Do you also know how to make it so low beams stay one when high beams are turned o(2001 dodge durango owner here)
@Stoneyx4202 ай бұрын
@@HunterDarkWolf that's what this video shows not sure what your asking
@HunterDarkWolf2 ай бұрын
@Stoneyx420 oh i thought this was just on the fogs alone so doing this will also make high and low beams stay on?
@Stoneyx4202 ай бұрын
@@HunterDarkWolf all 3 at the same time when you high beams are on
@HunterDarkWolf2 ай бұрын
@Stoneyx420 just by cutting that pin...so many complicated vids and then you save us all with just the simple solution
@rickstride72692 ай бұрын
very well explained. i only wish u had a camera holder. i am old and visual aids are very helpfull.
@sleekSquirrel3 ай бұрын
what is that speedometer from?
@Stoneyx4203 ай бұрын
@@sleekSquirrel 83 xr350r speedo
@loveyourpitbull3 ай бұрын
Thanks for video! I used a 3/8 tap. About 2 in deep, threaded rod into bolt and a 3/8 coupling nut to do the pulling on various spacers. Worked like a charm on one stuck rusted swingarm bolt.
@colebz4204 ай бұрын
Can't pound it and hold the camera at the same time? Rookie.. lol jk thanks for the vid
@sk814esk4 ай бұрын
Muchas gracias amigo. Muy bien explicado y facil de entender. Ni siquiera necesité usar el traductor.
@fernandocdl19685 ай бұрын
where do you get your seat covers?
@MikeMcfarlane-by9pg5 ай бұрын
No one wants to show how to remove the panel from behind the driver's seat in left side of the extended cab to replace the speaker in it
@MikeMcfarlane-by9pg5 ай бұрын
The other side is not a door it is a solid panel
@wearzymaan15415 ай бұрын
Thanks
@Live_it_Love_it-506 ай бұрын
I’m just rebuilding my pump at the moment I just looked at the explode after watching your video and noticed you put the seals in the wrong way round as the spring lip should be facing the impeller
@ericsarmiento55747 ай бұрын
Before y’all did this when the fog are on with the lows did the high beam indicator turn on?
@Stoneyx4207 ай бұрын
No the high beam indicator only comes on when the high beam is on
@ericsarmiento55747 ай бұрын
I guess something’s goin on with mine cuz when I turn on my fogs the high mean indicator lights up
@marcbrazzers8 ай бұрын
The edge and orings should use loctite 518 (or permatex equivalent), not black rtv. Also, i also re-used old thrust washer as mine was too thick as well. Also, you need to use loctite 518 around the surface of the oil seal and put grease inside the lip as per the manual.
@carsonlillig530711 ай бұрын
Any trick to remove the bearing from the jet pump housing? Just picked up a 92’ sl650 and nothing has been replaced or rebuilt.
@Stoneyx42011 ай бұрын
Hammer and a punch make sure if the baring is still in tack to hit it on the outer part of the baring otherwise it will probably make a bigger mess
@MyTimmy7511 ай бұрын
What you do. Buy a set of regular boots for mxz's They're one piece rubber. And angled in a way that your air box will sit flat. You;ll never blow an engine again., Or have air leaks ;) You won't lose performance .
@chicoferraz6611 ай бұрын
Greetings.. Do you have a video on how to remove and re-install the impeller onm a Polaris Virage Tx ? Thanks.
@Stoneyx42011 ай бұрын
I unfortunately do not but from what I looked up online it looks the same as this ski all the parts are the same
@chicoferraz6611 ай бұрын
@@Stoneyx420 thank you sir.
@nabl1418 Жыл бұрын
How many inches high is your front mounting bracket? The one that bolts to the gas tank bolts.
@nabl1418 Жыл бұрын
I want to do this on my 2000 skidoo summit. How many inches higher is it?? Did you raise your handlebars also?
@Stoneyx420 Жыл бұрын
Mine seat hight ended up being 4 to 5 inches high ride hight to my seat you don't need to go that high if you don't need I'm 6'.5" and I can sit on it with my knees bent at a 90 and yes I got a 4 and a half inch riser then added another inch and a half with some plastic blocks and it was perfect for me really depends on how tall you are
@nabl1418 Жыл бұрын
@@Stoneyx420 did you need to get brake line and throttle cable extensions at that handlebar hieght?
@Stoneyx420 Жыл бұрын
On this sled I did not but I put the set up on a 99 and needed a throttle extension
@jacoblatour6192 Жыл бұрын
What’s the point to this? I’ve heard they save weight or that they are stronger? If it does save weight does anyone know how much?
@Stoneyx420 Жыл бұрын
No clue I did it because the previous owner was a idiot and rode it with the sprocket bolts lose and disk bolts lose and ate a hole in the original swing arm also the shocks are sopose to be a bit of an upgrade compared to the 03 shocks
@dannyorsello8668 Жыл бұрын
Very interesting, I will take a look.
@tirospcpdeensenada2197 Жыл бұрын
Good afternoon, what oil do you use to put the black oil bottle in the jet cone, what is it and what grade?
@Stoneyx420 Жыл бұрын
It's just some canadain tire outboard gear oil it's just 80w-90
@astr0creep6x6x6 Жыл бұрын
This voice sounds SOOOOOOOO familiar. I am scabbing a cfr450 front end on a 1000 Sportster and was just planning out the work to scab the cfr460r swingarm onto the bike.
@Brick181 Жыл бұрын
I have an 03 polaris genesis, any tricks to remove the impeller? Mine is stuck.
@Stoneyx420 Жыл бұрын
Just put in the vice like i did and use A braker bar try that if it won't put your favorite penitent down where the removal tool go's and let it sit over night
@Brick181 Жыл бұрын
@@Stoneyx420 First off thank you for the reply, but I wasn’t clear. I’m trying to take off the housing that holds the impeller to the engine. I saw videos of people using 2x4 or breaker bars, but mine is stuck so bad, nothing has worked. Any tips would be appreciated. Let me know if you need pics?
@lildoggo7289 Жыл бұрын
It looks to me like the seals on the exploded view from Polaris are the opposite of the way you put them in
@jeffreyhagy1666 Жыл бұрын
What size tap and bolt did you use?
@Stoneyx420 Жыл бұрын
Off the top of my head I can't remember but just go threw your tap set and find the one that looks like it will cut threads In the end of the swing arm bolt
@davidovicc2 жыл бұрын
Put them both in the trash sir. Go get 😊be running
@construction752 жыл бұрын
Did the crf 450 swingarm bolt right up to the cr 250 with no problems?
@Stoneyx4202 жыл бұрын
It just bolts right on no issues at all
@alexmembreno42492 жыл бұрын
What happens if you put the wear ring with the lip down 😅
@Stoneyx4202 жыл бұрын
It won't seal properly to the hull when you put your pump back on and could cause power loss wile riding
@alexmembreno42492 жыл бұрын
😅 men going to have to buy another one 🤦♂️ didn’t notice until I went back and read the book and new oil as well 😅 🤦♂️
@shannonwilliams6012 жыл бұрын
That's not rebuilding a jet pump that's just replacing the shaft and racer bearing
@andrewcalk878 Жыл бұрын
And wear ring. That is rebuilding the jet pump lol
@1991enduro2 жыл бұрын
Nice
@joshuaott28002 жыл бұрын
is my ride supposed to just come out like that
@Stoneyx4202 жыл бұрын
Your ride? You mean the impeller shaft?
@pcduc642 жыл бұрын
What size battery did you install on it
@Stoneyx4202 жыл бұрын
The smallest profile 130cca battery I could find witch was a Yuasa ytz7s
@pcduc642 жыл бұрын
Where did you mount the start relay and rectifier
@Stoneyx4202 жыл бұрын
Ended up putting it back in the air box because I coild not find a small enough battery to fit in air box
@curtbeauchamp84412 жыл бұрын
Same shaft you just didnt install it right
@Stoneyx4202 жыл бұрын
No the new thrust washers from the kit I bought was a diffrent thickness then the original one I just re used the original thrust washer . Side note are you Ron Beauchamp son? Turn left!!
@dylanbourget93982 жыл бұрын
Did you align the drive shaft?
@Stoneyx4202 жыл бұрын
No you don't need to align the drive shaft unless you take the engine out the customer just waited way to long to replace the barings and it cause play in the shaft and that made the wear ring and impeller to wear out they drove it all last summer with no issues they brought it back in the winter to get it winterized and said it worked way better then it use to
@jeffcee94572 жыл бұрын
Very helpful thanks for taking the time out to sharing about to buy a ski with pump issues
@Stoneyx4202 жыл бұрын
No problem got a few other pump rebuilds for a few other skis as well
@CarriedByCam2 жыл бұрын
Could this ever cause any damage or malfunctioning anywhere?
@CarriedByCam2 жыл бұрын
Do you think this will work on an 08 Dodge Charger R/T? Also would doing this ever cause any damage to anything?
@Stoneyx4202 жыл бұрын
No clue never done it on one of those
@Stoneyx4202 жыл бұрын
Just damages the relay because your cutting or bending the one prong but if your consigned about it I wouldn't do it
@dirtbikeheaven11292 жыл бұрын
I’ve encountered a stuck swingarm bolt on two XR-250’s. I removed the gas tank and laid the bike on the left side. After removing the swingarm nut, I began spraying the end of it with penetrating oil. After a day of this, I sat the bike upright and spun the swingarm bolt with a pneumatic impact wrench. The bolt would barely turn so I laid the bike on it’s side again and continued applying penetrating oil while continuing both of these procedures.. While performing these procedures, I would periodically try driving the bolt out with a hammer and brass punch. Once the bolt began moving, I continued driving it out and in about an inch on each side. After about three days of this, the bolt was loose enough to be removed.
@Stoneyx4202 жыл бұрын
Yup that works too iv done it that way befor I found the puller tool I made helps speed the process up
@MyTimmy752 жыл бұрын
Ebay my friend. And you can rebuild the other 700 :)
@Stoneyx4202 жыл бұрын
At the time this happened there was nothing on ebay but thanks
@MyTimmy752 жыл бұрын
@@Stoneyx420 Awe thats too bad :/ Well. I guess of anything. You've got yourself a good Parts sled in the mean time :)
@LSDdreams8082 жыл бұрын
I have a 2002 mxz 700 i got for $600 with blown engine new piston an jug an she is the most soild sled iv ever had
@mattbasson95912 жыл бұрын
you should delete this video. Geez!!!
@Stoneyx4202 жыл бұрын
Where is your video?
@sachac54353 жыл бұрын
looks like it should fit the 1990 600r im picking up tomorrow...
@sachac54353 жыл бұрын
hoo hoo lol!
@dinocracchiolo20403 жыл бұрын
Ddisclaimer. Does not work with 01 dakota 4.7!
@marcbrazzers3 жыл бұрын
How did you pound those two bearings out? Pound outside in or from inside out?
@Stoneyx4203 жыл бұрын
From the inside out if you do it the other way it will be hard to get out
@genderization3 жыл бұрын
The ribbon and the carrot
@cv8z2313 жыл бұрын
Well I hope this helps getting my 92 and 93 xr600r swimgarm bolts out cos they feel like they are in there to stay.
@sanjaypradhan17193 жыл бұрын
I have xr 250r 1999 but my bike has old frame !! My question is how to make it electric conversion so that i can i start it with self start and does it bother to takes any stress to my bikes engine or not ? What can be done !!
@Stoneyx4203 жыл бұрын
Iv never hard of anyone doing a 250 electric start only way I could see it working is if you got your self a trx250x engine and modifieing your frame to fit that engine. I know with the 400s you can take a the one side of a 400ex bottom end and crank and put the xr400 kick start side on said bottom end and have an electric start/kick start or do what the guy did to this bike and just slap a 400ex engine in a xr400 frame and go but as for the 250 never heard of anyone doing it
@project4stroke8763 жыл бұрын
what led headlights are u using? I hooked up a regulator same one u did. and my led light bulb burnt out almost instantly
@Stoneyx4203 жыл бұрын
I don't have a led in the stock headlight just the 2 square leds they came from Princess Auto if you watch my second video I show why this set up won't work
@Stoneyx4203 жыл бұрын
In the second video iv unhooked the leds from the stator and went and got a cheep battery to run them instead if you continue to run this set up it could potentially fry your stator unless you can add an extra winding on your stator or get a aftermarket stator with a light winding on it already
@Mike-su8si3 жыл бұрын
Must be newer then mine cause mine doesn't have that lever but it is a old 110 similar to that one
@Stoneyx4203 жыл бұрын
Yes I'm not sure this will work for the round fenders the kill switchs normally only stick if the tractor has been sitting out side for a long time like this one it sat out side for 5 years have you check to see if your points are clean and properly gapped?
@Stoneyx4203 жыл бұрын
There is also a kill switch on the gear section the shifter needs to be pushed down all the way for it to have spark
@Stoneyx4203 жыл бұрын
Also your condenser for your points could have gone bad
@Mike-su8si3 жыл бұрын
@@Stoneyx420 no i didn't know crap about those yet mines a square fender 110 the engine is a black 8hp Kohler
@Mike-su8si3 жыл бұрын
@@Stoneyx420 pushed down so not just in the middle on n I don't have to hold the brake or nothing do i