The main advantage is that it provides anticaking properties as required in some cases.
@joseenriqueagustin95972 ай бұрын
Servirá para tramos mucho mas largo, digamos 60 metros a mas.
@matiasraya51793 ай бұрын
Y para bandas de PVC?
@hejatexgmbh47533 ай бұрын
Yes, you can use it for Light duty belts made of PVC and PU or rubber. Some dealers of Ammeraal-Beltech and Forbo-Siegling are using it.
@matiasraya51793 ай бұрын
@@hejatexgmbh4753 I working at Ammeraal Spain. thanks for the advice
@hejatexgmbh47533 ай бұрын
@@matiasraya5179 Your colleagues in Netherlands are using Multiface officially. We provide it with Ammega label as requested from them.
@derrickbeier5 ай бұрын
😡 "promo sm"
@freddyzinkiewicz6608 ай бұрын
Vous avez bouché un trou, c'est tout. Réparer, c'est redonner la puissance nominal de la bande (en grande partie). Pour une petite déchirure longitudinal de cette taille c'est suffisant. J'espère que vous ne faites pas la même chose pour une déchirure transversale un peu plus grande ?
@hejatexgmbh47537 ай бұрын
Si vous avez une déchirure longitudinale de plus de 10 cm de long et 1 cm de large, nous conseillons d’utiliser des agrafes ou du tissus ou un patch EP160 pour reconstituer la résistance structurale. En cas de fente latérale, il est aussi possible de procéder de la même façon, mais il faut réduire l’espace entre les agrafes à plaquettes ou multipointes. Si vous avez une bande de très grande résistance, dépassant 1000 N/mm, il faut mieux prendre du textile et recouvrir avec Multiface 1.5, en utilisant deux plaques en acier et des serre-joints pour maintenir une pression pendant le durcissement. Voyez la fiche d’instruction pour cela.
@captaingoody8 ай бұрын
I belt spliced for about ten years and i never received my belt splicers coat...
@hejatexgmbh47537 ай бұрын
Sometimes new technologies are emerging. Why not for splicing?
@captaingoody7 ай бұрын
@@hejatexgmbh4753 mate it's about blood sweat and tears
@ABDELAZIZFELLAK7778 ай бұрын
الله عونك اخي رشيد
@chrismartin97439 ай бұрын
Hey guys, i contacted ypu through your website but had no response. Could you respond to this message? Thanks
@azerty-mz8ew9 ай бұрын
Quand on fais une jonction à chaud on ponce pas les plis
@danielmukaz8776 Жыл бұрын
Comment faire les calculs
@cityhue517 Жыл бұрын
Where can buy it?
@KeithHowellCrusherGuy Жыл бұрын
Do you have a partner for your products in the US?
@hejatexgmbh4753 Жыл бұрын
We provide the goods directly from Germany with FedEx. Send us an email: [email protected]
@azeezkhan199 Жыл бұрын
Canvir bellt. Caring mashin Videos. An reats
@alessiomarini6010 Жыл бұрын
Salve, dove si può comprare questo vulcanizzante?
@davidvan Жыл бұрын
What happends to the right side sample? Better?
@hejatexgmbh4753 Жыл бұрын
Some customer report that Multiface alone is the best solution due to the higher rebounding elasticity. The best is to try both.
@boujemaarafik9645 Жыл бұрын
Si possible vous pouvez faire la démonstration en activant le son
@vydra3422 Жыл бұрын
Flexebility? What about that? Is it useble for stone crushing?
@hejatexgmbh4753 Жыл бұрын
Of course it works also with other materials like stone, metal etc. Look on our web site www.hejatex.com is you need more information.
@hoconfirmation36052 жыл бұрын
is it possible to dispatch to india?
@hejatexgmbh47532 жыл бұрын
Yes, contact me in Germany: +49-9421-96884-0 or [email protected]. EDgar Jakob Managing Director
@srinunsv14142 жыл бұрын
Hi sir. Im from india. Can you share the mail details to contact you.
@hameedullahkhan23192 жыл бұрын
I am in the position to purchase vulcanizing machine please give specifications
@hejatexgmbh47532 жыл бұрын
Dear Mr. Hameedullah Khan, You will find some information about our vulcanizing presses on our web site hejatex.com/en/vulcanizing-presses/ A short documentation can be download there. If you have an enquiry we need to know the belt width and the required splice length and the type of belt. Please send the information to our email: [email protected] or call us in Germany: +49-9421-96884-0.
@user-ey2cx1tb1m2 жыл бұрын
Первое видео где хоть как то приближено к реальности и быстроте, очень неплохо. Если будет возможность сделайте видео на реальном конвейре
@hejatexgmbh47532 жыл бұрын
Проблематично публиковать видео с 30-минутным ожиданием. Никто не захочет смотреть видео так долго. Надеюсь, вы все еще понимаете, что продукт позволяет быстрее ремонтировать и подключать.
@onesixfive2 жыл бұрын
Very interesting, I enjoy conveyor belt test data! Cheers from Chicago
@hejatexgmbh47532 жыл бұрын
You can see most of the value on the technical data sheet on our web site www.hejatex.com. But the most interesting thing is an application with a transmission belt running at over 33 m/s at an operating tension of about 25% of the rated strength of the belt. After 3 years, the belt has already completed over 200 million cycles. This shows that Multiface can probably achieve a higher dynamic strength than conventional hot vulcanizing materials. You can see a video about this application on our website or on kzbin.info/www/bejne/jn6YnKuYa5pjaZY. If you have further questions do not hesitate to contact us directly in Germany: +49-9421-96884-0
@Panchamoorthy842 жыл бұрын
👍👍👍
@hejatexgmbh47532 жыл бұрын
Multiface is a hybrid vulcanizing material for the splicing and repair of conveyor belts, which help to solve many problems: no risks for people, environment, tranport and storgae (even if you forgot it in the sun), reduction of the process and required investment as you need only 2-3 bar pressure and a lower temperature as usual. It can be even used for the splicing of steel cord belts with preformed cover plates, without some limit of strength. If you have some question don't hesitate to contact us in Germany: +49-9421-96884-0. Edgar Jakob Managing Director
@blacktwang1012 жыл бұрын
do u sell Battery scissor on amazon?
@marianofernandez45632 жыл бұрын
Excellent like all products Multiface!
@tadeuszratajczyk40702 жыл бұрын
OK SYSTEM
@DL2_DESIGN2 жыл бұрын
Salve parlare italiano
@Panchamoorthy842 жыл бұрын
👍👍👍
@hejatexgmbh47532 жыл бұрын
I hope you understand that with the new hybrid vulcanizing material you never need to wait for the evaporation of solvents and that you reduce the processiong time to less than half. This is valid not only on thin multiply belts, but also on monoply belts and on steel cord belts.
@houssamoubahi89682 жыл бұрын
Ils y'a un Presse de janction de tapis 1300mm /500mm fabrication en Algérie
@houssamoubahi89682 жыл бұрын
presse de janction de tapis 1300mm /500mm fabrication en Algérie
@aboanass7392 жыл бұрын
C'est bonne travail bravo
@hectorsaucedo19632 жыл бұрын
Gracias por compartir Dios les bendiga
@hectorsaucedo19632 жыл бұрын
Ola buen día donde se puede conseguir el multiface
@onesixfive2 жыл бұрын
You guys are warriors! What a nasty job. Results look very good!
@wedlma3 жыл бұрын
Wie sind ihre Erfahrungswerte mit diesem verbindugssystem?
@wedlma3 жыл бұрын
Welche Materialkosten hat man für eine Welger rp535 pro Riemen?
@saschadiehm59023 жыл бұрын
Würde auch gerne wissen ob und wie lange das hebt dauernd reißen die Verbinder
@hejatexgmbh47532 жыл бұрын
Teilweise sehr gut wenn die Verbindung richtig gemacht wurde. Es ist eine echte Alternative zu endlos gewickelte Riemen. Besonders interessant ist dabei der Preis (30-50% günstiger) und Einbau ohne Demontage des Antriebssystems.
@hejatexgmbh47532 жыл бұрын
Die Haltbarkeit kann genau so lang wir bei endlos gewickelten Riemen sein, wenn die Verbindung mit einigen Tricks gemacht wird. Und sollte es zu einer Beschädigung an den neuen Riemen kommen lassen sich solche Riemen eher mit Metallverbinder oder mit Multiface 1.5 reparieren, da diese Riemen Textillagen beinhalten. Rufen Die mich an wenn Sie mehr wissen wollen : 09421-96884-0
@SonkeHansen-tf5wn5 ай бұрын
Moin ich habe gerade dein Video gesehen ganz interessant kann ich sie morgen mal anrufen und wann ich habe ein paar Fragen Gruß Sönke
@andreybelomestnov20253 жыл бұрын
Тип ленты? Разрывное усилие?
@hejatexgmbh47532 жыл бұрын
Сопротивление разрушению соединений Multiface выше, чем у традиционных холодноформованных или горячеформованных материалов, как это было в России (вы можете связаться с Антоном: +79183357692). Но самое интересное - это применение ремня трансмиссии, работающего со скоростью более 33 м/с при рабочем натяжении около 25% от номинальной прочности ремня. Через 3 года ремень совершил уже более 200 миллионов циклов. Это показывает, что Multiface может достичь более высокой динамической прочности, чем обычные материалы горячей вулканизации. Вы можете посмотреть видео об этом применении на нашем сайте или на сайте kzbin.info/www/bejne/jn6YnKuYa5pjaZY. Если у вас возникнут дополнительные вопросы, не стесняйтесь обращаться к нам напрямую в Германии: +49-9421-96884-0
@hejatexgmbh47532 жыл бұрын
Позвоните нам напрямую: +49-9421-96884-0. Viktor Foos Говорит по-русски.
@akpenegagnonadjessode87343 жыл бұрын
très bonne vidéo !!! S'il vous plait, pouvez-vous nous fournir la référence de la presse que vous avez utiliser ?
@hejatexgmbh47533 жыл бұрын
Bonjour Monsieur Akpene Gaggnon Adjessode, Cette presse est une veille presse de la marque Rema Tip Top, sous le non WK. Elle fonctionne purement mécaniquement et obtient 2 bar de pression et 120°C. Cela fonctionne très bien avec le produit hybride WK, mais aussi avec notre nouveau matériau de vulcanisation Multiface. Si vous voulez des explications complémentaires, ou une offre de prix pour une presse vraiement moderne, n'hésitez pas à me contacter sous: [email protected] Salutations Edgar Jakob, Managing Director Hejatex Phone: +49-9421 - 96 88 4-0
@drewjohnson46733 жыл бұрын
US mkt is huge. A little English on your site would skyrocket your product. A local distributor would do even better.
@hejatexgmbh47533 жыл бұрын
Dear Drew Johnson, Yes you are right the US market is very huge and Multi-PE/PP is unique and surely very interesting for many customers. On our web site www.hejatex.com you will find a documentation in English. If you need something do not hesitate to contact us by email: [email protected].
Bjr mr. J'aimerai acheter une presse occasion svp. Oû peurai-je la trouver.??
@hejatexgmbh47533 жыл бұрын
Bonjour Rachid Kaaam, Nous ne proposons que des nouvelles presses, destinées à une une utilisation très intensive pour durée de vie maximale. En conséquence, nous n’avons pas de Presse d‘occasion. Je peux cependant vous proposer une nouvelle presse si vous me contacter personnellement. Mon numéro de téléphone: +49-9421-96884-0 ou e-mail: [email protected]
@hejatexgmbh47533 жыл бұрын
Donnez-moi moi vos coordonnées téléphoniques. Je connais un client qui désire vendre sa presse d’occasion.
@azezkhan4023 жыл бұрын
pon namar
@lucianolizana4463 жыл бұрын
what can i use to glue polypropylene and acrylic?
@hejatexgmbh47533 жыл бұрын
Multi-PE/PP was developed for the bonding of all types Polyethylenes and Polypropylenes as you can see on technical data sheet on our web site www.hejatex.com. It works also on EPDM rubber, Viton and PU with best results. In some cases we had also good results on teflon. If you have some questions call us: +49-9421-96 88 4-0.
@jatinmittal51673 жыл бұрын
Do you have a supplier in India?
@hejatexgmbh47533 жыл бұрын
Currently we don't have a partner for tools in India. If you wish, we can provide it directly from Germany. Plase call us: +49-94 21-96 88 4-0 or send uns an email: [email protected]
@niknik13993 жыл бұрын
Сколько цена?и доставка по всей России?
@hejatexgmbh47533 жыл бұрын
Свяжитесь с нашим партнером в России. Он сообщит вам цену и условия.
@rohanchikhalkar9943 жыл бұрын
IN WHICH COUNTRY YOUR COMPANY IS IT.
@hejatexgmbh47533 жыл бұрын
We are a German company near Munich. Look on our web site www.hejatex.com
@rohanchikhalkar9943 жыл бұрын
@@hejatexgmbh4753 sir can i get your whats number
@rohanchikhalkar9943 жыл бұрын
can you share your number i have to discuss some business talks