very well explained. i only wish u had a camera holder. i am old and visual aids are very helpfull.
@jeffcee94572 жыл бұрын
Very helpful thanks for taking the time out to sharing about to buy a ski with pump issues
@Stoneyx4202 жыл бұрын
No problem got a few other pump rebuilds for a few other skis as well
@sk814esk4 ай бұрын
Muchas gracias amigo. Muy bien explicado y facil de entender. Ni siquiera necesité usar el traductor.
@Stoneyx4203 жыл бұрын
2 more videos coming out this week be sure to check them out as well thanks guy's
@marcbrazzers8 ай бұрын
The edge and orings should use loctite 518 (or permatex equivalent), not black rtv. Also, i also re-used old thrust washer as mine was too thick as well. Also, you need to use loctite 518 around the surface of the oil seal and put grease inside the lip as per the manual.
@tirospcpdeensenada2197 Жыл бұрын
Good afternoon, what oil do you use to put the black oil bottle in the jet cone, what is it and what grade?
@Stoneyx420 Жыл бұрын
It's just some canadain tire outboard gear oil it's just 80w-90
@wearzymaan15415 ай бұрын
Thanks
@bikermike3 жыл бұрын
Nice job man! I heard the Yamaha's come with a Pratt and Whitney F119 PW 5000 jet propulsion unit. Only one though... is this comparable?
@Stoneyx4203 жыл бұрын
Yes faster then any boat out of the water
@genderization3 жыл бұрын
You're driving down the highway on a jet ski, when a wheel falls off. How many pancakes does it take to cover a doghouse?
@Stoneyx4203 жыл бұрын
@@genderization 6 er 9
@genderization3 жыл бұрын
Purple, cuz Ice Cream has no bones....
@hellzwings3 жыл бұрын
Great vid man thanks! Lots of details here you don’t find on other vids.
@marcbrazzers3 жыл бұрын
How did you pound those two bearings out? Pound outside in or from inside out?
@Stoneyx4203 жыл бұрын
From the inside out if you do it the other way it will be hard to get out
@alexmembreno42492 жыл бұрын
What happens if you put the wear ring with the lip down 😅
@Stoneyx4202 жыл бұрын
It won't seal properly to the hull when you put your pump back on and could cause power loss wile riding
@alexmembreno42492 жыл бұрын
😅 men going to have to buy another one 🤦♂️ didn’t notice until I went back and read the book and new oil as well 😅 🤦♂️
@colebz4204 ай бұрын
Can't pound it and hold the camera at the same time? Rookie.. lol jk thanks for the vid
@joshuaott28002 жыл бұрын
is my ride supposed to just come out like that
@Stoneyx4202 жыл бұрын
Your ride? You mean the impeller shaft?
@curtbeauchamp84412 жыл бұрын
Same shaft you just didnt install it right
@Stoneyx4202 жыл бұрын
No the new thrust washers from the kit I bought was a diffrent thickness then the original one I just re used the original thrust washer . Side note are you Ron Beauchamp son? Turn left!!
@shannonwilliams6012 жыл бұрын
That's not rebuilding a jet pump that's just replacing the shaft and racer bearing
@andrewcalk878 Жыл бұрын
And wear ring. That is rebuilding the jet pump lol