JC Automotive

Пікірлер

@yen1691 5 күн бұрын

nice hood nice bumper amigo😅 what happen?

@JCAUTOMOTIVE4444 4 күн бұрын

🤣 I was running late to work. Went to grab my phone and when I looked up, the traffic came to a stop on the freeway. I braked hard but it was too late. I hit the hitch on a work van. Absolutely nothing happened to the van but my car took a lot of damage. The guy told me I could take off and he wasn’t gonna report it. At that same moment a highway patrol pulled over and gave me a citation for driving too close.

@dylanwilliams3807 17 күн бұрын

I have a 2003 eu3 civic hatch. After not getting used much for a few months its started idling at 1500-2000rpm. Will sometimes drop back down to around 1000rpm then surge back up to 2000. Do you think its likely pulling this of and cleaning it might fix it? It happened briefly a few years ago but went away after a bit of an "italian tune up". Not getting any CEL.

@AL.B.Fineee 26 күн бұрын

Nice work my friend, thanks for the tips 🤙🏽😎

@LungeloMkhabela-d3f Ай бұрын

Diagnosed soccert

@wandaimourino6971 Ай бұрын

Change oil

@rexbey777 Ай бұрын

Good video

@hectorjoydiaz425 Ай бұрын

Thank you!!

@madmarc2001 Ай бұрын

What kind of air compressor do you recommend for home use amazon under $100 ? Thanks

@catalinvulcu8217 Ай бұрын

Hi I like wat you do. Super job you down 👍

@SLPSRocks 2 ай бұрын

Im surprised not a single person on the comments has complained about how stupidly Honda designed this car lol

@shepherdsfleetservicesllc8147 2 ай бұрын

Alien space saver

@DanielAntonioCorderoAngulo 2 ай бұрын

Muchas gracias aprecio lo que haces

@ALfa_Channel365 3 ай бұрын

2024 and i went to get a price for this same 2012 Nissan Sentra at a shop and it was apprx 450 🙄 I do not have air tools and wonder if its possible to do all of this without air tools ? I just have breaker bars, sockets and wrenches..

@JCAUTOMOTIVE4444 2 ай бұрын

Very possible. Just takes more time is all

@rhijel5 3 ай бұрын

Good job my guy🤙🏽 very entertaining

@michaelsaim3725 3 ай бұрын

My H.C 2003 side card is burnt can u help me with a new one?

@itzmxlvin 3 ай бұрын

Thanks for the video man was able to take my cylinder head off shop quoted me 4K for gasket replacement

@ezgaming5218 3 ай бұрын

I loosened the 3 bolts on the left mount and my new rear mount is still sitting a little too high so I can shove the bolt in…

@Justin-l3t3x 3 ай бұрын

great tutorial!! keep em comming.

@CesarOmarMartínezchavez 3 ай бұрын

Thanks a lot my friend I still have my Civic 2003 coupe and your video was very useful The job is done and everything looks pretty good Thanks again Best regards from Mexico 🇲🇽

@jose120808 4 ай бұрын

hello. For the Mazda 3. 2021 Is it possible to do this procedure but I don't have the scanner, can I disconnect the fuel pump relay? without fear that it will show a fault code later. Thanks in Advance for your suport!

@tweek857 4 ай бұрын

So i did this job on a 2006 ex 4 door civic. Don't think I'll be doing another one anytime soon. Unless im compensated very well 😂

@JoeFarkas 4 ай бұрын

I know you did this five years ago but do you remember if this was a regular gas engine or a CNG engine. I have a CNG and was wondering if I could do the same for a CNG plug change.

@JCAUTOMOTIVE4444 4 ай бұрын

It was a regular gas one

@JoeFarkas 4 ай бұрын

@JCAUTOMOTIVE4444 Thanks do you know if a CNG is the same as regular gas to replace plugs

@JCAUTOMOTIVE4444 4 ай бұрын

@@JoeFarkas I’m not sure to be honest

@christopherjohn944 4 ай бұрын

What was the torque specs for the crank pulley bolt

@JCAUTOMOTIVE4444 4 ай бұрын

This is what the manual says: Tighten the bolt to 69 N-m (7.0 kgf-m, 51 lbf-ft). If the pulley bolt or crankshaft are new, tighten the bolt to 177 N-m (18.0 kgf-m, 130 lbf-ft), then remove the bolt and tighten it to 69 N-m (7.0 kgf-m, 51 lbf-ft). Then tighten the bolt an additional 90 °.

@djlancer88 4 ай бұрын

so mine has been randomly spit and sputtering at idle and almost dieing, should I look into this or you think its something else?

@JCAUTOMOTIVE4444 4 ай бұрын

If it has a check engine light I would start by seeing what code it is. I don’t think this would help something that runs that bad

@djlancer88 4 ай бұрын

@@JCAUTOMOTIVE4444 No check engine light on but a couple months ago I had to replace the camshaft position sensor, thinking it may be related to that. Thanks man

@JCAUTOMOTIVE4444 4 ай бұрын

That could very well be it.

@christianleon527 4 ай бұрын

Why you remove so many things? I literally just fed the cable through didn’t remove the seats or all the plastics

@JCAUTOMOTIVE4444 4 ай бұрын

Because I wanted it done right

@christianleon527 4 ай бұрын

How is removing 20 extra parts the right way? That cable is just resting In between all the parts you removed. If u lift the seat up you can see the cable and pull it through. I pulled it through the exact same route it was previously routed and reused all the clips. 10 min job. Works great 😊

@JCAUTOMOTIVE4444 4 ай бұрын

@christianleon527 make a video and show us

@christianleon527 4 ай бұрын

@@JCAUTOMOTIVE4444 bro I just thought I would let you know there’s an easier way to do it maybe for your next video but you obviously don’t want to hear it. Ttyl buddy thanks for the video.

@JCAUTOMOTIVE4444 4 ай бұрын

🤣 sorry bro just everything is either negative or positive no in between here on the comments. I thought maybe you were just trying to prove me wrong. I appreciate your feedback. I honestly just do whatever is in the book. I can’t remember what source I used for this video it was a while ago. But thanks again sorry for the misunderstanding

@christopherjohn944 4 ай бұрын

When you removed the head we’re all the valves seated flush , is there supposed to be like four sticking out ?

@JCAUTOMOTIVE4444 4 ай бұрын

I believe that’s normal. If the cam the rockers are still installed they won’t be flush

@christopherjohn944 5 ай бұрын

Did the electric impact work to take off that crank bolt and what kind of man of impact is that ?

@JCAUTOMOTIVE4444 5 ай бұрын

It did it is a kobalt brand. The secret is the socket I used a.co/d/5IOTHjv

@christopherjohn944 4 ай бұрын

@@JCAUTOMOTIVE4444thanks , also what kind of socket did you use to remove head bolts ?

@id1763 5 ай бұрын

I noticed my new radiator came with the ac condenser (oem). Any special tips on the this? I noticed the radiator came with ND Oil 8 fluid? I think it’s for the ac compressor pump? If I replace the ac condenser too is that another long chain of steps or?

@JCAUTOMOTIVE4444 4 ай бұрын

Meant to reply sooner. Yea ND oil is AC compressor oil. The condenser is very easy to get to if you have the radiator out already

@stevegarmier563 5 ай бұрын

Great video. Wish all mechanics on KZbin would just get to the point instead of talking for 15 min.

@jasonmallory7183 5 ай бұрын

I am getting a code for "TPS circuit A voltage low". Could this be whats causing it to go into limp mode after about 20-30 minutes of driving?

@mercpindi5522 5 ай бұрын

Its a beaten up civic But it wont die until u let it die ..

@jxhkb 5 ай бұрын

What did you clean everything else with? I know they clean the head when they resurface it but the cylinders, pistons, the chain etc.? Going to start tackling this in the morning with your series. Truly appreciated!

@jxhkb 5 ай бұрын

Just saw you used a new timing chain

@JCAUTOMOTIVE4444 5 ай бұрын

Used a carb cleaner on top of pistons. Careful not to get the cylinder walls. As far as everything else I didn’t clean it other than oil change. I used assembly line on the cam lobs, anywhere there’s contact points but I did prime the engine before starting it. That’s very important to do.

@jxhkb 5 ай бұрын

@@JCAUTOMOTIVE4444 thank you for the heads up. I recently got it done by someone 3 months ago and it’s bad again. I can’t get the timing cover off to save my life. I’ve taken every bolt and some. May be from all the liquid gasket that was used. Any tips on how to get that out with out damaging it?

@JCAUTOMOTIVE4444 5 ай бұрын

I just know there was an edge I used a small pry tool. Just gotta be careful not to nick it.

@jxhkb 5 ай бұрын

How did you prime the engine?

@andyroid5028 5 ай бұрын

Great video. Thanks man. I just wanted to add this: if, by chance, the alternator or any of the pulleys need changing, it's SO much easier with radiator being out of the van. So, do those repairs at the same time of radiator replacement, if it is feasible. BTW: just being honest... not a fan of background music, but at least you decrease the volume when you are speaking. 👍😊

@JCAUTOMOTIVE4444 5 ай бұрын

Old video I no longer use music. This guy was very cheap and just wanted the most basic cheap repair as possible so doubt he would have wanted more done

@Blade-hp9mn 5 ай бұрын

Great video, how many cans did you use?

@JCAUTOMOTIVE4444 5 ай бұрын

I believe about 2 1/2

@j_rainsgoat3929 5 ай бұрын

My express van seems to have a restriction in the ac system. Cools good when moving. Then cycles on and off of high pressure when idle or after restarting. Wondering where

@PeaceNinja007 5 ай бұрын

When installing the new sensors, do they need to be torqued to a specific rating?

@JCAUTOMOTIVE4444 5 ай бұрын

33 LB FT for this specific one

@alangorski9230 6 ай бұрын

2016 Mazda 6, P0171 code. Might this process help with this? I do feel the car sputtering just a little when not moving and in gear.

@JCAUTOMOTIVE4444 6 ай бұрын

It could but if it’s sputtering already then it might be too late. You could try. I have an Acura that is also direct injection and i physically took the injectors out and had to clean them but they worked well after

@alangorski9230 5 ай бұрын

@@JCAUTOMOTIVE4444 Thanks! My thoughts exactly... figure i could clean them and then see if it comes back. Or just replace all 4 and hopefully avoid doing it twice. Thanks for the note back.

@PeaceNinja007 6 ай бұрын

Please 😭 I’ve been trying for hours. You’re the closest thing all over yt. Can you make a video on how to re install the throttle cables back on the little earlobe looking thing?? 🙏

@JCAUTOMOTIVE4444 6 ай бұрын

I don’t have that car anymore……. I’m not sure when I’ll come across another just like it to fix

@PeaceNinja007 6 ай бұрын

@@JCAUTOMOTIVE4444 Its cool I finally got it 😎 Took me hours but I finally got it

@fh3486 6 ай бұрын

God blessed u

@mattbickford2640 6 ай бұрын

Car was above 10% on throttle position sensor and wouldnt let me get out of park, thanks! Works great now that i replaced it! (Anyone have issues with dorman? Idk about their quality since they are so cheap)

@JCAUTOMOTIVE4444 6 ай бұрын

I didn’t make the part. Just the part I had at the time.

@indiomonk123 7 ай бұрын

Great video.. Now we know why these jobs cost so much. I was curious on what it would take to do this job and now I know. Doable but not very easy... Thanks again.

@aaronsanchezz 7 ай бұрын

Can you do this with the injector out of the car? Use a 12v battery to connect to the injector to open it, like the old school injectors?

@JCAUTOMOTIVE4444 7 ай бұрын

I'm trying to think about this question. I'm sure you could. but I'm not sure how well it would work being direct injection. i believe with direct injection it requires over 2000 PSI and that's why the secondary high pressure fuel pump is required. In the past, I've put the Injectors in an ultrasonic cleaner and opened them and it seemed to work. So I believe it could work

@kuldiptoor6822 7 ай бұрын

Thanks for this video

@yeahyeahyeahyeah1111 7 ай бұрын

This is really appreciated man ! Did you just go off the all data diagrams?

@JCAUTOMOTIVE4444 7 ай бұрын

Yea I did.

@chrisfisichella7665 7 ай бұрын

Thank you, that was very thorough.

@mcp08gt 7 ай бұрын

How is it holding up so far. I’m gonna try do this for my 07. Just started to leak from the block.

@JCAUTOMOTIVE4444 7 ай бұрын

Well it held up for 3 years but now the car is long gone. My sister owned it but sold it dirt cheap

@jasoncurry2515 4 ай бұрын

How many miles did you have on it when u discovered the crack

@mcp08gt 4 ай бұрын

@@jasoncurry2515 mine has 172k on it.

@mcp08gt Ай бұрын

@@jasoncurry2515 mine had 172,000 on it when it started leaking from the block

@grahamwolf-bowen3565 7 ай бұрын

Thanks man

@worldpeace5853 7 ай бұрын

I got the cat changed last year for catalytic converter P0420 error on my 2016 CRV. 6 months down the line I got the P0139 error. I changed the downstream sensor this time. 2000 miles more I again got the same P0139 error. I called Denso and they sent me a new sensor because of warranty. I called the mechanic to reinstall the downstream sensor and he says P0139 error may be because of upstream sensor also and recommending to replace upstream sensor. I am so confused this is driving me nuts!!!!!!

@JCAUTOMOTIVE4444 7 ай бұрын

Gotta check for any bad connection or bad wires. Exhaust leaks will cause it also. But I don’t think an upstream sensor would cause that. It would have given you a different code.

@worldpeace5853 7 ай бұрын

@@JCAUTOMOTIVE4444 I got this diagnosed at the dealer and he replaced the downstream sensor. I did ask him if there were any exhaust leaks and he said that wasn’t the case. I think he said 1 year 12000 miles warranty on parts and labor to be honored at any dealer.

@JCAUTOMOTIVE4444 7 ай бұрын

The only true way to tell would be checking voltage. The manual says if your voltage stays between 0.3-0.8V for 2 minutes at 3000 RPM to change out the sensor. I would say get a good brand but denso is good……. My go to brands are Bosch, denso and NTK for 02 sensors. But yea like I said only true way is checking data

@worldpeace5853 7 ай бұрын

@@JCAUTOMOTIVE4444 Makes sense. Thank you!

@sanremodude 7 ай бұрын

I just bought a 2006 Civic with 125k miles on it. The seller told me the engine block leaks. I’m wonder how your fix has been holding up now that it’s been 6 years? My hope is for this to be my kids high school car, so it’s only going to be used around town close to home.

@aaronparker1070 8 ай бұрын

Thanks for making these videos. Quick question; did you sand the block surface, or just clean it up really good?

@JCAUTOMOTIVE4444 7 ай бұрын

It was resurfaced at a machine shop

@AlfonsoValdezjr 8 ай бұрын

For ur first time instructing, you have done a great job. Thanks

Ең жақсы KZbin

Пікірлер