I like that you mentioned tip size and straining 👍🏻
@jerrymosier99953 ай бұрын
Is there a place to put oil in the control max 1700
@MB-ng2rj2 жыл бұрын
how many passes did you use? Do you have to apply a second coat?
@royaltydog2 жыл бұрын
I’m trying to use my Titan Controlmax 1700 for the first time. I’ve primed & done all the proper steps numerous times but it’s spraying out of the sides of the spray gun tip. I know it has to be something very simple that I’m doing wrong! Suggestions ?
@jnghandymanllc32732 жыл бұрын
Christi, here's my recommendation. Take the guard with spray tip off the handle. When you squeeze the trigger, you should get a steady stream of paint out. That tells you the machine is primed and ready for spraying. Ensure the tip seal/washer is in the guard. Screw the guard onto the gun, don't tighten all the way. Insert the spray tip ensuring the spray tip goes all the way in. Tighten the guard onto the gun. Directions say hand tighten, but sometimes you can't get a good enough grip to get it tight enough so use a pair of pliers to aid in tightening it. Don't need to over do it on the tightening. If this didn't fix your problem, inspect all the parts and surfaces to make sure they look serviceable. If still not working, flag a painter down that's working in your neighborhood and offer him $20 for a quick 10 minute class on the sprayer. If he can't put it into operation and have it spray properly, then it probably has a manufacturing defect somewhere. Plus you gave the painter lunch money for 10 minutes of his knowledge. Hope this helps.
@eduardoabad66923 жыл бұрын
I just got one for $80 at FB marketplace. It works great.
@nobreighner3 жыл бұрын
Thank you JNG! Does the control actually adjust pumping rate, or just max pressure cut off? And is the range real, in that is setting 1 about 20% of setting 5? I am looking to use it to pump liquid at a controlled rate. Use the Titan ED655 now, but it won't go slow enough. Thanks again!
@jnghandymanllc32733 жыл бұрын
Great question. Short answer, I don't know. I'm familiar with the ED655 and I would say that machine gives you greater control on what pressure the liquid will be moved through the line at then the Titan 1700. The Titan 1700 system is designed to operate at 1,000 PSI. I do NOT believe the number 5 on the system corresponds to 1,000 PSI and the number 1 is 1/5th of that (200 PSI). I believe the numbers represent a range from just below 1,000 to just above 1,000 PSI that allows you to adjust the spray pattern based on tip size, hose length, and viscosity of paint you're using to achieve the optimal spray pattern.
@creativejustin72403 жыл бұрын
Hello, Great video. Do you know or anyone else on here know what tips I would need for Water based paint? Stain and polycrylic and polyurethane?
@jnghandymanllc32733 жыл бұрын
It's best to understand what the TIP numbers mean, then you decide what will work best for your situation. I say this because you can spray a water based latex paint with a 517 or a 311, paint just comes out differently. First number on a tip is spray radius when held correct distance from wall. So a 517 will produce a 10" spray pattern. You overlap 50% during passes so you're covering 5" every pass. The next 2 numbers are orifice size, in this example it would be .017". Larger the number, larger the orifice size, the more paint will come out. The data sheets for products normally specify what size orifice works best for that product. Hope this helps.
@jeremysteffens49643 жыл бұрын
How does this model with the correct tip size paint cabinets? Is it capable of kitchen grade paint quality?
@aircoolscott3 жыл бұрын
Can this unit be rebuilt like many of the pro models? Thanks for the great video!
@jnghandymanllc32733 жыл бұрын
I don't believe so. The manual didn't mention anything about a rebuild kit, so I doubt it.
@badaspunkbtch3 жыл бұрын
The pump is replaceable on the 1500 and I believe this 1700 as well.
@Coder-zx4nb4 жыл бұрын
Thanks for the review, after my terrible exp with Graco I'm giving Titan a run with a 1700. Hopefully it'll make short work of my fence and porch painting duties!
@jnghandymanllc32734 жыл бұрын
Good luck and if you have any questions, be glad to help.
@iamdirtyredd4 жыл бұрын
Silly question. I know it say airless so that means I don't need a air compressor right? Also is it good for latex paint?
@scbane4 жыл бұрын
Bought one 3 months ago based on your review. Working flawlessy so far. Thank you.
@jakejohnson77144 жыл бұрын
so will the harbor freight sprayer whats the big deal man!
@jlai38614 жыл бұрын
I noticed you use a bag strianer to filter out debris, what mesh size is it? Does it help to eliminate the gun clog ? My biggest complain about thiss thing is that it lack a gun filter which I have to stop and unclog from time to time. The typical yellow color gun filter has mesh size of #100, which equal to 150 micron, the strainer bags I can find on amazon are 600 micron, to big of the hole I assume.
@garyheaton47915 жыл бұрын
Why didn't you just wait to paint it, once to tore out that awful stained up crapper, and floor? Would have been easier.
@doublehelix11855 жыл бұрын
What a great idea. Brushes are a bit pricey so this will help so much. Ty!!!
5 жыл бұрын
Thank you very much for your excellent video. It was a motivation for me. I bought the same equipment in Home Depot for 250 dollars. Now, it's my turn... Thanks again!
@jnghandymanllc32735 жыл бұрын
Julio, best of luck my friend and knock it out of the park.
@dustoff4995 жыл бұрын
Just purchased this sprayer in part from this posting of yours. I was concerned the setup was for small projects (doors and such) and not have the backbone to do a house. Looks like it does and I look forward to painting mine, a much much smaller dwelling. My only question, if you remember, is how much paint is used to prime and fill the hose. I wonder if a quart of paint for a small project is not enough?
@jnghandymanllc32735 жыл бұрын
Good question, I think you'll only use a quart of paint or less to paint a front door or other small project, but I found that I need the 1 gallon paint can to be half filled with paint to have peace of mind to prime and paint a small project like a door. The intake with filter end needs to remain submerged under paint but not right up against the bottom. I think trying to do this with a quart of paint would be risky; don't know what would happen if an air bubble gets in the line and if you'll get spits. I look at it this way, if you end up having to buy a 2nd quart, then you've spent the money for a gallon the way they price things. So buy the gallon, make sure it's sealed properly, in a few years when you use it again just stir and strain and you should be good. By the way, like the handle. Spent 26 years in the Army myself; you guys were/are life savers.
@tiberiumsunwars14875 жыл бұрын
Mine runs constantly even when your not spraying
@jnghandymanllc32735 жыл бұрын
Hey TSW, if your sprayer is working properly, it sounds like you have the knob in the downward position (prime position). When it is in that position, it will run continuously with fluid being sucked up the intake hose and expelled out the smaller return hose. If you rotate the knob clockwise 90 degrees so it is pointing towards the front of the sprayer, it should run until pressure is built up in the hose with spray gun attached then shut-off. If that is not occurring, then I would say it isn't holding pressure....then I'd call Titan support line. I've talked with them on 1 or 2 occasions and they are very helpful. Good luck!!
@tombryan15 жыл бұрын
In California, a Licensed Handyman is bound to making no more than $500.00 a week in gross wage income. That is in place so they don't cross over and steal work from C or B Licensed contractors who are held to strict rules and comprehensive insurance coverage. Plus before a C and especially B license is issued, years of documented experience and a 2 part test is required to pass, one based on the trade laws, and the other based on trade knowledge. I have seen "handymen" break those rules many times, perhaps a felony keeps them from getting licensed, lack of experience, laziness, irresponsibility, etc. Painting that place for $500.00 seems undoable, are the laws different in your state?
@bedir313ahmet22 жыл бұрын
@@FranciscoMartinez-zv2rw 😄😆😂😀🤣😃😊😇
@trollslandan5 жыл бұрын
Looks good. Does Floetrol dessolve into water or in a mix with dish washing detergent and water? Also is it problem waste if say, a decilitre or two is left over?
@dpazicni6 жыл бұрын
Can a gun extension be used with this unit? Seems like it would make things allot easier?
@jnghandymanllc32736 жыл бұрын
I have not used a gun extension with this unit; however, the Operating Manual that came with the sprayer lists 2 gun extensions available for purchase, a 12" (Part # 353-709) and 24" (Part # 353-710) tip extension.
@andruwadel11016 жыл бұрын
Thanks for sharing the video on your use of the Titan 1700 sprayer. it was great. I want to know if you have used the sprayer for interior use, and how if may have performed in spraying on ceilings. How were you able to use the volume of paint remaining in the 50' plus hose ? Lastly, have you used it for small area spraying, such as spraying trim areas? Thanks - Lee
@CouttsDesign6 жыл бұрын
Great video. Very informative. I noticed you over-sprayed onto your shutters and trim. Did you repaint your shutters and trim with the sprayer or a brush?
@jnghandymanllc32736 жыл бұрын
Not sure if you can tell from the video or are familiar with Florida stucco construction, but both the shutters and trim are also stucco. They just raise, lower, or smooth over the profile of the stucco to achieve a contrast. Because it is done like this, the easiest thing to do is go back with a 4" roller and paint the white areas. If finer work is needed, a brush is used. Thanks for the question.
@ermisnovay12706 жыл бұрын
how far away from the wall do u spray not to drip first time painting my home with this unit