Will this do epb service mode for 2023 nisssan pathfinder ?

what did your car sound like before replacing this

Did you have to go to the dealer to get the Mercedes brand wiper blades

I had the same problem. Very very helpful. Fixed it right away which no one was able to figure out. Thank you.

😊

Where and how much cost of the new door lock ??

I need a diagram that shows how to replace all 8 transmission solenoid s in limbo these are for a2006 Nissan maxima 3.5sl

And one other thing. From what i can tell from anylising the gears in the transfer case, it would seem that the large gear in there has a way to drag fresh oil from the bottom of the case up to that upper chamber by way of a channel in the case housing metal. And there is a entrance hole up top where the path leads to. And that hole goes into that separate chamber where the clutch disc sits. Cuz i always wondered how any fresh fluid gets up into that chamber. Cuz its a small chamber. So it wouldnt surprise me if all your shudder went away just by only using that lower fill plug. Cuz there is no way in hell to access that upper level 3rd fill hole unless you detach the drive shaft and flex disc. So much simpler doing it by way of lower fill hole.

Mercedes the company, not the dealer, recommends trying the fluid change to fix the shudder. And says that if it doesnt work then dealer is to put in a whole new transfer case 🤔. Quite a huge dichotomy in those two bits of advice. That weird advice alone should have one scratching their head in wonder as to what isnt mercedes really telling us. The shudder actually comes from the upper chamber ontop of the transfer case. Youll see a different fill plug way up at the top. But drive shaft has to be removed and it will slide back into the back half of the drive shaft so as to give room. Inside that chamber up top is a single clutch type disc that looks like a slightly small version of a CD music disc. Its sandwiched between two spring loaded pressure plates with a set of planetary gears up in there. Theres a vertical cover there that also can be removed and the whole planetary gears and disc can come out. But no need to do all that nonsense. When fluid gets REAL old that disc doesnt slide so well anymore and thus the "shudder". But just like you said, what people dont know and what mercedes doesnt explain that after you put in fresh fluid, it takes a really long time for the new fluid to work its way in between that disc and front/back pressure plate surface. Ive done the job 3 times. And i can tell you, at least a full week of driving and maybe more. Plus doing some slow 360's can help speed up the procees. I had very bad shudder and at first the 360's would make it go away for about a minute. Then it would come back. That gave me hope. But gotta hang in there cuz after a full week of driving with hideous shudder it all went away and hasnt been back in years. Reason i had to do the job more than once was because i clipped a curb hard once while making a turn and i think that kinda stopped the rear wheel for a split second and as i continued to drive i had that shudder back. I believe it made the transfer case clutch disc jump a bit causing a dry spot on it. But looking back i realize i didnt need to redoo the fluid again. All i had to do is keep driving for the week till that already new fluid worked itself back into that dry spot. Well hope this helps someone out there.

Hello, I’m getting p0746 and p1778 on my Nissan nv200 This error code related to pressure controls solenoid that is part of valve body so I want to replace the whole thing Thank you for your video May I ask where did you order the part for your car ? I’ve checked with the dealer and they want around $1400 just for body valve

Thank you 🙏

I don't understand if you now the pressure is drop why change injector but over all it help me

A lot better then spray in honestly

man, why was everything else changed before checking pump pressure? That an amateur move

2024. Worked for me. I’m 39 years old. It was not able to stay up, especially in colder conditions such as you stated. I first tried a GMCialis pill right into the fuel tank about 30 minutes before I was ready to make it raise. It worked at first but I eventually had to just had to break out the screwdriver and do some re-strutting 😂

so if my windows stuck down can i take off the door panel, pull the pin and then raise the window and replace the pin to keep it up?

Thanks "YCG"

Awesomely done

I just did the head on mine. Ran fine until my way home from work not long ago. It’s been running great for a week. Now it’s not missing when it’s cold but once it warms up, has a slight miss but I can accelerate out of it. Only does it when it’s warmed up tho. Was thinking I missed some carbon buildup and it’s created some bad detonation, possibly the catalyst is messed up?

Man, I just watched this video and swapped plugs n wires on my 01 outback. It drove perfectly after swapping them out. I came back to my car a couple hours later to go get some food and now it’s sputtering in park (which it only sputtered going from neutral to 1st gear) and won’t get up to speed. Again, it was driving perfect after swapping it all. PLZ SEND HELP I HAVE WORK TOMORROW 😭

Does anyone know what kind of troubleshooting would be available for a situation where the display cannot go into the active learning mode and instead stays on the screen with the check mark?

thank you very much. was looking everywhere for a simple video for nissan rogue and this is basically the same. U da man!

you skipped over the most important part of the installation. you didn't show how you twisted the injectors into the rail. this is the hardest part. many replacement injectors o-rings do not fit correctly.

Great video!

What's the torque spec for tightening the new valve?

Hey how's it going i was wondering if this radiator is the same part for 07 530i (e60) .. im doing some research and im getting two different radiators ...

Hello sir I really appreciate this video one question is this valve body same as a 2010 Nissan Altima?? Let me know asap please and Thankyou.🙏🏿

Hello your car guy. I see this was like your newest post; i saw a post from 5years ago for code p0171 i belive on a toyota camry. i have a question about a subaru outback; its an 08 2.5 sohc . im trying to fix a 1153 code an random 0171 code. i have a new maf on it an 02 sensors have sprayed the intake for leaks. none just wondered if you have delt with it before on an subaru an could point me in a differant direction. thanks randy

Thank you, used this as a guide to do this on my 2005 Sienna after getting a used replacement off of eBay.

This video has helped me twice in the past 6 years. Thank you for making this video!

Hello. Thank you. My front panel is light off then AC intermittent. Relay is ok. But odometer reset control is not working. Do you think I should take my car to dealer to checkup the control panel?

Thanks dog❤

Great Video. Thanks for sharing

THE BATTERY DOES NOT LAST LONG AT ALL. YOU MUST BE A SALESMAN FOR FOXWELL.

I just got my truck back earlier today. I guess my dealer's parts/mechanic person has never seen or been given instruction on installing the liner. When I picked it up I told them my liner was not installed correctly. The person that did the install argued saying it was and the tabs would not and were not meant to fit underneath on each corner. I insisted that he was wrong. I got no where with him and told him to go watch a youtube video. I needed my truck and said I would be back when time permitted for it to be done correctly.

5 years later i found yr video. May i ask y a question with a ac issue. I have a honda 2008 mk8 1.8. I filled the ac up with coulant. I replacement the relay I can hear the ac pomp working. I checked the same wire. I have 1 connection instead of 3, it works. The H intake feels cold but the L intake feels warm. Still the air isnt cool inside the car. What could be the problemen?

Thank you brother you just saved me with this video i had one broke on me in my jeep thank you thank you

Ok im having a issue... my inner brake metal clip goes on top instead on the bottom it was installed this way when I try and turn it upside down to have the clip on the bottom it doesn't sit right do you think maybe they got the back brakes mixed up on both sides

Going to get them but I don’t see the resisters in the set

German engineering on those rivets 😉

How much was that??

Is this the flex limited

Quite helpful.

just spent ages trying to sort out why roof wouldn't shut, even tried winding the roof manually, the key to the problem was how to reset motors which after watching your easy to follow video & a bit of trial & error, I managed to close roof. Saved me from covering over car & taking it to the garage next day. Big thanks

Can you also use the torque app using this thinkdiag system in your in car Android system

I got a p0744 on my nissan juke and im going to be doing this to see if itbqill get rid of the code

I've got a 2011 GMC Yukon Denali and there is no "Press ✓ to relearn key option"

Nice video! Curious, did you have to relearn the tcm/trans or relearn the gear ratio?

Saved my life brother. Replaced spark plugs in a 1989 Jaguar Vanden Plas. Used a torque wrench to tighten but for some reason one of the spark plugs broke. You can imagine how I felt! Did a search, found your video, picked up the ez-out at Lowes for $10.00. Extracted and replaced the spark plug today. Holy sweet Jesus am I relieved!! Than you for posting this.

The wire that clips to the bracket where does that go I rip it out by accident