Пікірлер
@jexmartinez9343 16 күн бұрын
I added blue painters tape to the miter aluminum slider and it worked great. But your method here is way to awesome. THANK you ..
@krzysztofb.6827 25 күн бұрын
Thanks man, im just unboxing same thicknesser and your video helped a lot. All the best
@diycompanion 25 күн бұрын
You're welcome. My pleasure🥰🥰
@stephenbustos 27 күн бұрын
I wouldn't waste my time doing this. You can simply buy the right size replacement miter bar and screw in the pieces. Especially for the Dewalt. You can find a bar for around $20. Simply screw in the miter gauge to the new bar, and you're done. But, if that wasn't in existence, this video would be perfect to help solve the problem.
@diycompanion 27 күн бұрын
🥰
@WoodenWonders99 Ай бұрын
Totally crap, but you still can keep the black part. I sent everything to recycling. You could replace the bar, because it is not expensive, but you did a great job.
@erhardnix9586 Ай бұрын
Self-adhesive PTFE on one or both sides does the job too, but needs only 2 minutes. And it works the whole way long, not only when the gauge is full in the slot. Sry for my bad english :-)
@grandibig9161 Ай бұрын
Great solution, but I really don't understand why De Walt doesn't solve it at the factory for years, people have been complaining about this problem, why are we forced to solve this problem ourselves, and we have a rather expensive tool from De Walt
@diycompanion Ай бұрын
I get it-it’s frustrating DeWalt hasn’t fixed this. That’s why I shared this solution to help out. Hopefully, they’ll listen to feedback and improve future models😊😊🥰
@gregorymacneil2836 Ай бұрын
Great Video and project-I am going to fix my sloppy DeWalt gauge tomorrow morning.
@diycompanion Ай бұрын
Appreciate your great feedback 🥰🥰
@gregorymacneil2836 Ай бұрын
@ I have a very good shop for fasteners so I will look to see if they have nylon set screws.
@diycompanion Ай бұрын
Yes, nylon screws may work better. Keep in mind that Extra care should be taken with the side walls of the groove. Precise screw adjustment will be needed! 🥰
@Toni-oy5gu Ай бұрын
Take it back! If you had all sent them back perhaps dewalt would have fixed it instead of you spending more time and money solving the issue. Duh!
@diycompanion Ай бұрын
🥰
@kalervohamalainen4369 Ай бұрын
Educational video. Very good. Now I realize how important this was. And how nice it was to watch without the terrible music. - Thank you!
@diycompanion Ай бұрын
Appreciate your great feedback. Thank you .🥰🥰
@donhuffer5167 Ай бұрын
Never use it again. They are worthless except for rough cuts.
@steven_vogt Ай бұрын
You perseverance, ingenuity and sketchup skills really are admirable but sorry, the factory DW miter gauge does not deserve so much effort and time. A couple of layers of blue masking tape fixes the slop issue in 30 seconds. The accuracy of angles will always be a bit hit and miss anyway (not least because you tried to set square to the throat plate and not the blade?!?! 😳 ) The factory fence is too small to provide proper support. ✌
@Billy-in7rl Ай бұрын
Ok until you slide out of track which you do for cutting larger pieces putting the ball screws just at each end flaws the idea
@diycompanion Ай бұрын
Thank you for your feedback! The plunge screws were positioned to suit the light work I typically do. However, if you're planning to handle heavier tasks, you can adjust the screw placement to better suit your needs.🥰🥰
@whar2010 Ай бұрын
What a shame, you have to fix such an expensive piece of equipment. Shows you are paying for name, not necessarily quality.
@diycompanion Ай бұрын
You’ve got a point there. With construction table saws, some wear and tear is pretty much expected. But honestly, this one stands out because its performance is on par with cabinet table saws. For its category, it really delivers exceptional results.🥰🥰
@whar2010 Ай бұрын
@ I had one I just sold because it was no where near a cabinet saw performance. Honestly, I have an old $50 Delta that is pretty equal to the Dewalt I sold. Just didn’t impress me for the price. But overall it was an average with contractor type saw. Not really any better and certainly not worse. But just my opinion after using it for a year. I had a larger Ridgid saw a few years ago, far superior saw, but it wasn’t portable as far as going from site to site easily. I replaced it with the Dewalt. Maybe I expect to much, ha ha have a good day.
@xawerytrabka8813 Ай бұрын
THIS IS IT!!!!
@diycompanion Ай бұрын
🥰
@jamesdavis9306 Ай бұрын
Brilliant solution thanks for the idea I can confirm it works on my evolution Rage 5
@diycompanion Ай бұрын
I appreciate your great feedback. Thank you 🥰🥰
@JohnColgan. Ай бұрын
Great solution
@Oops-IMeantToDoThat Ай бұрын
Great conceptually. However, it will only work if the entire track is inserted. Worse, even if you added more set screws. since the set screws are metal, as you use it, you wear away the surface of the track itself. Better to just use tape on track. Quicker and repacks as the tape wears (softer than metal or ceramic).
@deathmetalsl Ай бұрын
I'm hoping to purchase this saw in the near future so this is an invaluable video to me! Thanks for the upload.
@diycompanion Ай бұрын
I am grateful that my video has been helpful to you. 🥰🥰 KIT. Thank you
@reinerjust Ай бұрын
Outstanding, the first who found a solution without buying a new gauge. Well done
@diycompanion Ай бұрын
Appreciate your great feedback 🥰🥰
@somorovski 2 ай бұрын
That's THE BEST video I ever seen about "what to do" about the gap at the miter gauge on table saws!!!!! All the rest is crap!!!!
@diycompanion 2 ай бұрын
Thank you so much for your great feedback 🥰.
@hectorfox9710 2 ай бұрын
Exactly! I have the same problem since I've bought a dewalt table saw. I think your way is ONE on YT. I’ve never seen that before. Thanks so much for your job. Now I know what to do. I will sleep calm tonight.💪👍👏
@diycompanion 2 ай бұрын
Thank you for your great feedback. 🥰
@timlist4173 2 ай бұрын
The saws rail is not consistent in width along its run. Take that into consideration when adjusting it.
@diycompanion 2 ай бұрын
🥰
@mr_torx 2 ай бұрын
Great video, great explanations!
@diycompanion 2 ай бұрын
Thank you for your great feedback 🥰
@williamkilpatrick101 3 ай бұрын
Great video. I've never seen these before and they look the perfect solution. Thanks a million and I will definitely be looking to see if I can apply this to my mitre slots.
@diycompanion 3 ай бұрын
Thank you for your great comment🥰
@martinwilliams9098 4 ай бұрын
Excellent tutorial,learned something Thank you
@diycompanion 4 ай бұрын
That's exactly what I hope for. It's a pleasure. Thank you.
@martinwilliams9098 4 ай бұрын
@@diycompanion thank you
@RossRawlins 4 ай бұрын
Where did you get the ball plunger screws from?
@diycompanion 4 ай бұрын
You will find those in varying sizes at your nearest hardware stores. If not there, check the 'AliExpress' online marketplace; there, you will find many more of this item to suit your purpose. Just make sure that it is the right size. Thanks!
@ENGFREEMAN 4 ай бұрын
thanks
@diycompanion 4 ай бұрын
🥰❤️
@ENGFREEMAN 4 ай бұрын
good job ... thanks
@diycompanion 4 ай бұрын
🥰❤️
@ENGFREEMAN 4 ай бұрын
@@diycompanionkindly can you share with me from any site you bought these ball headed plunge screw? ... Regards
@diycompanion 4 ай бұрын
You will find those in varying sizes at your nearest hardware stores. If not there, check the 'AliExpress' online marketplace; there, you will find many more of this item to suit your purpose. Just make sure that it is the right size. I hope this link helps www.aliexpress.com/w/wholesale-spring-ball-plunger.html?spm=a2g0o.best.search.0 Thanks!
@ENGFREEMAN 4 ай бұрын
@@diycompanion thanks for replying
@diycompanion 4 ай бұрын
🥰
@chrisnagy 4 ай бұрын
Excellent demonstration of the blade/grain cutting direction.
@diycompanion 4 ай бұрын
Thank you 🥰❤️🥰
@hugosodery2012 6 ай бұрын
Ficou ótimo, parabéns pela criatividade, qual o nome desse parafuso que você usou?
@diycompanion 6 ай бұрын
Obrigado. O que você quer dizer com 'parafuso'? Você poderia apontar o ponto de esfrega do playhead para que eu possa explicar. Thank you. What do you mean by 'parafuso'? Could you point out the playhead scrubbing point so I can explain.
@hugosodery2012 6 ай бұрын
Ball headed plunge screw é com rosca M4?
@diycompanion 6 ай бұрын
Yes. It's called 'Ball headed plunge screw'. different sizes are available at local hardware shops.
@hugosodery2012 6 ай бұрын
Ok, muito obrigado!
@diycompanion 6 ай бұрын
🥰
@veritas4us 6 ай бұрын
Nice job
@diycompanion 6 ай бұрын
Thank You 🧡🧡
@brienpike4220 7 ай бұрын
Nice engineering skills on display here. Great solution to the problem!
@diycompanion 7 ай бұрын
Thank you so much for your great feedback 🥰❤️❤️
@FrankSurateau-h4y 7 ай бұрын
Un pied à coulisse n'est pas fait pour tracer ??????
@uryansynth 7 ай бұрын
Thank you for your work with this vid, simple, easy and helped me to make my decision what planer to buy :) Thank you again :)
@diycompanion 7 ай бұрын
You are welcome Sir 🧡🥰
@bertvg86 7 ай бұрын
Great unboxing video! A lot of people put themselves in every shot or overe/underexplain things. This is clear, concise and shows everything you need to know without annoying interruptions, well done!
@diycompanion 7 ай бұрын
Thank you so much for your great feedback.🥰🧡🧡🧡
@Владимир-э9ь2г 7 ай бұрын
Спасибо😊❤
@diycompanion 7 ай бұрын
Добро пожаловать, сэр. Спасибо за просмотр. You are welcome Sir. Thank you for watching!
@acamon 7 ай бұрын
This is a really helpful video, thanks! I love makita tools but their instruction manuals are awful. Just bought this tool and your video is making my life a lot easier!
@diycompanion 7 ай бұрын
It's a pleasure 🧡.
@mihailungu8106 8 ай бұрын
Simple and technically impeccable! Subscribed.
@diycompanion 8 ай бұрын
Thank you so much 🧡🧡🧡
@magamimi8429 8 ай бұрын
Price brother
@MrKen-wy5dk 8 ай бұрын
At 6:30 your hand is basically out of frame. What were you doing? Were you pushing on the fence? Thank you for a great video.
@diycompanion 8 ай бұрын
Hi Sir, are you sure about the time (6:30) that you have mentioned? I guess your thought was 4:30. anyway at the 4:30 mark in the video timeline, I was utilizing the rack and pinion method to move the fence. hopefully that's why my hand was not visible. If you want to get more information regarding this table saw, please watch my unboxing video of the table saw. here is the link for your convenience. kzbin.info/www/bejne/ioHZp2CQn8iImJY thank you for your great comment.
@a.b.l_m.s.n 8 ай бұрын
What is the horsepower of this model?
@diycompanion 8 ай бұрын
Having 2000 Watt Motor
@a.b.l_m.s.n 8 ай бұрын
@@diycompanion I mean horse 1.5 ore 2 ?
@diycompanion 8 ай бұрын
Around 2.5hp
@a.b.l_m.s.n 8 ай бұрын
Can we install cmt blades? The inner diameter of the tree is 25.4 On the Dewalt DWE7492 table saw??
@diycompanion 8 ай бұрын
I don't have CMT blades, but as far as I know, you can install CMT blades. However, the issue lies with the inner hole diameter, which should be 30mm for compatibility with this machine, not 25.4mm. If you have a blade with 25.4mm inner hole, one option is to use a blade bush (steel ring) to reduce it to 16mm. It's worth nothing that using these bushes is not recommended by either the machine manufacturer or blade manufacturer due to safety concerns.
@ronaldnayman4841 8 ай бұрын
Send your design to Dewalt - Please.
@michaelzarutsky3624 8 ай бұрын
Overkill much? 1. Just slide it into the slot to undo the screw with thread lock. 2. Use a cotton swab + isopropyl alcohol to degrease the sides. 3. Use PTFE tape on one side. Cut the excess off with a blade. 4. Use the cut off part of the tape on the other side - cut the excess off... 5. Rub the tape with a dry cotton swab to ensure good adhesion. 6. Done. Less than 5 minutes total. No SketchIp skills, massive vise, drill press or fancy screws required...
@7ajidanger 9 ай бұрын
Great job 👏
@diycompanion 9 ай бұрын
Thank you
@shawwoodworkingdiy 9 ай бұрын
Awesome thumbnail bro! 👌👌
@diycompanion 9 ай бұрын
💚❤️💚
@seanparrish7293 9 ай бұрын
This is awesome! Nicely done
@diycompanion 9 ай бұрын
Thank you Sir!🥰❤️❤❤️
@fishcakes2 10 ай бұрын
Very clever ! I just run a bead of super glue and then sanded to fit but your method is a professional way !
@diycompanion 10 ай бұрын
Thank you Sir.💚🧡💚
@MrKen-wy5dk 10 ай бұрын
Why don't people who use fast-forward in their videos mute the audio so we don't have to listen to the chipmunks?
@pieroh60 11 ай бұрын
Perfectly presented upgrade. I didn't know a plunge headed screw before....
@diycompanion 11 ай бұрын
❤️
@AugustSpriggan 11 ай бұрын
Whats that thing on 24th sec?
@diycompanion 11 ай бұрын
SATA - SSD hard drive cable with 2.5" HDD caddy (Additional option)
@AugustSpriggan 11 ай бұрын
@@diycompanion, I got 15ach6 model and need extra ssd, but i dont have a clue which one to buy specially for my laptop
@diycompanion 11 ай бұрын
Before upgrading, it's essential to observe the hardware settings in your laptop, even if the model number matches. Different configurations may exist depending on factors like the market, price etc. For instance, in this laptop, there are three slots for hard drives: (Non-RTX 3060 models:) One 2.5" drive slot, supports 2.5" HDD (up to 1TB). One M.2 2242 PCIe Gen 3x4 slot, accommodating M.2 2242 SSDs (only a small size of SSD (22mmx42mm) can be installed up to 512GB). One M.2 2280 PCIe Gen 3x2 slot, supporting M.2 2242/2280 SSDs (either 22mmx42mm or 22mmx80mm, up to 1TB). Note that the 2.5" drive slot and the M.2 2280 slot are mutually exclusive, meaning they cannot be used simultaneously due to space constraints. To determine what's currently installed in your computer, you can use Device Manager or other relevant applications. Alternatively, carefully opening the back cover and observing the hardware can provide this information. Once identified, you can decide what to purchase. For example, if your computer is equipped with only an M.2 2242 SSD, you have two options: you can either install another M.2 2280 SSD (up to 1TB) or install a 2.5" HDD - up to 1TB (requiring caddy components for HDD). This information is provided to the best of my knowledge, but it may not perfectly match your computer's specifications. I recommend thorough observation and research before proceeding with any upgrades. Cheers!
@AugustSpriggan 11 ай бұрын
Thanks a lot, man! Since I dont have the laptop at my place right now, I can not take a look under the hood. However I made my own research and came to the same conclusions just like you did and decided to buy SSD M.2 2280 1TB Hikvision E3000 PCIe 3.0x4 NVMe 3D TLC My gaming 3 is 2021 model without Thanks again a lot for your competence and generosity!
@jayantbhatt8795 7 ай бұрын
@@diycompanion What is its use? Why is it there? I've been wondering that since my laptop arrived. Please help me understand