Holding that shit in the dark super annoying

So I just watched a video where they didn't remove the cam, just one bad rocker. Do you HAVE to remove the cam for this job?

Top work man you have great talent loved the video

thats govnor

What a bout Honda 1990 125 2 stroke

Ma Licciardello è un cognome Italiano

How much do you charge me to do that to mine? I feel like I won't be able to do it if I do it myself.

No, the impact gun clearly made all of the clutch bolts too tight because it broke on every single bolt without turning the bolt at all.Therefore, it was too f****** tight now, wasn't it?You're not very smart are you

That washer goes on the outside of the idler gear dummy behind the snap ring...

i can never start mine with my left leg lol have to use right leg then jump over. i had to put a rear master cylinder off a newer ktm to get good brake pressure

nice bike, i have an 88 and it looks exactly the same as yours. having a hard time finding any parts for it. currently has only 60psi of compression, ive never built a 2 stroke either so this is going to be a learning experience for me

How is JB Weld holding up?

Nice video. Thanks.

From my own experience I think they didn't let the motor worm up so the pistol expands more on the exhaust side and gets egg shaped and the rings break and fly around the cylinder before being destroyed.,it all happens in the matter of seconds. I actually locked up my 85cr250 and was able to sand down my piston to where the rings could slide out and around..hit the cylinder wall with fine grit almost polish and I'll be damed it runs fine,,,I sat on it for 10months looking fir a new jug then tore it apart and figured what the he'll I gotta lose??? I still can't believe it's running..gotta love dirt bikes :)....Rich S.😊

I wish u can do my jeep is giving problems with that

I had the same bike a few years back. The water pump housing corroded and had a huge hole in it. I fixed the housing with epoxy filler, shaped it real well and it worked great.

I was unable to remove the passenger side valve cover. There's a transmission fill tube behind it that doesn't allow for enough clearance to pull the valve cover off. I have a 2011 GC if that makes a difference.

I was looking at a WR that’s running for 2,500. But not sure it’s in a lot better shape.

solder and heat srink it

1986-1989 WERE RED AND WHITE RED SEAT WHITE PLASTIC GOLD RIMS BEFORE THOSE YEARS IT WAS YELLOW IN 1990 FOR ONE YEAR THE GRAPHICS OR PLASTIC WAS PINK SHOCK PINKISH RED SEATS GOLD RIMS PINKISH YZ250 ON TANKS AFTER THAT THEY SLOWLY TURNED BLUE YEAR BY YEAR UNTIL NOW THERE ALL BLUE CUSTOME YZ A YZ THATS BEEN BUILT AFTER FACTORY FOR MOTOCROSS OR EX GAMES MX FREESTYLE HAVE DIFFERNT YZ COLOR SCEAMS ALLOWING A PRODUCT SPACIFIC TO THAT RIDERS TASTE THOSE ARE EITHER CALLED PROTOTYPED YOU GOT TO REMEMBER YZ CAME INTOI MOTOCROSS AS A IDEA FROM RACERS ONLY A FACTORY RIDE READY TO RACE BUT THE HANDELING SUSPENSION ALL CAME FROM ONE MOTOCROSS YZ RIDER

Question which someone may know. With a white fuel-stained tank, how can you get the fuel stain out?

I bought an 87 yz250 non running for $200 new rear tire. Took 30 minutes got it running and once i seen it ran strong i replaced radiators the tank was cracked so i got a brand new overpriced clark tank and radiator shrouds and been riding my $800 dirtbike for 6 months now

Great 👍 job bro . thx

What are you using to hit the bearings in the trans

This issue seems to be so prevalent that i’m shocked that chrysler won’t cover a repair recall.

Had a bad engine noise and found all cams and many lifters in poor condition. Replaced all Cams and lifters and ended up with a rod noise from scorred piston walls. Ended up replacing the engine. Doe anyone need a deal on 4 cams and 24 barely used lifters.

I hope you have better luck with the hot rodz crank than I have locked up within 30hrs on one 35hrs on the other

Thank for making this video. One question. Do you really need to take the intake if you just need to do the right side? I didn't catch that from the video. One minute you are taking right side valve cover off the other minute you struggle to remove the intake. Let me know thanks

Have the same vehicle

I wonder what would happen if you put that motor on a bike with gears

This video saved me $3000 from a dealership! Thank you 🙏🏼

Nice bike. I have an 88 350, do you know where to find parts for this? I had to make a chain guard as well. Mine currently has 60psi of compression

How many miles on it cock face

You look like adin ross

Hey, i was wondering what kind of batteries you used?

I don't know if it was the best option to mount the bearings, if you end up hitting the piece anyway

Phuk bro...🤦🤦.....shyt🤦 how am i gunma do this

Great video , do you have the parts number of the parts you purchase from the dealership?

Hey, I have the top and removed off my two stroke and it still won’t kick. It seems to still be seized any advice?

Nice job

PCV valve is what it is on back of valve cover

so how can tell if i have a 1986 yz250wr by gears ?

Just bought one of these bikes good to know the case covers ar worth more then what I payed for it haha sweet videos man keep up the good work

How much in parts?

Great video, besides the valve cover gasket, is there any other mandatory gasket or seals that I have to replace when putting back the valve cover?

Hello i have bought a 1800w 48v motor recently and am struggling with finding a good battery i dont have that big of a budget could you please help me find a good motor?

I had a 1991 model, it was fast af

Hey thanks I have the 500mx fabirike bike 565

Love the South Park in the back ground 😂

So hard to find old gems like that in Canada, great video! I learn a lot watching these keep up the good work!