Joe Flo

Пікірлер

@chadbrown681 11 күн бұрын

Just got a brand new Kayo 60 for my son. Dealer said it is cold natured and we needed to run it with the choke partially on at all times. Well, that can't be right but what am I going to do when it's a gift for the holiday and it's a week away. We've got it to run one time, barely... guess I'll take it back and see if they can get it running.

@joerowe2473 2 күн бұрын

Comment might be a little too late but yes with choke fully closed it will die and what I did for my sons is slight bump open, start it and let it warm up a little bit and let him ride. With it being slightly open it doesn't sound like a lean or rich idle and engine doesn't bog at all while riding. So far its a great starter bike and runs great. I am impressed with it and I have no complaints and he loves it.

@aros007z 16 күн бұрын

Awesomeness

@Meatheadthings-q8u 22 күн бұрын

Ik this is old but before putting on the sensor do you have to turn off car unplug battery?

@JoeFloCreates 22 күн бұрын

A lot of service manuals say to disconnect battery when working with electronic sensors, but I usually don't unless it's something that is hard wired. This harness is protected so I just made sure the car was off. I think you are talking about performing a reset of the codes on the ECU, and for that we use an OBDii scanner.

@Meatheadthings-q8u 21 күн бұрын

@@JoeFloCreatesalright and do you know where the angled sensor is on passenger side?

@ChristopherRitaProfessionalDJ 23 күн бұрын

I just bought my son one of these about a week ago. I have had issues in getting it to start as a cold start as well it’s running pretty rough. Have you had issues with your son’s carb?

@JoeFloCreates 23 күн бұрын

This one went to a new home, but it did give us some cold start trouble occasionally. It sometimes took a bit to get warmed up, then it was good to go.

@jojo-dn7qb 24 күн бұрын

excellent video. i installed the edge on my ls2 advant x, but the adhesive it came with didn’t do a very good job and slowly started to peal off. i bought 3m 30lbs double side and its not going anywhere….ever. removing it in the future if i have to won’t be too much of an issue either

@qvarfoto 24 күн бұрын

Oh brother, THANK you!! I just got my 645 in the mail and was completely gutted when I couldn't get it working. No one I've seen here on YT to date talking about this camera talks about that strange kink about "M 1000" in the display and the buttons not working until you out film in it... I guess I'm not out of the woods yet as I haven't put film in it, but this gave me hope. Cheers bud!

@JoeFloCreates 24 күн бұрын

Hope you got a good one! They really are great cameras!

@jonathanbock8435 25 күн бұрын

10mm hex socket right? Isn't the hex self-locking?

@jordan1234564 29 күн бұрын

Is there an idle screw or an air screw on the carb?

@JoeFloCreates 28 күн бұрын

Yes. This one has an idle adjustment screw.

@jordan1234564 28 күн бұрын

@JoeFloCreates ah okay..I think the dealer broke mine off..

@JoeFloCreates 28 күн бұрын

@ if I remember correctly, it was behind the choke lever.

@jordan1234564 28 күн бұрын

@@JoeFloCreates yeah. And that's what looks like it's broken off.

@jordan1234564 28 күн бұрын

@@JoeFloCreates so according to the dealer. He said they come snapped off like that. Was yours adjustable? Is the dear being dumb?

@Kawzper Ай бұрын

Great video. Just bought the 45mm JBL cardo speakers, do you think they will fit?

@JoeFloCreates 26 күн бұрын

Not sure. The dimples in the helmet were a little bigger than the speakers I installed, but I didn’t measure them.

@rickfrase5306 Ай бұрын

Thank you for showing me how to fix the problem!

@JoeFloCreates Ай бұрын

@@rickfrase5306 glad it helped!

@ESSA20 Ай бұрын

Hey, could you not use the clamp ?

@JoeFloCreates Ай бұрын

I didn’t try, but it probably could have worked. I prefer the stick on mount. I don’t plan on taking it off.

@ESSA20 Ай бұрын

@ I just used the clamp it worked 👌

@JoeFloCreates Ай бұрын

@ That’s awesome! I figured it would, but I didn’t want to give bad information since I didn’t try it myself.

@adrianr8447 Ай бұрын

Mine left a very thin layer at the end and it’s so hard to take off even with the heat gun. Idk what it is but it’s a bitch for sure

@JoeFloCreates Ай бұрын

@@adrianr8447 have you tried using goo gone or something similar?

@elvato7418 Ай бұрын

How do you open your trunk does it still let you ?

@JoeFloCreates Ай бұрын

@@elvato7418 yes. The top bolts have to be removed so the wing can tilt back before the trunk lid is lifted.

@JWSGZ Ай бұрын

Hi bro, our new tail lights fit your 2016 GMC Yukon XL. Are you interested in testing them out?

@JoeFloCreates Ай бұрын

@@JWSGZ do you have a website I can check them out on? That could be cool!

@JWSGZ Ай бұрын

@@JoeFloCreates SHINEHOME is our brand selling on Amazon. How can we reach out to you to communicate the details?🙌

@JWSGZ Ай бұрын

@@JoeFloCreates How can we reach out to you to communicate the details?🙌

@JoeFloCreates Ай бұрын

@ send me a message on instagram @joeflo562

@Leo555ZZZ Ай бұрын

Easier if you remove the airbox.

@JanChacn Ай бұрын

Bro thanks for the video, would you help me to really know if the agk k6 i intend to buy is 100% genuine? Any tricks or something to look at in order to discard something wrong? I really like the helmet but i want to make sure im getting the genuine one

@JoeFloCreates Ай бұрын

@@JanChacn there should be a hologram on the chin strap and on the box.

@JanChacn Ай бұрын

@JoeFloCreates can you send me s few close up pictures of the helmet with that hologram? You can paste the picture link here, will appreciate that. Thank you mate

@PatrickCassidy-wd9si Ай бұрын

It would be cool to go through the jacking up you did - of the car and the engine. Also, did you take off the bracket when changing the front one?

@thepotbellyninja Ай бұрын

Was there s clip option? Why not use that?

@JoeFloCreates Ай бұрын

@@thepotbellyninja it came with a clip, but I prefer this option. The clip moves.

@aaronduran-k6w Ай бұрын

How’d you take the top piece off tho?

@BuyingCoastalWithCraig 2 ай бұрын

This is awesome. So many complaints about mounting Cardos to the K6.

@JoeFloCreates 2 ай бұрын

@@BuyingCoastalWithCraig it’s not that bad.

@BuyingCoastalWithCraig Ай бұрын

@@JoeFloCreatesdo you feel like the mic boom is uncomfortable? I’m still getting used to how close the K6s is to my face compared to other helmets. I initially thought it was too small but found the same feedback across the board.

@JoeFloCreates Ай бұрын

@BuyingCoastalWithCraig I do not. I used the thinner mic that came with it. I think if I would have used the mic with the boom, it probably would be a little uncomfortable.

@Nina-nh5pp 2 ай бұрын

thank you 🎉

@TroyD-vo1bz 2 ай бұрын

How many miles at the time of check engine light?

@JoeFloCreates 2 ай бұрын

I think this was at around 140,000 miles. I’m currently at about 185,000 miles and still going strong.

@TroyD-vo1bz 2 ай бұрын

Good to know they are really robust engines I have a much older 05 as well as an 06 express 3500. My 05 has 56K and the O6 has 79K. Engines have been good. The O6 is a cargo van so it needs brakes and front end work. The O5 is actually a road trek camper van. If there's any suggestions you have for maintenance at around 60,000 let me know. I'l be taking a 2500 mile road trip in May with the O5. In some ways I think the older ones were even more robust with much simpler transmissions. Chevy went to a 6 speed if I'm not mistaken. Did the 13 have a 6 liter? Both of mine are the 6 liter.

@JoeFloCreates 2 ай бұрын

@ 6.0 flex fuel in my 13. I’d recommend a trans flush and check your water pump.

@TroyD-vo1bz 2 ай бұрын

Funny you mentioned those two things as those were the exact two things I did this past summer on the 06. I was planning to do a transmission fluid change on the O5. I thought that water pumps were good for over 100,000 though. The only reason I changed mine on the 06 was the thermostat went out, so decided to do the water pump and tensioner as well as idler pulley and hoses all at the same time as a preventative measure. Everything was actually working at that point though.

@JoeFloCreates 2 ай бұрын

@@TroyD-vo1bz I just read an old comment. My van was at 110,000 miles when this happened.

@fgunter5210 2 ай бұрын

I can’t get the return line off

@JoeFloCreates 2 ай бұрын

@@fgunter5210 oh man! Hopefully you were able to get it off. Being old will make it hard to take off sometimes.

@superjacob0328 2 ай бұрын

Such a good friend

@sativasteve1861 2 ай бұрын

Brother if that’s a 1984-1985 Honda shadow I’d just give up now. Hold onto her for parts but goodluck in the long run.

@sativasteve1861 2 ай бұрын

I state this because even with my 20 year garage kept 7k mile mint 84 vt700; there are almost 0 parts to source.

@matthewshultz24 2 ай бұрын

Which machine are you using and can I please ask what your settings are? Thanks! 😊

@JoeFloCreates 2 ай бұрын

OMTech Split Fiber Laser Marker Engraving Machine. Not sure of the settings now. I would have to try to figure out those settings again.

@matthewshultz24 2 ай бұрын

@ totally get it! So cool though. Thanks for the reply. That’s a sweet machine you’re rocking!

@newmagic30 2 ай бұрын

Thanks bro I just had the same problem it was a fuse your video helped me much appreciated I definitely like the video and I'm going to follow you

@gavincox8498 2 ай бұрын

Great Vid 👍Thanks for the time to show us🙂

@josephhollingshead1848 2 ай бұрын

Okay so it looks like you just got aggravated and broke the clips I cannot find the video with someone showing how to remove the clips without breaking them anybody can just break it off of there

@MrPapakuka 2 ай бұрын

🤠

@RelevantWing 2 ай бұрын

FYI the fuse blows if you use the replacement bulb number form the manual as they pull too much current. The bulbs should be 7443's. The manual al says 7444's if you add up the voltage they pull slightly more then the fuse is rated for, causing the fuse to melt occasionally

@JoeFloCreates 2 ай бұрын

@@RelevantWing This is good information. I assumed it was being slightly overloaded, but didn’t think to look at the bulbs.

@jamesmendoza7077 2 ай бұрын

Just watched your videos, and i was able to change the battery thanks to you, though I did lose the 1/2" I was using

@introbikes451 2 ай бұрын

Satisfaction ❤

@p99capalot79 3 ай бұрын

So I’m not exactly sure how to connect it because it ain’t enough room to get to it

@Bo_SH 3 ай бұрын

Just curious, how did you know you needed new struts? Did the car drive rough? Just got a used 2010 Prius and it’s not as smooth hitting bumps on the road and wondering if that’s just how it rides or need new struts for a smoother ride.

@JoeFloCreates 2 ай бұрын

This one was pretty obvious when driving. Loud noises and not very smooth on the road. Based on yours not being smooth, I would guess that it may be time to replace them.

@HouseCallAutoRepair 3 ай бұрын

Would have been awesome if the fuse was good....Question now, is WHY did it blow?

@chrisandrews9539 3 ай бұрын

Great video. Thanks for helping me fix the wife’s brake lights tonight.

@WeekendMechanics 3 ай бұрын

I have an E46 convertible and for the life of me I can't understand how to get the A pillars out. Seems all I have to do is to pull.

@drewschultz4183 3 ай бұрын

now that’s some father and daughter bonding love to see it 🤘 teach them young

@38possum 4 ай бұрын

Fix that choke it'll probably stay running.

@JoeFloCreates 4 ай бұрын

Thanks. I’ll look into that.

@JMLUSA1 4 ай бұрын

Thanks Brotha, That was indeed, helpful! 😁👍🤓

@CesarMartinez-hj8ci 4 ай бұрын

Legend big help appreciate !!

@pencesonthemove1221 4 ай бұрын

Have you ever switched out the grips? They almost seem like a plastic and we want to change them but I’m not sure if I can or how I do it. Nothing in the manual

@JoeFloCreates 4 ай бұрын

This video I made is probably the closest to it. Just make sure that when you get new grips, they are the right size. kzbin.info/www/bejne/mnuQe4CdjMyGrtU