Omg the little hand 😂😂

would have been nice to see the time lapse part of you using the stock ecu connector wires for the k engine harness and conv. harness at normal speed

I don't ever want to do it again either. I had read about the through-the-firewall method and tried it. I couldn't get it out and had to do it the other way. Finding all the fasteners was the hardest part. The dash components went in easier than they came out.

Ahhhh been there, buddy... I just did this a month ago since my AC decided to go out mid summer. 😅😂

Great video, I just installed my wheel yesterday but when I woke up this morning my car wouldn’t start. Have any ideas?

For folks watching this you do not need to do all this. You can pull it from the firewall. When you disconnect the lines from the firewall you take out to Allen head screws grab it with needle nose pliers and pull it out. Then you just reverse.

What were the symptoms that made you aware it was the expansion valve?

Question about the shroud .. The bolt that came with mine or short n i cant get them to screw on did u use longer ones?

When we going to see more vids. It's been a minute. Lol que paso mija. I hope all is well.

Nobody told me that a shoe horn connector was necessary to make the horn useful until i watched this video explaining. Thank you 🫡

It helped me out thank youu

What pannel gauge are u using? It is digital?

Super easy, thanks for the video.

Thank you! 🙏🏻 After tons of videos finally you explained perfect.

Does anyone know what that “litte metal ring” is called and where I can get it. At 7:51 she talks about it. I’m missing that and need it to finish mine 😅

The baby hand has me dead lmao

Ah pero tú hablas español que bien, espero un saludo de tu parte también estoy en un proyecto igual desde Venezuela, saludos

Hi

The little hand took me out 😂

Took me 2 days to find this video thank you for showing what an actual clean install looks like without cutting wires 💚

after 6 years of having a NRG quick release setup, with a momo wheel, I finally wired up my horn. THANK YOU AC Labs🫡 edit: 92 CX hatch with SRS so the relay part helped me so much.

I did mine in 20 minutes.. I’d rather work on Hondas than on land rovers and jaguars any day

You did one thing wrong, you forgot to put the temp sensor wire in position. You left it hanging low and pinched it. There is a notch in the evaporator cover that its supposed to sit in.

How does mold get into a vacuum seal system? No no no Never clean the inside of evap or condenser with any other type of cleaner only ac refer line cleaner Clean the outside fins only

I did this job several days ago on a 2007 Civic. Just know that all the screws, bolts, and nuts are accessible, even though it looks intimidating. Slide the seat all the way back, sit where you can see up inside, and you'll find them. For another video detailing this job, with good visuals on the fastener locations, see: kzbin.info/www/bejne/f6TdhodmmNyph68

Great video. This guy had to cut some area out of the firewall but was an acceptable solution. Save you from pullng all the inside AC system apart. Always use a little oil to help o rings slide into their bore. kzbin.info/www/bejne/mGW7mHiKqKqKhpI

Random question. What flashlight is that?

Glad to watch determination, thanks for sharing!

Where do you get those gauges

Thanks for the vid! just did mine and this helped me a lot. I was super confused at one point because I could not for the life of me find one of the blower motor bolts. Turns out the little speaker for the door/headlight/seatbelt chimes came lose and was hanging/stuck to the bolt i needed. Lots of other weird little issues this helped me through too. Thanks again!

i have to do that in my 2010 honda civic 🥵🥵🥵🥵......

❤❤❤❤

❤❤❤❤

Amazing step by step tutorial I really appreciate it so much and clear quality video

I want to marry this woman 😍

If you replace the compressor, is it obligate that you replace the expansion valve as well?

Which color is from b plug??

That’s what’s up thanks

Cool exhaust, i'd love this on my ep3

Someone who knows how to wire a Honda on KZbin thank god, guys you need to step your game up she’s out here killing it

sick!

The expansion valve can be changed from the underhood access hole. For pete's sake!

Hi great video! I am needing to replace my expansion valve as well but I can’t seem to find the form insulation anywhere, where did you purchase yours from?

I wish you had not used the background music. It distracts.

Thank you I’ve been looking for this detailed video no one else has one 🤘🏻

looks great Im doing the same build so I'm amped to see you vids your audio was a bit low but the vid was good

Fantastic job. I bought a momo steering wheel and hub. I too have been looking thru yt on removal and installation concerning the srs airbag and horn wiring. Very few give detailed instructions on the later. Thank you for including the part number for that shoe horn. 🤙

Doesn’t sound like 3in would be to loud to daily. I had a fab shop turn me down and my 3in material/piping bc he didn’t wanna make my car lose power by going 3” header back, with resonator and muffler

Ugh, I wish I didn't have to cut that one piece. Everyone seems to be cutting it to get the blower out.

It’s always awesome to know that there are females car lovers. Love the shirt as well.