Nice engine, looks like it turned out good in the end… maybe running mid forties. I want one. 👍
@Niekvr826 ай бұрын
Cool set! Shame about the lack of grip
@mr.shadestrains60336 ай бұрын
Very cool 🚂👍
@user-ii3fy8fr5s6 ай бұрын
Vielleicht neue Haftreifen, ein sehr schöner Zug,kommt gut ins Jahr 2024.
@Tuxel6 ай бұрын
Schonmal die Haftreifen an der Lok getauscht? Sieht mir aus als wären die nicht mehr griffig/hart - hatte den Fall auch erst vor kurzem.
@purplebuckelwal26486 ай бұрын
Das dürften noch die ersten Haftreifen sein, die sind sicher komplette durchgehärtet und gehören getauscht 😮
@user-gz5dw9ju5e7 ай бұрын
Łał
@dancaptain2055 Жыл бұрын
Music sucks
@dsciarrino3663 Жыл бұрын
The best money can buy 👌
@dominicksforza34842 жыл бұрын
Lose the "music" the motor is what we want to hear. I never liked the bigger 120, the 99.7 (I think I'm close) classic evinrude 115 ran better IMO, the 120 didn't idle smooth at all compared to the 115, it had a bigger block for more torque but the 115 had enough for my little 17' closed bow cobia runabout. the Mercury tower of power outboard could put both of these away however. I've owned them both so I think I can comment on this. Bottom line is, if it starts and runs while taking you wherever you want to go is all that matters.
@dancaptain2055 Жыл бұрын
Fuck that damn music I said the exact same fucken thing
@stijepozupa51502 жыл бұрын
What size of wrench is to unfasten diesel injector (14,15,16 or 17mm),thank you.
@mike_crank2 жыл бұрын
You have to use 17mm size wrench
@andymadden68482 жыл бұрын
hi how much did the parts cost; well done BTW
@77eagleeyes3 жыл бұрын
I have same engine. Is it worth keeping
@helmutfuchs50713 жыл бұрын
U-Pumpe kann aber auch ohne Klappern hinüber sein, Membran undicht, dann ist Öl im Schlauch wo nur Luft sein sollte.
@jeremyillingworth43024 жыл бұрын
i have the same engine compression is 85 in 2 cyl and 95 in the other 2 cyl is that ok? and what did it come with brand new?
@tylerthomas37443 жыл бұрын
I have a 1993 Johnson 120 looper. Compression is 130psi all cylinders
@rchede4 жыл бұрын
Great job what slack are you using between pistons and cylinder? Wiseco is forged the clearance is different from the original? I'm refurbishing my engine I really like it 120, I'm wanting to use boyesen picks, did you get any positive results? Tks
@ct17624 жыл бұрын
Folks DO NOT use Wiseco's. I've rebuilt 3 crossflows and one looper and ALL seized or got badly scored. I use the OEM pistons or the coated sea-pros now and not a single problem. I'm guessing these are forged, and swell up alot more than the stock cast ones. great for racing though. How is the motor doing with these?
@purplebuckelwal26482 жыл бұрын
Until Now, the engine works fine :-)
@GreggAdventure4 жыл бұрын
Appreciate the sharp highrez looks at the motor. Helped me compare some wiring, as I'm a months deep, trying to get my motor to start. Add keywords to this video. Should have way more hits!
@Darkecto15 жыл бұрын
Hi, sauberer Motorlauf. Hast du die Düsen neu gemacht, oder sind die original?
@adamstanisz56495 жыл бұрын
Did you have low compression in that cylinder?
@Caminadawerft_Schweiz6 жыл бұрын
🤘
@SW-mg7et6 жыл бұрын
I have the same thing coming. Do you have any idea where to get workshop manual & dpare part list? Was the piston manufactured from order? Thanks for the help, neat build!
@purplebuckelwal26486 жыл бұрын
Hello, I got the part list from epc.brp.com/ , the piston was not build from order, it was an "standart" oversize piston +0.10. As an example, you can have a look at www.maxrules.com for rebuild kits, so did I. Good luck with your rebuild.