Hi. The lawnmower is just buzzing around and has no idea where it is. Once it's set to zone 1, it assumes it's always in zone 1, regardless of its actual location.

I'm not sure, but I have 650mm. 50mm between the wires

Hi. It's programmed to run 50% on each of the two zones. Sometimes it mowe zone 1, and sometime zone 2.

Hi. The posision of the wire is just below the tape. Not in the center of the mower

@@7171TBJ on the narrow passage you can see the wire is not below the tape, it is pushed to the side much more when the wires are so close to each other. My explanation for this is the magnetic field lines are pushed to the outside by the field lines of the other wire, they are repelling each other, the point where the field is horizontal is not exactly above the wire anymore.

I think it must have at least 80 cm straight stretch as it drives into the charging station, as shown here: jottacloud.com/s/000f140143192d4446786c650ea2e04f323

Jeg er delvis enig. Det er et problem som bare blir tydeligere og tydeligere

Sorry. I dont know

@@7171TBJ That's okay 😄 Thanks for the feedback

I think there can be some misunderstandings but I would check with support.

Still happy with it after a year?

I'm not sure if the ACS will detect obstacle above the ground. I'll test this summer (in May) when the snow is gone

Yes, to both questions

​@@7171TBJ in my case two zones of approximately 300+500 m2 (ca 3000 + 5000 square feet). When cutting in the zone of base station and finishing it will have a 50% chance of going into the other yard to come home? Then I should look at where I do the break out so possibility of starting to follow the wire at undesired place is as low as possible.

​@@i679n5You have right

I'm not sure, but I have 650mm. 50mm between the wires

Yes, I use 5 cm and it works

Er det en droneklubb?

My video only shows when it's searching for zones. It does not mow when searching. The only time in the video it cuts is from approx. 1:32 to 1:38. The rest is just searching for zones. I have had the mower for about a year and I am pretty happy with how it cuts the grass.

@@7171TBJ Thanks

I think it is level. See pictures; : photos.app.goo.gl/KgvmkmxxCZ5zAXFJ7

No. You tell it what percentage of total time per week it should be on the different zones.

Kermot I love that you give your robot sundays off

You must prevent the mower from entering the zone when mowing, so have as little opening to the corridor as possible. It should only enter the corridor when looking for the next zone.. Sometimes it may just hit the opening "accidentally" when mowing, so it will cut into the zone. I haven't had the mower for so long, so I don't know how often it will "accidentally" enter the corridor, but I expect it to happen. I have updated my picture of this project with arrows pointing at where I pressed "mark zone": photos.app.goo.gl/KgvmkmxxCZ5zAXFJ7

@@7171TBJ thank you

Your station is in the zone 2. But when you set up the zone, you defined each one at the beginning or at the end of the zone ?

​@@nicolasboileau1800 At the beginning of zone 1 and after the corridor at zone 2. See yellow arrows in picture: photos.app.goo.gl/KgvmkmxxCZ5zAXFJ7

Hi. My Landroid was it was programmed to mowe only zone 2 in this test. You can program Landoid how much of the total time it will spend on each zone.

You must prevent the mower from entering the zone when mowing, so have as little opening to the corridor as possible. It should only enter the corridor when looking for the next zone. And no, I have no problems with interference.

7171TBJ Many thanks! Ciao

No. It stop cutting when searching for the next zone, and it only enters the corridor when searching for next zone. I made the entrance to the corridor very narrow because I didn't want it to accidentally escape from the zone when its cutting the grass.

The Landroid searches for the zone and then begins to cut. Nothing prevents it from moving between the zones as it cuts. Thats the way the zones works. It's only a "stupid machine".

@@7171TBJ so does a the earea inbetween need weed wacked with a weed wacker?

Landroid needs at least 80cm straight path in front. See phott at the bottom right here": photos.app.goo.gl/KgvmkmxxCZ5zAXFJ7 The video does not show when it connects to the charger.

Yes!

Ok

Vinterflygingen med Mobula7 har hjulpet :-)

Hjelper så lite, ref. kommentaren min under videoen (Linsa er fysisk skrapt opp)

Kameraet på Mobula7 suger

Kom og bli med. Om noen minutter er det mørkeflyging

Kuttet kraftig ned på opptakene, så ja; mye venstre

Sint veps, vil jeg påstå

eller det

Nei, men jeg skal bli :-) Timer bak spakene må til