She definitely agreed to replace those breakers with 15 amp breakers and exactly like you said , The circuit breaker has a be sized to the smaller wire , So we opened up the breaker panel and replaced the breakers , Whenever I go into a circuit breaker panel , As standard procedure , I go over the entire panel and inspect every wire for signs of overheating and I take my insulated screwdriver and check every connection to make sure it's tight and found a couple of loose neutral wires on the neutral bar and found one ground wire not connected , I explained to my ladyfriend that whenever you go into a circuit breaker panel , Always check all the wiring in the panel and using an insulated screwdriver , Check all the connections to make sure they're tight , And make that a standard procedure for yourself as well and she said she'll do that from now on , My ladyfriend has alot of knowledge with electricity and if she's doing electrical work and not sure of something , She'll ask me Yes , I have found loose connections in other breaker panels and took care of it and that's why I made it a standard procedure whenever I go into a circuit breaker panel Also whenever I find 12 and 14 gauge wire being used on the same circuit I mark the wires in the panel Do not exceed 15 amps so if somebody else happens to replace that breaker , Not to exceed 15 amps
@ethanortiz93393 ай бұрын
How would you check your ga tank thingy I have those spring gas cap things and idk how I would check if that’s the issue
@joeybalogny60953 ай бұрын
Is your flapper closing all the way.
@Fiveohgofast3 ай бұрын
Thank you sir! Helped out a lot!
@joeybalogny60953 ай бұрын
Glad it helped!
@carlosarmero5943 ай бұрын
I lit a strike anywhere match and proceeded to dump it in the filler neck and no more dtc…. People I’m playing around please don’t do this….Now seriously good video sir perfectly explained.
@JohnThomas-lq5qp3 ай бұрын
We call your battleships Madison bars. Best pratice is to install long leg day on bottom then opposite side facing up to distribute load. If using traditional screw terminal devices ( switches & receptacles) best pratice is to apply several wraps of quality ( none of the cheating POS Chinese tape ) around them to.prrvent one of the legs from shorting out. Have come across the legs on Madison bars shorting out months or years after they were installed because person did not use the needle nose pliers liked you showed to get a tight bend. By the way Madison bars come in at least two leg lengths. In hospital elevator & fire escapes have encountered three sheets of 5/8" sheet rock and 2" thick guess three hour fire rated special sheet rock that regular Madison bar legs were too short.
@beatsbybri3 ай бұрын
Thank you!
@joeybalogny60953 ай бұрын
You're welcome!
@hadleyslife73513 ай бұрын
My 2000 just got this code. Looking for answers. This video is great.. never had to mess with the evap system before. I already checked the fuel cap. I’m gonna have to look up a diagram. I hate to think about it but couldn’t it be a rust hole in the gas tank? Just thought I’d mention it
@playerofawesome22 ай бұрын
Just had the same code come up on my 03. Im wondering the same thing. Only way to know is to take off the cover and visually inspect it. Or use a smoke machine like he said
@damienexplicit31656 күн бұрын
It could honestly, I have the same code coming up and my tank is a tad rusty.
@mnowland133 ай бұрын
2015 gt just threw a P0454. Any idea what the specific difference might be? This is the best and closest video I've found so far.
@joeybalogny60953 ай бұрын
PO454 could be a bad pressure sensor they are easy to change
@Skyy30003 ай бұрын
Very resourceful video 👏🏾
@joeybalogny60953 ай бұрын
Glad it was helpful!
@bsheen3 ай бұрын
I just came across your video while researching this issue for my father in law. You wouldn't happen to know of any places to get parts through? It's a 2003 mustang. I think it's the fuel vapor control valve assembly he needs. Apparently it's a discontinued part. He cannot find it anywhere.
@joeybalogny60953 ай бұрын
A1 AUTO parts or parts geek should have one a 03 you should be able to find one
@bsheen3 ай бұрын
@@joeybalogny6095 I will check them out. Thank you!
@educationaltvshows99504 ай бұрын
How it compare to Launch 919 BT? Faster hardware and ECU coding. Quite similar price..
@nunyabinnis40694 ай бұрын
i have a 2013 mustang gt 5.0 with the boss 302 intake manifold, recently its been stalling when driving shifting out of gear into neutral. could this cause the stalling? also the idle is low like 600 or under
@joeybalogny60953 ай бұрын
Do you have any trouble codes have you had a tune on the car.
@nunyabinnis40693 ай бұрын
@joeybalogny6095 no check engine lights, will it throw codes without the check engine light on? Also i bought it modified and I assume it is tuned given the mods
@Theguv-nor4 ай бұрын
Crank relearn or not??
@joeybalogny60954 ай бұрын
Im not shure if this answers question it has the gear learn which allows ecu crankshaft position sensor or where crankshaft flywheel is replaced
@aleqsandre95634 ай бұрын
Hello, I have code P144c on my Ford Mustang. I changed purge valve twice but it still says the same error. What could it be?
@joeybalogny60954 ай бұрын
valve stuck open maybe keep going work threw it 1 thing at a time thats hard it can be tough.
@michaelmoralez66764 ай бұрын
This video sucked
@sam96325 ай бұрын
Hi great video, does this tool have a clutch pedal position relearn?, and if so can you show us.
@joeybalogny60955 ай бұрын
I don't think it has that option but I will try to find it.
@rtel1235 ай бұрын
That is why they invented electronic wire tracers! :))
@rtel1235 ай бұрын
@@joeybalogny6095 that was sarcasm :)
@joeybalogny60955 ай бұрын
Lol I got it you know then.
@legalize4205 ай бұрын
Can 20 amps handle a space heater and a microwave at the same time? 😂 Just curious how many amps that would need to cover.
@joeybalogny60955 ай бұрын
Most microwaves pull around 10 amps that is why a dedicated Circuit is needed a space heater pulls 12.5 amps so a 20 amp circuit can handle only one of those.
@legalize4205 ай бұрын
@@joeybalogny6095 good to know. Thank you.
@thechosen80835 ай бұрын
How about putting 12G to 15A?
@joeybalogny60955 ай бұрын
You can use no#12 on a 15 amp single pole breaker wont hurt anything but most people want to use more so 20 amps makes more sense.
@JereB6985 ай бұрын
I do handyman work and got a call to a mobile home that had dark black spots on a wall. The owners had installed a 30 amp breaker replacing a 15 amp to stop it from flipping off. The wires got hot enough to discolor the wall.
@joeybalogny60955 ай бұрын
I had one that was similar it was a house built on to a old single wide mobile home you could see the burn marks by the outlet box they pulled all the old wood paneling off I ran all new wire and new sub panel they had 30 and mix of 20 amp breakers on old no#14 they had space heaters that is what did it.
@JereB6985 ай бұрын
I did that when removing a door that had an electrical box for the light switch. Even taped it like that for extra safety, lol.
@AndrewdeKroon5 ай бұрын
How can i rate the wire to work with 20A?
@misteraon5 ай бұрын
In general 20A circuit requires 12AWG wire. Sometimes larger gauge (ie 10 AWG) for longer runs to compensate for voltage drop. There are charts for this online. But 14AWG wire is insufficient for a 20A circuit. The purpose of a circuit breaker is to protect the wire.
@joeybalogny60955 ай бұрын
No#12 works with 20 amps if you have no#14 on a 15 amp breaker you will need to upgrade the wire to no#12 some homeowners cant afford to upgrade there wire they unplug some things and plug into another circuit then they have more balanced circuits so there not tripping breakers.
@What1zTyme5 ай бұрын
Modern day equivalent of putting a penny in the fuse box.. back when there were fused electrical systems and US mint made pennies from copper. Fire risk is the same, whatever the illegal methods 🔥
@joeybalogny60955 ай бұрын
The old penny trick copper it will allow any amount of electricity to flow no protection very true.
@legalize4205 ай бұрын
Fuse box? I've heard of circuit breaker boxes, but never heard of a fuse box. What in the world is a fuse box?
@legalize4205 ай бұрын
Last I checked we don't put fuses in our circuit breaker boxes here in the US. Maybe england?
@joeybalogny60955 ай бұрын
Older homes like knob and tube from the 1940s used old fuse boxes which have glass screw in fuses when the fusing element heats up melts it severs the circuit most small homes were 60 amp old timers say fuse box but they are rare to see most homes have 200 amp panels.
@legalize4205 ай бұрын
@@joeybalogny6095 ohhh okay thank you.
@carnold.knowledge5 ай бұрын
I would recommend adding timestamps to the description for a video of this length. It can be kind of painful otherwise…
@joeybalogny60955 ай бұрын
Thank for you're input fast forwarding is not that painful to me thank you I will do that timestamp in future.
@Ps5GamerGuy066 ай бұрын
Mustangs have a smart alternator. Not always 14.5
@joeybalogny60956 ай бұрын
You're right bms manages it if you were to run the car for 10 or so minutes the voltage is around 14.0 volts as long as it's within charging range under 12 volts usually service charging system now will display.
@adriantho.75716 ай бұрын
Needed this thank you brother
@joeybalogny60956 ай бұрын
Any time
@Thyshiiicjfjfkfksk5 ай бұрын
Yea you do with that safety recall bro
@Phantom-mk4kp6 ай бұрын
I think the battery test function that complained 'software not installed ' , is for the optional battery tester hardware that can be bought separately
@bigsexy87236 ай бұрын
Can you just ingnor it? Will it hurt the car?
@joeybalogny60956 ай бұрын
As long as the purge valve is not open it wont effect the engine. It just wont pass an emissions test.
@81441047 ай бұрын
Tool is good. Person who use this need have knowledge how to use that.
@jorgemendoza1992jm7 ай бұрын
Nice video. I have this code p1459, my car wont take gas. I just replaced the purge valve and the the purge solenoid. But i still have the same issue it wont take gas and it still has the code. Can it be the canister it self?
@joeybalogny60957 ай бұрын
Yeah it could be the canister I would have done the same keep working threw it you will get it go threw each step.
@jorgemendoza1992jm7 ай бұрын
@@joeybalogny6095 I am going to replace the canister. Thank you!
@jorgemendoza1992jm7 ай бұрын
Just replaced the canister and still doing the same thing. I wonder why is not taking gas.
@hermanrogers13254 ай бұрын
Sounds like somebody took control of your car and got it fixed so it won’t take on gas so you have to take it to the dealership
@jorgemendoza1992jm4 ай бұрын
@@hermanrogers1325 I got it fixed! it was a vacuum hose that got melted with the exhaust.