Hi, you can. You might need to adapt timings to the different product.

Yep, same reported by other users

there's an opv fixed version around the web

Hello, I don't use the single basket as is very difficult to get a decent espresso shot. Unfortunately I don't have advices for this 😕

@@romitagl Grazie Gian Luigi. La mia macchina è nuova e I uso qualche volta singolo, ma è vero che il più difficile. Oggi ad esempio, sono riuscito a farlo con 8gr di caffè. Secondo me, il problema è nella forma di filtro.

I think so. It’s looks pretty much the same

Start checking if the pipes are not damaged and there’s no leakage. I’d surprised if with the original steam wand you had more pressure but you can put it back just to be sure that there’s no other issue

@@romitagl - I Opened the top during use to check for leaks there’s nothing. Although, using the one hole Tip instead of three holes seemed to help a bit

No, I don’t

In linea di massima direi che non è necessario macinare finissimo per la moka quindi metà di quello proposto potrebbe bastare. Purtroppo bisogna fare qualche prova per trovare il settings corretto. Considera che dipende anche dal caffè utilizzato (io devo aggiustare in continuazione a seconda di quello che trovo).

@@romitagl Grazie mille per la precisazione!

Audrius. L yeah, sure. Can be tried to see if you improve the brewing results 👍

Arda Ertas hello, the milk jug is 300ml, correct and I generally put 200ml of milk

Arda Ertas Looking at the 35.31 looks exactly the same to me so I’d say yes, it should be the same. Regards

Hello, please check out my video: kzbin.info/www/bejne/o2SQe3eaq9OJiJo

The pressure is a lot lower on mine and sometimes nothing comes out, what should I do ?

sana raheem I personally upgraded my grinder to a stepless one so I can’t confirm on the lifetime, but I guess that it depends on how much you use it, independently from the modification.

@@romitagl thankyou for quick reply.. How many months did u use it after this change. And did it work fine till u upgraded to better one

sana raheem I used the grinder for several months without problems

AC Toon hello, I don’t have the grinder anymore to experiment with it but you could try to do the opposite modification (turn the burrs in the opposite direction)

Hey, hows the hack holding up? the worm drive looks like it would be great for espresso, I also found 40mm burrs on ali express and fitted them to a Gaggia mm grinder with very similar internals to this (without the worm screw ajustment though). looks very interesting!

you too huh? ecp3420 , too bad delonghi warranty is nonexistant, returns only for unused and no exchanges. This will come in handy as I rebuild things, was your problem the top O ring ?

@@lichdust No my problem was the frother valve which is connected to the frother knob. It was leaking. You replace the entire valve and it took me longert get the metal clamp off and on the tube than to do anything else. You will see the metal clamp is very strange and has a little place for part of it to reengage. You may want to invest in radiator hose type small clamp to replace it. I was about to go to the home center to get one when I finally got to reclamp correctly. Other than that it was easy. Also, to get the metal front off, you just gently pry it with flat screw drive and then the back upper part comes off using two flat head screw drives to press in on the two plastic locking mechanism. Trick is to press them at the same time and push a slight bit upward to disengage each. You do not have to disconnect any wires unless you have to replace something that is wired. Hope that is helpful

@@lvsfineartssurvey thanks for that, I think my valve is still good, the pointy steam outlet on the steamer (47) is where the o-ring failed for me, and a second one so I came back to see if it had the exact size and so far a replacement has already failed after one go, so trying another one out. Those hose clamps can be tricky especially if you can't get a good pinch angle, just from working on my car :D extra tight zip ties for me.

Just gave this a go with my Dedica too. Yeah I barely got anything out on the finest setting. Dialled it back 2 notches and it was coming out nicely - but damn it's so much stronger now there's a finer grind. Absolutely knocked me socks off.

@@v4o82 can you tell how many clicks until u get the 90 degrees ?

Ciao scusami ma ho fstto un disastro devi aver girato troppe volte la rotella e non fa rumore ma non macina più tu sapresti come rimetterle a posto? È nuovo sono disperata 😭😭😭

Hello.. How long did your grinding work after this change. Does it decrease the machine life?

sana raheem still working fine

@@dompercy so three months gone?

sana raheem yeah

36g of liquid is not the same as 36ml of liquid

@@ghosttrader-x1n gottem

Generally 5 seconds is enough.

Stefano Alderighi ciao, se parli di quelli di teflon direi di sì. Considera che non possiedo più il macina caffè da più di un anno quindi non posso fare nessuna verifica aggiuntiva :-/