Garbage

What I don't like about Handyman work is I usually have to go back to the hardware store to get something I need and don't have. I remember installing a ceiling fan and it had the two chains for the fan and light. The ceiling in this particular room was higher than normal so the chains had to be extended. So, I had to go back to Home Depo the next day to get chain extensions to finish the job.

Gracias míster, I'm in México watching your vídeo in 2025 I got about a year trying to figure out how to replace my 1999 chevy silverado running bulbs , your vídeo is very helpful, thanks ,gracias amigo , I'm gonna try to do it tomorrow, they were 20 dollars in the USA 🇺🇸 but here in México are very expensive, probably like 100 dollars both , gracias amigo.

Mine will not clear codes. Bs

If your addition was on the other side of that wall, and as you said the addition is wired with modern grounded romex, could you run a ground from this outlet over to the closest switch or outlet on the addition side?

I needed this, thank you

So I pulled out 3 glass fuses from my panel and didn't realize they were rated differently, how can I tell which sockets are 15a and which are 20a?

Bless you !!!!!❤

Do you have to turn the power off?

Subscribed because you steed the number one reason people have troubles right away. So common and it’s on the can!!😂

I very much appreciate your comment on warming the can. My attempt, it came out in globs and did not spray. I was about to just chuck the can as I'm yelling POS about the product. The video wasn't very clear, couldn't see anything on the wall, but the commentary was what I needed

Thanks I needed this mines is 2 wire..

I replaced busted fuse but still doesn’t work. No idea what’s the problem :(

Thanks! 🎉

T15

Thanks! You don’t need 30 minutes for every DIY project. Concise and to the point. Excellent introductions. ❤

Also I did buy the hose that is specifically made for buddy heaters that says no filter needed yet I still had the problem with oily substance accumulating inside the heater lines n my heater no longer works

According to what I've learned it is the chemical that gives propane gas an order that will accumulate inside the hose or inside the heater lines that will cause the heater to not work properly or at all over time.

Thank you! Especially the part about removing the black plugs. God bless you

Brother I'm framing in -25c that's not cold

Appreciate it, sir

Great job thank you for taking the time to post a great video 👍

Thank you so much. very helpful!

Thank you! I had installed these under my kitchen sink some years ago and I wasn’t sure about the collet so I search here. Appreciate you taking the time to show us how to connect and disconnect. Subscribed!

I have the black max chain saw with the 18' bar and chain i love the saw but the chain brake spring is to stiff im going to have to trim the spring to get to run right

Thank you!

why is it only the red necks make the best how to video on the topic of shit and toilets?

what brand was it?

Does it have Bluetooth

Would've like to see finished bathtub chair-set in the tub,,, would've been nice to see!

Just a tip, I ran myn for 30 min changed the oil the. 1 hour changed the oil then 3 hours changed the oil. A little overkill but oil is cheap and you will see how much crap is in there

After installing Z flashing I install 1x4 backing strip between studs if they are 2 ft on center. This provides a place to screw the siding down above and below the joint to prevent future buckling between studs which is generally why people want that unsightly cap board on top.

I narrate what I’m doing whilst working on my parents house … but I’m not even filming only one listening my dog and the fly that Keeps trying to land on my face

I’m doing a similar repair on my shed. Can someone please provide me with a link or specific description of the Z flashing that’s shown in the video. Thank You!

This is exactly what I did except that I used 5/8" T1-11 siding. It didn't match the existing siding thickness. It caused a few problems particularly for the new trim.

The WIND did it, not the weight of the plywood. The plastic looks VERY sun weathered.

Did anyone understand wtf this guy even said?…

So basically, if you need to cut off electricity in order to do something like replacing a bad light switch, you will have to take out a particular fuse and put it back after you are done with your job?

When you're drilling into the brick and when you are trying to drive the anchor, your drill is making the same sound. This leads me to believe that you either didn't have hammer mode on for both, or you did have hammer mode on for both. You should turn hammer mode off when fastening. If you find the full installation instructions on Tapcon's page, they say not to use hammer mode when fastening.

Great instructions! Thanks

how about doing it in the dark , your vid quality sucked but your instructions were sound

Whoa !!!! Thanks bud, will work on mine and let you know. 👍🏻👍🏻 from: Redondo Beach, Los Angeles, California

HOW MUCH OIL?

I can't see nothing SMH wtf

Thanks for the video, I did mine without removing the seat. Also re-used the zip-ties with the pointed ends that go through the frame holes for retention.

That must be a shed, it’s 3” off the ground. No wonder it’s rotted, I’m surprised the floor joists aren’t rotted too. Should all be pressure treated.

2005 gmc sierra, i look at the spots tonight. Horizontal and vertical. Checks out!

Nowhere on the cans does it say warm it up. I tried and tried and it just came out blobby or total liquid. I'll never use it, a waste of $15.

How can you do a review if you haven't tested it?

Very helpful since it didn't come with instructions. Thank you