Hi dude I’m buying this car later any chance we could have a chat about it
@bills41352 ай бұрын
My corsa opc has the same MAP sensor (Bosch 0 261 230 048) from the factory. I know it because I bought the car new from the dealer. I works well and it is a 0.2 to 2.5 bar and -40 to +130 C . Its specs are: Voltage output is 0.4 to 4.65 V linear to the input pressure 0.2 to 2.5 bar and NTC thermistor of 2.5 Kohm at +20 C. Your new Bosch 0 281 006 076 is a MAP sensor of 0.2 to 3.0 bar and -40 to +130 C. They are different. Their Vout related to the temperature is the same, but the 2nd one outputs 4.65V when P=3.0 bar (not 2.5 bar). The pressure does not get that high, but the problem is that at a given pressure (let's say 1 bar atm + 1.2 bar boost = 2.2 bar absolute pressure), the 2nd sensor (the new one) will output a smaller voltage than the original 1st sensor would output, the ECU will think that the pressure is lower (because of the smaller voltage), and the end result will be the ECU controlling the wastegate in such a way that the actual pressure will be higher than 2.2 bar. Hopefully, the engine will not run a leaner fuel mixture in boost conditions, because the ECU calculates the fuel based on the MAF sensor readings (in open loop mode, no O2 sensor readings at high accelerating) which will be correct. So there will be a mismatch in air pressure and air flow, with unknown results. Theoretically, your ECU will read 1.843 bar (around 0.843 boost) when actual P=2.2bar (1.2 bar boost), and it will produce (if exhaust flow is capable) around 2.635 bar=> around 1.635 bar overboost instead of 1.2bar overboost. Also, it will produce (if exhaust flow is capable) around 2.391 bar => around 1.391 bar normal boost instead of 1.0 bar normal boost. Finally, Bosch 0 261 230 302 and Bosch 0 261 230 283 are drop-in replacements for Bosch 0 261 230 048 . Also, the bad sensor output was low (around 0 V , out of the valid range 0.4 to .65V) and the fault disappeared by replaing it, beacause the bad sensor got out of the system.
@Richard250002 ай бұрын
Whats the bores oval and taper. Whats your wall clearance Whats your trust clearance Whats your mains and rod bearing clearances. What about valve shimming.. So much not done or checked.. all these details are ignored, which makes the difference in power and reliability and life span.
@carlclark57083 ай бұрын
Hi mate any links for parts used thanks
3 ай бұрын
Hi mate, great vid keep it up. Could you get in contact with me. I just neeed some invoices for yhe vxr mate, the forge paperwork if you can. Thanks
@flippingcarsrepairs3 ай бұрын
Another great video i had my fingers crossed for your 1st drive to the mot station,great it passed .sad to see the 350z go sounded amazing.good luck with the move u lucky bugger 😂😂😂
@Dipper884 ай бұрын
Great work on both cars. Both successes!
@adambutler484 ай бұрын
Thanks man! Bit of an odd video to put together running both cars in one video but needed to be done this time! Thanks again for watching too! 🏎️🏎️🏎️
@fossilfish7864 ай бұрын
Sad to see the 350z go but I'm sure it's for the greater 👍
@adambutler484 ай бұрын
I felt the exact same! I really didn’t want to let this one go but I can’t keep them all! Anyway onwards and upwards! How are you doing also?
@flippingcars1014 ай бұрын
Great video bro 😎 and well done on the rebuild and getting it through a mot. Keep up the amazing content bro 😎
@adambutler484 ай бұрын
Thanks man! It’s coming together! How’s things going your end? I need to spend some time watching yours man! 🏎️🏎️🏎️
@flippingcars1014 ай бұрын
I haven’t been uploading anything to be honest but il be starting again soon Iv been busy with other things and getting some parts together and just need to find some time to start working on the cars again.
@flippingcars1014 ай бұрын
Head unit is sick.
@adambutler484 ай бұрын
I know what that’s like man! Seriously life and everything in between gets in the way! I hope all is working well for you and the family though and your all keeping safe! We still need to do something together one of these days! Would be awesome fun to! 👍🏼🙌🏻
@flippingcars1014 ай бұрын
I’d really like that bro 😎 it would be amazing, I hope you move next to me bro 😢 I guess not if you getting on a plane ✈️
@adambutler484 ай бұрын
It's been a while since we've seen the 350Z here on the channel! Now that we have a buyer lined up, I need to get these last few tasks complete. Let me know what you think of the new Tesla Style Head Unit in the comments down below, Would you do this to your 350Z?
@markmawson14 ай бұрын
I looked like it's the first rebuild you have done becauewhen you were torquing the head bolts they didn't look like 90° turns, don't be surprised you end up with head gasket issues
@adambutler484 ай бұрын
Hey, thanks for watching! Yes it was the first build. I’m sure we mentioned that? And we did use the correct tightening procedure with torque and then degree tightening, apologies I didn’t do a great job of explaining or showing that in the video. Really appreciate the feedback though 👌🏻🏎️🏎️
@user-iw5zg4nj9e4 ай бұрын
Great video, but the final test is whether it lasts under boost and for any length of time!
@adambutler484 ай бұрын
Very true words… I guess only time will tell! Thanks for watching! 🏎️🏎️
@user-iw5zg4nj9e4 ай бұрын
@@adambutler48 It looks like you did a decent job and were mindful of the main things which can screw things up. Fingers crossed.
@paulsanderson19544 ай бұрын
Great video, Adam. Look forward to catching up with you next month. 😊
@adambutler484 ай бұрын
Hey man! Yes for sure!!! I can’t wait to see you both! Thank you so much for your help on this one!! Will have some fun this summer. Let’s plan a road trip together!
@shujabeg76254 ай бұрын
Why would you not get the upgraded stem seals that have a built on washer to keep them seated
@adambutler484 ай бұрын
The stem seals that we used were the ones that came in the rebuild kit straight from Nevlock Performance. If I had bought everything individually then I probably would have done so! Thanks for watching man! 🏎️
@shujabeg76254 ай бұрын
@adambutler48 I checked nevlock a while back and they sell them s standard on there full rebuild kit. What pistons did you use?
@adambutler484 ай бұрын
@@shujabeg7625 we used the Wossner 79.5mm pistons with Nevlocks own branded Conrods 👍🏼
@shujabeg76254 ай бұрын
@@adambutler48 👍
@adambutler484 ай бұрын
Its been a long time coming guys but I've finally got my latest video out for you all. Let me know down below what you'd like to see next on the channel! Can anyone guess where I am at the end of the video yet?🏎
@Dipper884 ай бұрын
Fair play to you man. Ambitious little project but all came good. (I'd say you were fairlu relevied !)
@adambutler484 ай бұрын
Thanks man, relieved is certainly how I felt when I heard it crank! I’d love to do another one again!
@Jackoplayz544 ай бұрын
:)
@adambutler484 ай бұрын
Hey Jack!
@darronbutler33254 ай бұрын
Well done Ad what a excellent job to build an engine for the fist time mega scary stuff done to perfection. Well done fella.
@adambutler484 ай бұрын
Thanks Darron! Been a while coming but pleased to get this one out now! Wait for the updates! Lots to cover and lots of adventures this year! Can’t wait for you to come out here too!
@flippingcarsrepairs4 ай бұрын
Well done you made that look easy i had my fingers crossed when u got it started👍
@adambutler484 ай бұрын
Thanks man! I had my fingers crossed too!!! 🤣🤣
@NowsNu4 ай бұрын
Awesome job lads! I'm still curious what the issue was exactly with the very first startup, always eager to learn -) cheers !
@flippingcarsrepairs4 ай бұрын
Maybe a earth 🤔
@adambutler484 ай бұрын
Bang on! Turns out it was a bad earth on the started! But the issue was from under the fuse box not the usual spot 🤯🤯
@fossilfish7864 ай бұрын
Good efforts bud.
@adambutler484 ай бұрын
Thanks man! Well pleased it’s not still in thousands of pieces!
@flippingcarsrepairs4 ай бұрын
Were have you been hiding 😂😂😂
@adambutler484 ай бұрын
Feels like I’ve been living under a rock for the last 8 months man!
@flippingcars1014 ай бұрын
Lol you need to stop leaving me bro 😢, Iv been checking up to see if you have uploaded but you hadn’t. Good to have you back bro.
@adambutler484 ай бұрын
Hey brother how are you?? Thanks for this! I keep meaning to get things out but life has just got in the way all this time. What’s new in your world?
@flippingcars1014 ай бұрын
Nothing new but since you back il start uploading again, my new channel is @weflipanycar
@flippingcars1014 ай бұрын
Well done on getting the car sorted bro 😎.
@adambutler484 ай бұрын
Yeahh do it man, Let me check out the new channel...
@MichaelMitchell-jq9bz4 ай бұрын
Looking good big man
@adambutler484 ай бұрын
How are you big guy? Miss you
@MichaelMitchell-jq9bz4 ай бұрын
All good here missing you to bro
@flippingcars1017 ай бұрын
What happened to the videos bro
@itskidkelly7 ай бұрын
You beautiful British wanker you just saved my ass 😅 you have no idea how long I have been fighting the upper oil pan. Until I watched your video I didn’t realize there were bolts inside that I had to undo. Thanks from your relatives across the pond.
@rickybutler66898 ай бұрын
This car is now up for sale by another owner I’m looking to buy it was there a reason for why you sold it ?
@callumhenstock87348 ай бұрын
Hi Adam great video just saw the exact same car for sale and was wondering if you could get in contact with me about proof of engine thank you
@flippingcarsrepairs9 ай бұрын
Great video how much did you get that for needs alot of work but will be fun 👍👍👍
@massagemytoes41929 ай бұрын
They aren’t deep scratches. It’s where the clear coat cracked because it’s too cold outside
@raphjl92829 ай бұрын
Wow great job, currently looking to do the same thing with the headliner. I'm not too sure about the paint on the visors. I was looking to get black visor, but can only find leather one for the convertible modele (in use and good price). Do you know / think the convertible one will fit the coupe 350z?? Can't really find an answer online for that.Otherwise imma have to paint them like yours! Thanks!!
@williamstanley109510 ай бұрын
"Promo SM" 😋
@flippingcars10110 ай бұрын
How are you brother, not seeing any uploads lately 😢hope your doing well ❤
@byronshaw391210 ай бұрын
I have a black z with the light coffee or "orange" seats. The seats pop and it looks awesome from outside the car. Looking forward to what you will be doing next for the console as I'd like to do it too! There's a sub from SA! Great vid
@adambutler4810 ай бұрын
Thanks for watching! Your right the orange seats do make it unique as most owners do prefer the black seats too. Thank you for the sub also!
@rahxe8010 ай бұрын
Wow great job!
@adambutler4810 ай бұрын
Thanks so much, I aim to be dropping some more 350z content shortly! Thank you so much for watching!
@1MADZ10 ай бұрын
You are about to put a tablet in that spot on the waterfall.
@adambutler4810 ай бұрын
You could well be right bro!
@1MADZ10 ай бұрын
That's tedious 😅 great Patience.
@thiagocanola55411 ай бұрын
Shouldn't you polish it before applying the clear coat? That is how I restore my headlights and it looks crystal clear.
@adambutler4810 ай бұрын
Thanks for watching, it’s great that you’ve found a way that works well for you! I’ll have to give your way a try next time and see how it comes out too. 🤞🏼🤞🏼
@Walduck2511 ай бұрын
Where are you from? in the UK of course
@adambutler4811 ай бұрын
I’m based in Staffordshire. Thanks for watching too 👍🏼👍🏼
@darronbutler332511 ай бұрын
Adam another good choice gona be diffrent beast this one. A fully built engine and turbo wow this is a lot of work. Can't wait to see your journey with this one.
@adambutler4811 ай бұрын
Hey Darron! The turbo scares me but some things only get done when we push ourselves to do them hey! You’ll like the end to this one! A fitting end to this journey for once!
@cfcdave342511 ай бұрын
As a corsa d vxr owner I must say your brave taking this engine on for your first rebuild although I’ve heard they’re easy to work on once you get to know them, defo gonna follow the channel now and learn from you 👌
@adambutler4811 ай бұрын
Thanks buddy! Really appreciate the watch and sub! I think having taken endless images and having all of the footage from recording does make it a little easier! I firmly believe that we can all do it no matter our skill level! The right few tools and a can do attitude will always prevail!! 💪🏼💪🏼💪🏼
@flippingcarsrepairs9 ай бұрын
@@adambutler48totaly agree 👍👍👍
@dominicdelf26611 ай бұрын
Ive replaced an engine Adam but this is something else .....great camera work great content well done mate i watched all the way through, impressed
@adambutler4811 ай бұрын
Thanks Dom, wish I had tidied up the garden beforehand but hey sometimes there’s just too much to do. I hope your doing good also!
@Dipper8811 ай бұрын
Couldnt understand why it wasnt just a replace whole engine job untill you said about remaking it to be a built engine. That makes sense. Still this level of dissaseembly makes me stressed!
@adambutler4811 ай бұрын
It stressed me out for a few days before I even attempted to tackle it too 🤣🤣 if there’s one thing I can tell you after doing it, it’s way easier to look at it now and understand what’s going on having done it than it ever was before. I’ve put off doing a job like this for so many years out of fear of messing it up but overall I’d tackle it again in a heart beat. It was a ball of fun looking back on it! Thanks again for watching too!! 👌🏻👌🏻
@dominicdelf26611 ай бұрын
Respect Adam!
@adambutler4811 ай бұрын
DOM!! We need to do coffee!! I’ll give you a call in the morning! ☕️☕️
@flippingcars10111 ай бұрын
Bro 🤩 well done 👏 I wasn’t expecting you to get started on the engine. Really really proud of you doing all that with no experience, Iv got a car you can help me with, we can do a Collab and il pay you as well if you interested. When you all done of course ❤ keep up the amazing content.
@adambutler4811 ай бұрын
Thanks big brother! I’d love to do a collab with you! No need to pay me at all I’m happy to do get stuck in and help out! Let’s chat for sure! I have some pretty big news coming in the next few weeks so we will need to get something out together for both of our followings! That little Fiat of yours has got my taste buds tingling again already!! I am slightly jealous haha ❤️🙏🙏
@flippingcars10111 ай бұрын
@@adambutler48 lol 😂 don’t worry bro it’s sold now, and bought sometime a bit differently, im looking forward to hearing your big news, lol what is it tell us now if not when will you be releasing that information out.
@NowsNu11 ай бұрын
Awesome content Brother, great to see already much work on it in its introduction, love that ! Love these cars as well, they get a bit of a bad rap, yet gotta love the performance in these little under the radar things. Your upgrade of the engine sounds fantastic, sounds so much fun and it certainly is to watch, cheers mate !
@adambutler4811 ай бұрын
Hey buddy thanks so much, I’m really appreciative of your feedback and I’m pleased you enjoyed it! I always wanted one of these back when I was 17/18 years old, it was just the insurance that made it impossible back then. You’re right they do get a bad rap don’t they? It’s a shame because they’re a cool little car! Let’s hope the rebuild goes nice and smooth too! 🤞🏼🤞🏼🤞🏼
@fossilfish78611 ай бұрын
Brave man😮
@adambutler4811 ай бұрын
Either that or stupid but I’ll take brave! Haha thanks for your comment 💪🏼💪🏼
@fossilfish78611 ай бұрын
@@adambutler48 nah your work is to a high standard, like what you've done so far. Well done. Love the longish video can't wait for the next.
@adambutler4811 ай бұрын
Thanks again, it’s great to get the feedback too, it’s a real battle to work out whether to do longer format or more shorter format videos but I guess a mix of the two will probably be best!
@paulsanderson195411 ай бұрын
Great video 👍
@adambutler4811 ай бұрын
Thanks Paul! Wait till we see your lovely mug on the next one haha
@adambutler4811 ай бұрын
Thank you so much everyone for all of your support! The channel is doing really well and for my 10th video I wanted to treat you all to a new car… Enjoy
@midnightmoves7976 Жыл бұрын
Had the same problem with my rear stays, had to drop the tank and the rear subframe to well the chasis where teh bolted in.
@adambutler48 Жыл бұрын
Wow! Yours rusted out pretty far then! I guess these are just some of the costs of owning some of these older jap cars hey!