@@fisher7840 bytte ifrån Albin 25 till stora systern Albin 30 för ett tag sedan (ungefär samma båt, likvärdig planlösning, sjögång och framdrivning, bara lite större och något "modernare utseende på ovan däck"

Att en båt bara skulle suga åt sig vatten på ena sidan har jag aldrig hört talas om, att en båt lutar lite åt ganska normalt, Min båt ligger "plant" med full dieseltank, full vattentank och tom septiktank, Efterhand som septiktank fylls börjar båten luta höger o lika så efterhand som dieseltanken töms så lutar den höger o efterhand som vattentanken töms börjar den luta vänster, stora frågan är iaf varför endast den ena tanken används? Alger i den andra? (Isf kommer det troligtvis snart i den andra också) Trasig tank? (Anledningen kan vara många) Om det kan vara av intresse så har jag en corallsnipa 22 i bra skick till salu till väldigt bra höst/vinterpris

Länk till annonsen, så kan vi ta det därifrån isf facebook.com/marketplace/item/896592829059764/

Lite lutning är normalt om inte tankarna är i balans, men ska inte luta något märkbart, då är något fel

@@sv.alannah Dometic wont make this any more, but the guy o know sells basically the same but under the name oriondo 3000

@@sv.alannah here you can find it, let them know you found it on this youtube when you order www.oriondo.se

@@jongray5411 no cavitation, (if you get cav its to high) i will do one more "transom fix" on the dinghy we have now soon, but that one will be in fibreglas

Dont make it to high, the cav plate on the outbord should be in line with the bottom of the boat or slightly over for max speed, little lower then bottom for max gripp and power

@@tophe9281 ja i Albin 30 är det de orginal fast det är väldigt trångt och orginal så leds duschvattnet ner i kölen o sen får länspumpen pumpa ut det

@@onthesurf Ah, tänkte inte på att ni bytte båt. Jag har själv ingen ännu, men suktar lite efter en Albin 25, Nimbus 26 eller liknande size. Lär mig väldigt mycket från dina videos och det är himla kul att se hur mycket bra idéer du har.

@@tophe9281 Nimbus 26, saga 27 etc etc ja de är lika stora utvändigt men innuti är de väldigt små och planlösningen är sådär. Gå ner i en saga eller Nimbus o sen ner i en A25 så tror du att du är i en betydligt större båt Om du vill ha ännu mer videos men framförallt enklare åtkomst, chattfunktion etcetc så kolla in min Patreon (kostar dock en liten slant) men är svårt med kommunikation på youtube, laddar upp mer videos där o framförallt så kommer de upp där först, innan de kommer upp på youtube

Har du någon länk eller dyligt så jag kan kolla specifikationer?

A guy i know does make both the stoves and the canisters but under the name oriondo instead of origo (Dometic will never start making these again) let them know you found out here when you order www.oriondo.se

@@Ramenscooter let me know what you think about the canisters when it have arrived

@@onthesurfhello, thank you for the video. I am from America, I looked on your friends website. Hard to navigate. How would I go about messaging them on selling one, and if they would ship to US. Thanks Justin Ps- if i can’t get them. What is the material you used to stuff the canister

@@JHdude87 i have asked him about your question and waiting answer, the material is rockwool (Fire proof insolation, it can handle 1000 Celcius)

@@JHdude87 you can email him direct on this adress, tell him you found out here when you send him a email [email protected]

Many thanks, tell your friends to subscribe and help the channel grow

Heavy duty 4423 kzbin.info/www/bejne/mnbFYoRqjcqgsMUsi=IYcIyJy8GSRQlePK

1 knot = 1,15mph 1mph = 0,869 knot My normal cruising speed is about 6-7 knot 7*1,15=8,05mph Topspeed about 12kn = 13,8mph

@@onthesurf peki 2000devirde kaç knot

@@esatakyuz3604 about 8-9

@@onthesurf peki Albin kaç HP?

@@onthesurf 24-30 HP

You mean the burner for the oven?

@@onthesurf the one the alcohol goes into. Mine has a hole that sits on the air or flame setting ajustment

@@redwood1957 you put alcohol in direct in the burner (the one im refurbishe) you just pore it on the rockwool/the net (have it standing upp when you fill it, because you have it on the side and fill untill it flows over its going to be about half when its laying flat = full) I just upploaded 4 short videos on the burners to my Patreon (link in the video description) thats what i could uppload fast and easy (no editing needed) maby i can do a full "how to" video when i have launched the boat

I will try and help you with this but i cant send pictures here, if you want you can join my Patreon, then we can use the chat and send pictures/vids and talk direct. I will try and make a full how to vid on the hole origo 6000 in the future, but it will take som time

That's fine I have an older orego.

Dometic will never start making them again, but a guy i know does but they are now under the name oriondo instead of origo, let them know you found out here when you order www.oriondo.se

@@onthesurf Many thanks!

@@prof.heinous191 let me know what you think about it when it have arrived

No its going in my Albin 30, (the big sister to A25, its basic the same only bigger)

Wery good, its the gelcoat that gets boring, but a new layer with gelcoat or polyuretan paint and it is as good or better than new

I will do what i can to get them in production as fast as possible

Tack så mycket, ja det med lagerfett är ett knep jag alltid använt o det är även med i någon av de äldre videorna, Jag hittade detta settet på Hornbach i Kristianstad (glöm inte o prova med en magnet, fastnar den på borsten så är trådarna järn med ett ytskikt av mässing = skadad/förstörd propp. ENDAST ren/solid mässing får användas. Ja här finns video på mycket o mer kommer efterhand, vill man ha ännu mer o även mer hjälp, direct chat o massa annat så kan du kolla in min Patreon (länk finns i video beskrivningen)

so then do it bro stop watching the video lmao

Absolutely right Paulo. The plates became completely useless after adding those ridiculously over-built steel risers and massive, cast eyebolts. Way too much weight at the worst possible place. The motor is now too high and will cavitate excessively as soon as he tries to turn. Also, sealant needs to cure before bolts get fully tightened or it will just squeeze out. Since he also neglected to through-bolt the engine to the transom, as stipulated in the owner's manual, I expect this o/b is going to end up at the bottom of the fjord.

@@UguysRnuts it still works great, no cav, since its a long rigg on a short transom you need to raise it to get it to "normal" height. Sailboats normaly have a long rigg or eaven a xl rigg and share the motor with the dinghy, then you have to do this. If you have a long rigg on a short transom dinghy it probably wont eaven get up on plane. And if you make a gruve around the hole you can tighten it fully direct, then you will only squeeze out the "extra" and it will be a good seal around the bolt like a o-ring if you make a gruve. The big bolts with rings surves too purposes, 1 something to ty down the motor with since this on dont have any way to bolt it, 2: good mounts to drag/pull with (pulled the A25 of a sand bar using this)

@@onthesurf If you're going to double down, so will I. Water will easily saturate your transom since you, not only didn't seal the the grain in those massive bolt holes, but applied no sealant underneath the stainless steel plates which are sandwiched up against the original, textured transom plates creating a wide open channel to trap and funnel seawater directly to the holes in the transom. Are you seriously going to leave 6cm of excess eye bolt protruding on both the inside and outside of your transom? You've got to be joking??? And don't try to tell us it doesn't cavitate excessively on a tight turns. I know it does. I've been working in and on boats since before you were born and have seen it all before.

@@UguysRnuts there are sealant around al the holes and since the hole are bigger than the bolt it is sealant al the way in. You cant put it between the plates and the transom, no point because when you tighten it it will just squeeze away anyway, as long you put it on the bolts it will fill the hole upp total and then squeeze out and make a good seal around the hole in the transom, so water cant get in the transom, thats the only important, if water gets in between the transom and the plates it still wont get in the holes in the transom, but since there are no sealant between the plates and the transom it can drain away

Happy to help 😎

Ingen extra app, bara att ansluta via Bluetooth o starta Spotify

Javisst o mer kommer :)

Tyvärr, tog mig 4år att hitta en. Dock så kommer den nog förhoppningsvis att börja tillverkas igen. Jag har kontakt med tänkt tillverkare

Så om du känner fler som kan vara intresserade av dessa (både 1, 2 lågigt o 2lågigt+ugn) säg till dom att prenumerera o sedan skriva en kommentar, något i stil med "vill ha" När tillräckligt många är intresserade så börjar tillverkningen

Får kolla när barnen somnat

3266f278 Men alla som ser ut så i toppen ska fungera lika dant enligt den infon jag hittat (köpte 2 olika packningssatser o med dessa 2 så ska man kunna packa om vilken cav pump som

Yes, one thing at a time and before you know it, its done

Soap for wood cleaning, there are green, white etc. I use the green one

Its based on linseed oil

linseed soap, here in Sweden its green, in your country it can be a different color

I took AL kabels out and started from scratch, if i remeber correct 70kg of gost stuff just laying around

I never had a Isuzu engine, so i dont know

On the surf Facebook is best for contact facebook.com/profile.php?id=100067804628777

Gick till närmsta plåtverkstad o bockade en rostfri plåt i 2-3mm. Sen en vattentålig "träkloss" som är lika tjock som akterspegel o så hög som man behöver höja (ta med klossen o säg att den ska vikas runt denna, se till så du gör den ordentligt längre så det går att bulta fast det ordentligt

we have bought a ~10m motor yacht. Look for the next episode 😎

@@onthesurf a 30 footer? alot more room for the family.

Yes and ~1m wider 😎

Japp, det blev en ca10m lång motor yacht 😎. Håll utkik efter nästa episod

If i remeber corect its 174

@@onthesurf wow, that’s a early number Mine is hull #1727

You dont see the slime and other crap that sticks to the boat, just wait until you put it in the Hard to clean it

Many thanks😎

is ther any Facebook group that is aboat boat in general, in your country? if so can you post Link ore the name of THE group

@@onthesurf Trailer Trawlers is one and i think a second is Boats under 33'.

Faster, easy to get up on plane, and almost no nose pitch ( nose pitch = the Bow stands up in the air and you need to move to get the nose down and up on plane)

Can make a vid when i drive it next

is ther any Facebook group that is aboat boat in general, in your country? if so can you post Link ore the name of THE group