DIY - Turn your screw nut to a mini pinion gear puller

[@MWard-zk4wg]

Dude, how can I be the man when you are the man. I was preparing to slice my wrists and do push-ups in saltwater until I ran across your "so simple it's silly" pinion puller.

[@johanrynjah8241]

Reading your comments I almost fell of my chair. . 🤣 😂.. 🤣 😂.. 🤣 😂.. thank you for making my day . .

[@hengkydiandra-8619]

The best diy I've ever seen, , 👍👍

[@TechsScience]

Man, a plastic gears don't needs a tool to remove the problem is with metal gears

[@maxwellrhodes1]

Thank you for the video!!! I just made one and it works GREAT!!!! 👍

[@bubblegum1792]

Great job But in the cordless screw driver like makita or Dewalt the space between gear bottom and the motor are less than 1 mm can u please guide to to remove it ?I made one like yours but due to thickness its bend immediately

[@BobSimpkin]

Great idea, thanks for doing the video.

[@vladimirmorozov1891]

Мужик ты супер, быстро, удобно, со всего подручного!!! 👏👍

[@alexs4963]

Первое сверление надо делать на сквозь гайки диаметром вала. потом сверление под резьбу.

[@suparnohardisetiawan6163]

this is very inspiring me, thank you

[@jozefnovak7750]

Thank you very much!

[@Pug206-wc2uz]

ALGUÉM SABE ME INFORMAR SE A MARCA DESSES TIPO MOTOR JHONSON E BOA?

[@sncat]

Столько трудов и все бестолку 😊 попробу снять шестернь от Bosch 10.8 с зазором 1 мм, этот 1 мм от гайки порвет сразу.

[@ТомСойер-п6м]

Проще высверлить с торца винта отверстие по диаметру вала, вставить отрезок вала и свободный конец зашлифовать, что бы потоньше был.по моему так быстрее получится.

[@Qolloskey]

Thanks for this... But I ended up drilling and welding a No. 8 nut on top instead of making the threads

[@j.bivens8127]

I freakin' love this! Do you sell these? I would love to make one myself but am currently awaiting hand surgery and lacking the dexterity. Things like this are functional fits of art. I love to support those creative individuals over greedy faceless corporations.

[@goovernick2045]

Это вообще хорошая тема - мелкий съемник из гайки, особенно если, как у меня, магазин метизов в соседнем доме😀 Я при замене шестерни шуруповерта обошелся паяльной станцией и отверткой, но вот эту идеою вполне можно реализовать на будущее и места он много не занимает.

[@nevermind-wp3bf]

Nice job, but there is an easier way to do it. Instead of digging a hole in that screw and make a filet through that hole why not just allready using that screw filet and weld an "U" shape (something like that...) steel plate on it with that small crack for the shaft of the motor on that plate, not on the screw. I think my solution it's just easier and I hope I'm going to do something like this sometimes.

[@JodBronson]

*Awesome!*

[@Tavpanda]

Take my money, send amazing tool. 🙋🏻‍♀️

[@LS17EAGLE]

Class mate nice one

[@buckdangt3343]

Yes that’s a drill bit

[@seniorzasader4328]

can youi sell this to me

[@trueamateur5554]

@senior zasader If you need it, I would give it to you and you just have to pay the shipping. Let me know you address and I can ask for how much shipping cost.

[@chriscox52282]

@@trueamateur5554 what a good guy! Respect.

[@stanisawmuszynski8978]

Excellence,👏

[@polyglot5052]

Ещё проще: два стула две железных пластины под шестерёнку и дюбелем по оси шестерёнка сама слетает

[@НовикВалерий]

Идея не плохая,но очень все затянуто

[@Crozbyguy-rg1iu]

Painful to watch but it works good.

[@amaurif8777]

Show 👋👋👋

[@mumis089]

Вещь!

[@digisolutiondaraz6660]

hahhaha, its too loose, you can pull out by only your hand

[@Nat12360]

Задумка то хорошая)) (хотя эта идея не нова). А вот воплощение- это что то с чем то.... Для начала все же надо было тиски прикрутить..