@@matthewbailey2969 no , just unbolt what I’ve shown on video , is only pressured when engine is running. And be carefully when you take the fuel rail out not to drop any dirt on the holes of the fuel rail.

I’ve put BERU brand (borg Warner), they come from the factory also.

Salut , doar ce spălasem mașina de aia era udă… sârmele de pe racordul flexibil le-am tăiat sa văd dacă tot mai face , și da tot se aude … înăuntru racordului flexibil este rupt și de aia zornăie.

@@grayslayers no , the pistons are closed, Check with your phone camera ….degrease properly with mr proper or something else … and then take your vacuum put a small rubber tube by the end of the vacuum suction with some tape , and then insert on the valve holes … and vacuum all the moisture and else . 👌

I forgot to ask, how did you depressurise the fuel rail before loosening the injector pipes?

Took me 2-3 hours and yes I’ve sprained in there because the valve where closed fully , be careful not to drop something in there, and I just unbolted the bolts from the pressure fuel rail… then when you put it back on just prime (contact on and of ) the fuel maybe 10 times and you good to go .

@SilviuGabriel1997 Hi, thanks for the reply, I actually did this work yesterday. My swirl flaps were sticking & throwing up an engine warning light. I cleaned the throttle body & the EGR at the same time. Thank you for giving me the confidence to do it myself. It really was simple to do & very satisfying!! I hope many more see your video & benefit from it, like I have.

No , only I’ve put the contact a few times 10 times or more … and has started back !

@@SilviuGabriel1997 thank you

@@SilviuGabriel1997​​⁠Which contact do you mean? The one in front or inte the back? And did you unplug the battery before doing all this?

@kurt-io5xi I mean you can put your ignition on and of a few times after you put back together everything, to prime the fuel and so on , and yes disconnect the battery. Good luck 🤝

@@SilviuGabriel1997thank you very much for the video and tips. It all worked out great and got rid of the fault code p2015 by putting the external bracket on to limit the movement of the flap motor arm.

Try to se on the back of the engine at intake manifold electric motor … if the arm small arm doesn’t move, you have a bad motor flaps

@@SilviuGabriel1997 it moves. i checked when egnition on it moves back and forth. do u have garage I can bring it there .

No , I’m abroad at the moment sorry

@@SilviuGabriel1997 Any suggestion? any oil, liquid or spray can be used to eliminate this issue. Please advise.

@@Amarjit999 cheaper options, try to replace valve solenoids and checking properly the waier cable , if is not going to work try to replace either electric motor or the entire intake manifold, maybe yours is clogged and stuck (open and clean if you didn’t done, cheap operation)

Not really… I just take it out to clean for better flow and prevent any buildup, you can see in the video mine was not full of oil inside the electric part… maybe when oil gets inside the electric part, you will get a warning

Hi , the exhaust is still stock , only the ❌dpf and cat ❌ it’s empty! No modifications on the exhaust. Cheers Cut , empty… good to go 🤫

Nope !

If you use a toothbrush the chances are to damage the lids inside, try only pressured water souped etc.. if it’s very dirty then use a soft brush .

Hi, would a small ultrasonic ( jewellery cleaner) be ok with washing up liquid in water ?

Hi , Yes will be ok, but use a soft pad in my opinion . 👌

@@SilviuGabriel1997 Thanks Silviu

Whats the point of this rubbish 🙄

Simply just clean it and put it back on… 👍 it may work

With what

Yes after couple of days my dpf light check engine and glow plugs come on the dash straight…. I’ve tried to clean the dpf but was more than 85% clogged, that’s why engine very poorly running and white smoke , I’ve done dpf and cat delete! And clean the EGR , Now engine runs very smooth an freely (can breathe better) this was in my case, not sure in yours. I hope I’ve helped you

Bravo!

I’ve used mainly water and soup , you can use different products but it’s going to be the Same result ( let it dry)

I heard electric contact clearer is the best

What’s the point of this, when you didn’t show the cleaning process??? bell end!!

Which soup, chicken, vegetable or mushroom? lol@@SilviuGabriel1997

Stai liniștit !

I tried with welding but was a total mess 😅 I need to Learn more... but I’m very satisfied with screws , very strong and straight to .