but what about a message says status :failed self test ?

Quiten el estéreo pirata que tienen y les funcionará 😊

Ahoj, potřeboval bych nutně poradit s instalací diagnostiky, prosím napiš na sebe email. díky moc

estou com este problema agora, e não consigo resolver, não conecta em nenhum módulo, percebi que só conectar aparece está mensagem após o teste, vcds CAN: Não pronto/a/s.

A mí me está sucediendo ese mismo problema en un vocho, con ignición abierta si entra, pero en marcha el motor no entra, el problema que me está causando es mi alternador, en los pines del DLC, está metiendo más voltaje de lo normal en la señal de línea k y el cable se sobreprotege

How to enable an non-genuine copy of VCDS. Tested with HEX-V2 hardware clone adapter from 2017 and VCDS 2018 1. disconnect everything (Data cable, internet and antivirus) 2. Open the VCDS file containing the installer 3. Install the VCDS file you need, make sure the install path will be C:\Ross-Tech\VCDS[XXXX] [in case its an alternative version, it can add something after the VCDS, like "Pri" in case if its a dutch reseller that sold the program to you. 4. once the installation is finished, you'll be asked if you wish to open the program, choose NO. 5. Now, if you have installed it and ready to go, you should also have another folder that contains the following file; "VCDSloader", this is your unofficial application that you will use to open the program. So there are two seperate files, VCDS.exe and VCDSloader.exe, both in seperate files. 6. Drag the VCDSloader.exe file INTO your installation path, in this case that should be C:\Ross-Tech\VCDS. You'll see many files there, its how it's supposed to look like. 7. Now, for easier purposes, make a shortcut of VCDSloader.exe for easier access, whilst its inside C:\Ross-Tech\VCDS folder. That shortcut you can place wherever you can access it easiest from, most often the desktop. 8. [Plug in hardware into OBD and laptop, it is supposed to give a constant green light, if it flikkering or gives any other colour, search online what it means.] 9. Now you may start up the program trough the shortcut, NOT TROUGH THE VCDS.EXE PROGRAM inside the folder, but the VCDSLOADER shortcut, or just simply the original vcdsloader file INSIDE the installation folder. 10. When you start it up, you'll notice that all options are greyed out besides "options". Thats because the program does not know which hardware you connected with the false software. So, press "options", then press "Test" on the screen. You will most likely find out that your software will indicate either that it hasn't found any hardware or that it the Com-port has no reaction with the hardware 11. If no connection, that means your USB driver probably isn't set up right. Go to device management and look up Com-port and USB-drives. 12. You'll most likely see two instances ; 1. There is no com-port, but there is a ROSSTECH HEX-USB drive in the USB section. 2. There is a com-port, AND there is a ROSSTECH HEX-USB drive present. In the both situations, I advice to uninstall the "ROSSTECH" driver completely and unplug your hardware from your laptop. Then plug it back in and you'll notice that there is now an "Unknown USB" present with a yellow icon (in another situation, you might still see the same as before, if thats the case remove it again). 13. Now, in the folder which you received from the vendor, the one where the original VCDS was where you installed the application from, also contains a USB-driver set-up. You can either run it with a set-up (if it's included) or do it manually. If you want to do it manually, go back to device manager > Unknown USB > update driver > Manual install > Driver location. If the driver is correct, and you did it correctly, you should now see "ROSS-TECH HEX-USB with VCP" in the USB drives, along with a new available COM-PORT. 14. [Skip this step if your com-port is either 1,2,3 or 4. if its higher, READ THIS!] If your comport is 5 or higher, VCDS will not recognise it in the "options" menu. So, go to Device manager>comports>properties>2nd tab (i believe) advanced, here you can change the current com-port to another number. You have to place it either at 1-2-3-4. Anything above that will result in a defect software. 15. So, if you did everything correct, you can now open VCDSloader again [TURN ON IGNITION!!!], then go to "options" then go and first test USB. If everything is perfect, it should give you a short list of stuff like Comport : OK Interface : FOUND! CAN : OK etc. When you test your com-port, (make sure you pick the right number) you should also get a confirmation with "COMPORT : OK, INTERFACE : FOUND!". So, right now you should be able to fully use all functions of VCDS. If you get an issue of "Interface not found" or "comport not connected", you can : 1. make sure antivirus is off 2. Test the same program on another volkswagen 3. Test other USB ports (common) 4. Make sure you turned on the ignition when testing 5. Check if the hardware is properly connected and gives off LED lights when testing/idle If all fails, always search more info on google or contact your vendor. This is how i did it for me personally, but i couldn't get it to work on a Volkswagen crafter 2008, because you need an extension for the hardware. The engine of a Volkswagen Crafter is a mercedes engine. So, tough luck.

Alguien me ayuda me sale en el test can: not ready

did you not see that your CAN is not ready? That´s the problem

Meu cabo vag kkl nao reconhece a central do carro como resolver isso

que es lo que haces man, lo resolviste o no ?

The problem in a can system! Can: not ready!!!

I get interface not found

did you solved this problem. i have this problem also..

man did you solve problem. i have same problem. what to do.

plug in the cable into the laptop & car, start your ignition and then run VCDS. open options and look for KWP (under CPU) select the top box 1281. then run a "test" and click save. after that go back to the module that wouldn't open and it should read. you are basically slowing down the CPU so it can connect to the module because the module can't send/receive data quick enough.

how was this solved?

hola buenas as conseguido hacer funcionar el programa yo tengo el mismo problema a que se debe

bad firmware of atmega162.