hahhaha, its too loose, you can pull out by only your hand

Nice job, but there is an easier way to do it. Instead of digging a hole in that screw and make a filet through that hole why not just allready using that screw filet and weld an "U" shape (something like that...) steel plate on it with that small crack for the shaft of the motor on that plate, not on the screw. I think my solution it's just easier and I hope I'm going to do something like this sometimes.

Ещё проще: два стула две железных пластины под шестерёнку и дюбелем по оси шестерёнка сама слетает

Идея не плохая,но очень все затянуто

Painful to watch but it works good.

ALGUÉM SABE ME INFORMAR SE A MARCA DESSES TIPO MOTOR JHONSON E BOA?

Hey guys! I see it works with Wide mode, and it works, but the sound icon is turned off so its literally muted the system and it cannot be undone, only if i turn off the demodulator. What causes this?

Вещь!

Yes that’s a drill bit

Great idea, thanks for doing the video.

dump video

A specific guide - thanks

This set up will only decode class 1 clear Tetra DMO. All the EMS Police, Fire and Ambulance use Tetra TMO using the TEA2 encryption algorithm which is extremely secure with all the authentication protocols in place. It is the most secure out of the 4 TEAs.

Столько трудов и все бестолку 😊 попробу снять шестернь от Bosch 10.8 с зазором 1 мм, этот 1 мм от гайки порвет сразу.

This is amazing. The software side alone must have taken forever.

Hiii, do you know if i can upgrade the motor? I was thinking in putting a 540 motor, would it fit?

Hey by any change do you know if the motor of this specific model can be upraded? I have one and was thinking on putting a 540 motor in it? Would it fit?

Hello. I see that it decodes with voice, but with net info I don't get a call ID so I don't hear any voice.

*Awesome!*

Who in the fuck can diy this?!

Man, a plastic gears don't needs a tool to remove the problem is with metal gears

Sir I cannot open page rtl-sdr-ru, page seems offline. Can you upload Tetra plugin somewhere else ? Thank you

Мужик ты супер, быстро, удобно, со всего подручного!!! 👏👍

Dude, how can I be the man when you are the man. I was preparing to slice my wrists and do push-ups in saltwater until I ran across your "so simple it's silly" pinion puller.

Excellence,👏

Thank you very much!

Первое сверление надо делать на сквозь гайки диаметром вала. потом сверление под резьбу.

Проще высверлить с торца винта отверстие по диаметру вала, вставить отрезок вала и свободный конец зашлифовать, что бы потоньше был.по моему так быстрее получится.

Это вообще хорошая тема - мелкий съемник из гайки, особенно если, как у меня, магазин метизов в соседнем доме😀 Я при замене шестерни шуруповерта обошелся паяльной станцией и отверткой, но вот эту идеою вполне можно реализовать на будущее и места он много не занимает.

The best diy I've ever seen, , 👍👍

Задумка то хорошая)) (хотя эта идея не нова). А вот воплощение- это что то с чем то.... Для начала все же надо было тиски прикрутить..

I really do not know but.... i am still waiting for real scanner for tetra and other digetal radio to bay......

Subscribed good 👍 I have tamtech buggy

Can you tell me the ballpark total cost to set this up the exact same way you have it set up. Cheers for now.

Thank you for the video!!! I just made one and it works GREAT!!!! 👍

Thanks for this... But I ended up drilling and welding a No. 8 nut on top instead of making the threads

I like diy stuffs like this. The bore sighters i got are pretty accurate, at least the dot stays where it should be. I attached the bore sighter on my other airgun's barrel using 3d printed clamps, the offset distance between laser dot and bore is less than 20mm. Now I'm gonna do the same on crosman 1322, i can't use any clamp but your paper clip idea inspired me. Thanks!

Is it possible to listen something with this in sweden?

Haw can i get ahold of you in regards to setting up this exact same thing foe someone. Whatever fees are involved of course will be taken care of. If your interested in taking on the project.

good evening sir i tried this solution but it no demodulator block is appearing after adding the magic line into the plugins.xml pls help regards

I've got some of those laser diodes somewhere. I've got a weekend project now!

this is very inspiring me, thank you

True Amateur can you sad how to solve the problem when i want to turn the demodulator why is muted.pls help

Nice mod sir ! But does this esc handle 8,4v with the lipos ?

rubbish !

Class mate nice one

Show 👋👋👋

Take my money, send amazing tool. 🙋🏻‍♀️

Great job But in the cordless screw driver like makita or Dewalt the space between gear bottom and the motor are less than 1 mm can u please guide to to remove it ?I made one like yours but due to thickness its bend immediately

I freakin' love this! Do you sell these? I would love to make one myself but am currently awaiting hand surgery and lacking the dexterity. Things like this are functional fits of art. I love to support those creative individuals over greedy faceless corporations.