What can be done about screw for turn off water breaking

You tell people to put the seats and springs back in the same order that they were removed but you do not mention which way the tapered spring inserts. Since a previous install might have been done incorrectly you should have been specific about which way the taper goes.

What else ca be used to lubricate

Helped a lot on Christmas. Thank you for posting this

These tutorials should have been watched way more! You are awesome!

if the pilot lights, and stays lit, does that mean the TCO is ok?

Searched for the video for the furnace… somehow it’s the same thermostat too. 😅 How is that possible.

How to remove the water above the check valve for service? My sump pump check valve is low on one pit and high on another any reason for this?

Thank u for your best teaching.

This video is golden for new home owners 🙏

When I let go of the pilot button the flame goes out😢 I held it for 30 secs then tried 1 min and tried a few times again and it won’t stay lit once I let go

Great video. Definitely subbed! 😊

I have a 30 year old heater that has had zero maintenance. How do I know when it's time to replace?

i have removed the defroster element and plugged it directly to the wall, it is heating up and does not trip the circuit breaker. But when i plug it back to the fridge its trip the circuit breaker. What might be the issue?

Love it

On mine the flap that closes for crushed opens for cubed it stuck open. The selenoid clutch moves freely just seems like the arm is backwards. Any thoughts?

Dear Sir, kindly to download the video for my presentation.. Thanks in advance

Superb instruction. Each furnace is a little different. The explanation on what each line did and where it lead was very helpful.

Sir after completing refilling the water heater tank , should i'll leave open the valve for cold water supply? Or shut the water supply inlet valve off once filling is complete?

Why it is not dangerous to backflush? Because the open faucet will outlet the pressure?

awesome. thanks

So I hear the furnace on but I don’t hear the blower motor blowing air. It just continues to turn on the flames but not blow it out

THIS -Ladies and Gentlemen, is how a tutuorial should be done.

This is the best video out thank you

Very good 👍

Mine makes noise

Great and very detailed video! The only item missing is to mention that when replacing flush valve, instead of regular get full port one - it will speed up flushing and remove more debris.

Hello, My Kenmore oven heater stopped heating on baking mode, but works on broil mode, please if you could tell me what could possible be the reason? Thank you 🙏

thanks

Very good video

My flush button sticks what do I need to do

Why don't we have pretty versions of these in our homes?

Thank you!!!! Cleaning the flame sensor did the trick.

Why are these VERY simple operations always given by Americans ? i wouldn't employ this guy to sweep up.......

Thank you for your excellent videos. I want to share a few things that I -- a petite total amateur -- learned replacing two diaphragm modules. 1) Removing the diaphragm cap may require more torque than channel locks or a small wrench can provide, especially if there is some corrosion involved. I had to buy a heavy-duty 15 inch wrench. 2) It turns out I have one low-flow flushometer and one regular. I have no idea how to spot this from the writing on the unit. Once I accessed the diaphragm of my master suite unit, I saw it had a green top. Since I had purchased a standard 3.5 GPM kit, I installed it, but it leaked terribly at the vacuum breaker and ended up destroying the vacuum breaker. Incidentally, if you are also replacing the vacuum breaker and are using a green diaphragm, you need a breaker that is 651, not 551. With the green diaphragm and the proper breaker, my master suite toilet now works perfectly. The older toilet in my guest suite used the standard diaphragm and vacuum breaker. Incidentally, I also replaced the handles while I was at it. They work much better now -- they clearly were on their last legs. (And yes, both of my upstairs toilets broke within hours of each other on a Saturday. I'm a new owner, and there is some deferred maintenance here. I learned a lot fixing these and will be ready for next time. Thank you for saving my weekend!)

Well explained; doable 🙏🏼

Great video! LG refrigerator, loud grinding noise, like motor being jammed. Stops when doors opened

Great info, very helpful. Thank You.

What if I have 9 ohms? All other safety’s have continuity but no heat

In the diagram, around 38 seconds, isn't there a direct short when line voltage in the defrost control ties directly to the neutral. Got it! That has to be the motor circuit.

Thank you for your expertise, and your video! The visuals are AWESOME!

Hal, is that you?

Hi My wife does alot of baking and our Electric GE stove keeps shutting off randomly when she is baking in the oven but it always comes back on and is otherwise working fine. Would a thermal fuse act in this manner or is it most likely a control board or something else? Thank you

I have an old Caloric Ultramatic and after using the clean cycle it won't bake or broil it will only heat in clean mode. Could it still be a thermal fuse since it is still heating in the clean cycle? Thank you

thanks for useful inf , sir what would be happened if i bypass the thermistor either for safety aspect or cooling efficiency?

Hi there,I have a question.What is the difference between grooved pulley and sheave?

As a former G2 Apprentice, I have more experience in furnace repair, and installation.

This is helpful. Me and my supervising technician repair a furnace during my Gas Technician 2 Apprentice.

Not a hard job... always comforting to have a pro walk through it. Thanks!

This is by far the best video on explaining how to diagnose and repair your own ice maker. Kudos to Vance. He also speaks slowly and calmly and helps you stay calm during what could be a very frustrating process, I think we should clone Vance. 😉