Are all gaskets universal because I need one for my 2014 Toyota Corolla but every Autozone that I go to and ask for one doesn't know shit😭😭😭
@dreamyjoker8182 жыл бұрын
Its your power Steering. The compressor is going bad so it needs a rebuild if you was swinging it. Then you need a rebuild with better quality seals try to buy those pieces yourself only the Seals and check if any of it is Dented or broken. It could also mean you need a new alternator. Check for Leaks on the Subframe or floor cause it will get worse. I had that issue but thankful I fixed it cause every turn i took the noise will keep getting louder.
@36ELGALAN2 жыл бұрын
Your exhaust system looks brand new. Weird that the gasket would of failed so quickly
@red666A2 жыл бұрын
How about the rear coil over? Is the same way as adjusting the the front coil over?
@elleelle79962 жыл бұрын
Doug - THANK YOU for this video. Will you marry me??? You just saved me a small fortune!! This is EXACTLY what I needed replaced - while Lexus dealership wanted to ring me up to replace entire catalytic converters ecosystem - or it would not pass inspection. You’ve saved me a fortune and easy walk through knowledge training. Much appreciated!
@Jonj572 жыл бұрын
Fuck yeah, can finally even out my exhaust tip
@jad54873 жыл бұрын
Thank you for this video.. I got a code P0420 (bank 1) and while I was changing my oil I noticed that one bolt was missing from that sealing area so I’m suspecting there’s a leak from there that’s causing the problem. This helps solving it, thank you!
@reneflores88323 жыл бұрын
It’s that easy! I’m new to cars and my z exhaust gasket broke :/ but now I’m confident I can fix it thank you!
@masonb67473 жыл бұрын
Very good explanation thank you
@paolav18913 жыл бұрын
Thank u bro
@351kostakis3 жыл бұрын
Fantastic
@trr52913 жыл бұрын
I've had them on my car for regular use since 2019. They work just fine. They are a little rougher is my only complaint. They get through snow fine too. Michelin quality? Hell no but they get the job done. After 2 years I didnt lose much thread.
@sukiiish3 жыл бұрын
Thanks very good idea.
@melvinlara-falcone23624 жыл бұрын
Like your video one thing you should be installing well using a bolt spring assembly kit resonator exhaust moves when Engine speeds up and goes from drive to reverse if you use regular Bolt & Nut the vibration will loosen them up and you'll have the same problem again. thanks for sharing your video.
@kenicam.production69104 жыл бұрын
Clever!!!
@elig9794 жыл бұрын
Can you just use any hex bolt ? With lock washer ?
@Nitterundercove5 жыл бұрын
Nice video, I’m wondering about my 240sx on the right back tire and panels are so close to each other I can’t tell if it’s my panels are my coils that making my panels and tire touching each other :( don’t like it because I just got a new tires.
@redcarter37935 жыл бұрын
Thank you short and simple
@TwoInfinityAndBeyond5 жыл бұрын
You should've cleaned it first before putting in the gasket.
@rodriguezandres545 жыл бұрын
Is it the same for the back
@blaineknowlton135 жыл бұрын
Man that's ur ps pump put flued/bleed it
@justme33505 жыл бұрын
Soo what diameter clamp do i need???
@Anthony_in_Bloomington_Indiana5 жыл бұрын
Is this car brand new? I need some method to cut off the 2 nuts on the end of the exhaust manifold in my 2004 Toyota Corolla. The damn nuts are WELDED to the flange! And, of course, they are super rusty. I appreciate the effort you put into making the video, but really, it doesn't help anyone. Everybody else in the known universe has rusty bolts and nuts on their exhaust pipes, and those are stubborn critters.
@tomregina73015 жыл бұрын
Don't even bother with them. I just used a reciprocating saw with a metal cutting blade to cut off the rusty bolts without damaging the flange. You could also use an angle grinder.
@brandongarcia26885 жыл бұрын
What size bolt did u use?
@themechanic42226 жыл бұрын
Anytime u work on that type of connections u shout add some RTV because they start leaking after awhile
@FriedEggsandJellyfish5 жыл бұрын
Nope. Just get a quality gasket you won't have to use rtv. Rtv is when you don't have a gasket..plus makes it a pita to clean.
@truepyro286 жыл бұрын
Bought these 3 weeks ago. Getting then mounted in the morning, and hope they do half decent in the rain
@reallyokaydad6 жыл бұрын
so is it true that you were raised in Santa Cruz, moved to so cal. Then recently moved to the east coast? Because that's my life haha.
@DougDrifts6 жыл бұрын
Sir Tiller Yoooo, sorry for the late reply. Raised in watsonville, moved to socal then the East coast, so pretty close haha.
@reallyokaydad6 жыл бұрын
Doug Drifts that's awesome man. I'm dying to move back to California. I saw on your wife's channel that you guys are moving back. There really is no other place like it.
@YelloPhase6 жыл бұрын
Hey! Wondering what brand your gasket is? and where you bought it? I need the exact one you have for the aftermarket exhaust I just picked up. Thanks!
@DougDrifts6 жыл бұрын
GT86 Hey! So I don’t recall the last gasket I put on, but I at one point used a gasket from Vibrant (1458) and then also went directly to Greddy for the part, which I don’t recall. But if you have the exhaust they can help. Think it was like 9 bucks or something.
@esti55066 жыл бұрын
Dude just get a poly exhaust bushing. Will be mad strong, and done right.
@esti55062 жыл бұрын
@@MrRusell86 instead of rubber, its made from polyurethane...
@bryandeharo50967 жыл бұрын
Hey I got a question did you hear that noise when you would drive it ? And if yes did you ever fix the problem? Because I have the same problem with my 240
@DougDrifts7 жыл бұрын
Does your oil light come on at all? Or whats your oil pan look like? I had a huge dent in mine and it was actually straining the oil pump. Knocked it out and that ended up fixing it! But like others have said here, you might wanna pull belts and eliminate those first, because the oil pickup tube makes taking the pan off a huge pain. Hope this helps, let me know how it goes!
@bryandeharo50967 жыл бұрын
Doug Drifts it’s pretty hard to explain but my oil pan does have a pretty good dent in it and it seems like it’s not losing any oil
@bryandeharo50967 жыл бұрын
And the oil light doesn’t pop up either , did you end up changing the oil pan?
@bryandeharo50967 жыл бұрын
If you did , where did you get it at? Thank you !
@DougDrifts7 жыл бұрын
Bryan De Haro so my oil pan had a dent and the light would flicker occasionally, I didn't get a new one just banged out the dent on it using a 2x4 lol
@melissanguyen57617 жыл бұрын
Awe sad you covered hello kitty, don’t know what she did to deserve that haha
@DougDrifts7 жыл бұрын
Melissa Nguyen Hello Kitty kept falling out while I was drifting so I had to tape her in place lol
@s42627 жыл бұрын
Nice quick video very simple very helpful thanks
@DougDrifts7 жыл бұрын
Johanna Espaillat no prob!
@chrismullan21257 жыл бұрын
Some slick drifting. Just seen the channel today and like the vids. Looks like a sweet car, don't think I could keep up with the maintenance seems like some hard work! 😂
@redsaint20227 жыл бұрын
Can it be any similar looking gasket? Autozone couldn't find the original match but I bought one similar
@DougDrifts7 жыл бұрын
francisco rojo Just make sure it's the right diameter and the bolt holes line up! If you have the same exhaust Greddy sells direct replacement, or you could go with a brand like Vibrant
@redsaint20227 жыл бұрын
Doug Drifts , awesome!! I will do that! Thank you.
@vstaritz7 жыл бұрын
That's funny, it's almost like after the second time you spin out you just switch into drifting perfectly fine mode
@DougDrifts7 жыл бұрын
ChocoboXii00 Sometimes it just works, but thanks! Haha.
@r18a1USDM7 жыл бұрын
do you have to put gasket sealant?
@DougDrifts7 жыл бұрын
r18a1USDM i did not! And I don't believe you do, but because this gasket kept breaking and my exhaust scrapes all the time I didn't really care haha
@themechanic42226 жыл бұрын
Yes
@abymondesir237 жыл бұрын
great clear explanation and footage!
@handymaneh7 жыл бұрын
What would happen if I max out being low??
@pnojazz7 жыл бұрын
To raise the car, how is turning to the right "counter-clockwise?" Wouldn't turning to the left be counter-clockwise?
@DougDrifts7 жыл бұрын
Haha, I guess if you're moving your hand its to the left, but I guess I was thinking spinning to the right if it's like a clock.
@Rainingpenuts7 жыл бұрын
if the spring is held tightly by the top 2 locks, can you just turn the entire spring with your hands instead using the coilovers wrenches or is that bad?
@DougDrifts7 жыл бұрын
I wouldn't say it's bad, but make sure you're rotating the whole thing and not just the spring! The threaded part is what moves in and out of the sleeve, raising the car up and down.
@timothykakue3317 жыл бұрын
how was road noise, handling, vibration on any speeds im thinking about buying a set.
@joshuacampodonico65547 жыл бұрын
timothy ka kue I bought these for my 2000 Infiniti i30 the Road noise is quite grip and rolling resistance is good the treadwear is better then my Firestone FR740 performance tire which are Garbage but they're not Toyo or Michelin either but worth the price to expectation and I do enjoy the ride with these also that's for California weather I'll update this for my Toyota Corolla S Plus I just bought driving now in Oregon.
@jojobaja8 жыл бұрын
Nice driving Doug!
@DougDrifts7 жыл бұрын
Thanks, Joan!
@HelValkyrie8 жыл бұрын
Awesome job! i would love to drift one day!
@DougDrifts7 жыл бұрын
Thanks!
@jordanchilafoux18008 жыл бұрын
Go Doug!
@DougDrifts8 жыл бұрын
Jordan Moats Thanks!
@addison47278 жыл бұрын
How did you get interested in drifting?
@DougDrifts8 жыл бұрын
Addie A combination of having a father thats into cars, growing up around racing, friends that like cars and Need for Speed the game haha
@addison47278 жыл бұрын
+Doug Drifts Thats so sweet!!
@unvcht50468 жыл бұрын
my name is Rashmul
@abymondesir238 жыл бұрын
Very impressive car do you have a rear camber kit?
@DougDrifts8 жыл бұрын
HYPE WARRIOR!! Thanks! And I do not, stock arms in the rear