They were a good combine. Worked on lots of them

Great update!

I think the ez steer issue is as you engage the motor it's dropping the voltage a bit to low for an instant. It's usually either needs an even bigger wire run direct from battery to controller, or all connections need a thorough cleaning

I'm thinking go from 3 combines to only 2. This fixing is getting to be bullshit

Quite the tank mix 😂😂

Lost of stuff if leaving dose that mean lots of stuff is going to be arriving? 🤔

The " aircraft " needs a wiper rubber

👍👍

Live and learn every day

I thought Rob always usually buys your equipment you sale!😂

I was just going to say 345 is not roundup resistant. 354 is the truflex variety. I have grown both varieties

did you know that john deere had a PTO harvester built here in australia for the australian farm ,you tube it john deere 1051 pto harvester

10:55 yes, i like and coment your video. Ok? Its very good 😊

Are many in your area growing beans?

I had really high hopes on seeing the 7721 run a lot of acres and see it perform. Little saddened to see it go

The ladies are loving this video.

Great video Nick anxious to see the combines rolling again

Kind of like what happened at Rollag on the Anderson farm. Good bye axil flow. 7700& 8820& a blast from the past JI case 960

Bye 7721 👋

Brilliantly mint brah!

Glad to see you packed the essentials, toilet paper. For when it hits the fan.

🤣🤣🤣

Awesome seeing the 1682, 2188, & 9600 legends out harvesting

How do you set your 9600 for canola?

When you get a bale without mesh on it check the top roller. The belts "skip" the gap at the top and the mesh will get caught/wrap the rear top roller. That is most likely what caused the bearing to fail. I stop and check that roller as soon as I have a bale with wrap torn off, even if it is just one side of the bale. It is easy to get the wrap off before it becomes wrapped really tight on the roller. On the JD 9600 plug. You can get a small chain wrapped around the header frame just at the edge of the feeder house. Make a loop to attach a cable come-along there. Then raise the header all the way up there will be a pretty straight shoot to the cylinder drive pulley. (You need the feeder house up anyway to dig out the plug.) You can get the end of the cable come-along on one of the bottom spokes of the cylinder drive pulley. You can then roll the cylinder back with the come-along. If your luck is like mine you will have most of a round bale stuck in there. LOL. P.S. I assume your running the the front drum of the feeder house locked in the down position??? That way you will normally plug the front of the feeder house before the cylinder.

Yeah, i use little two ton chain come along. Go under the cylinder around the back and hook it to a chain it to the bottom of the header. Once perfected unplugging becomes about and 15 minute job

Those Auger headers work ok for canola? Early frost and only having 930 auger headers are my two fears when it comes to straight cutting.

Nice shots guys! Harvest is a family affair. I love those golden hour shots. I picked this video back up about in the middle for the drone shots with the music. Neat segment, but I had to check to make sure what channel I was on... Similar to the harvest stuff my buddy @Rosso_Dabosso does on his channel, but in eastern South Dakota. Thanks for sharing!

comment

Yessir, yessir Nick, knock it out hoss💪🏻

Have fun with that 9600, my uncle plugged his 9500 solid one year in straight cut canola and it was a 2 day process to get it unplugged. That being said I plugged the beater right solid on our 2188 this year in straight cut canola and it was a 12hr job to get it unplugged so it’s half dozen of one 6 of the other. Either at the front or the back of the machine. Either way youre sitting under or inside and cussing the whole time haha

My barley straw is doing amazing as well. Don't even have half the field baled and I was at 200 last night.

I don’t like straight cut canola. Seems like a liberal invention that Trudeau made to make everyone gay. No one by me ever straight cut it before Trudeau came around. So I will never straight cut my canola because I’m not a gay liberal

I was helping a farmer unplug his John Deere pull type, two hours with a sawzall and knife, cramped fingers and making hardly any headway. I got him to bring a power plant and a drill with a half inch bit. I drilled hundreds of holes into the rope like plug in a half hour, got into the tractor fired up the combine and out came the plug. Just a little smoke.

I grew the same canola. Except I combined it for fun. Lol. Didn’t even get a full semi load fs

Nick there is a tool that goes around the roller that follows the belt and hooks to the frame. You use it to set the bale shape sensor viewing a certain address on your monitor. It’s all explained in the operators manual. I’ve been watching you bale for a while and my O.C.D. Wants me to adjust your sensors😂

Great video keep them coming

Love the drone footage ❤. Gives such a great perspective on the ground being covered! Great job combining Keegan!!

Wasnt long ago the 2188 was the flagship of the fleet! Expanding fast bud!

Makes it all worthwhile when you get a good yield from your crops 👌 think you may have enough straw bales for winter yet 🤔 gonna take some time cart them all home 👍

Hey nick get a cylinder wrench. Will change your life.

Invigor canola be like never heard of super glue

Great video - great looking crop of canola!

lol super glue

John Deere wins again!

Have to pick up a 2162 (fd70) for the ol 8010. They go pretty cheap on auction already and work great

Good to hear that your canola is yielding good

Good luck. Thank you, keep working.

Wreck it ranch part deux!! Lol😆 foo foo 😂

Plug a 9610 one time with soybeans. Not much fun , lot of cutting with a good knife...