STRATTEC Security

Пікірлер

@alberts7061 12 күн бұрын

Thank you so much. Very very clear instructions.

@Fytox2 2 ай бұрын

You saved my bacon with this video, thanks for the upload

@cw420951 2 ай бұрын

Now make a video on how to put the cylinder into the ignition housing

@benjasvargas8564 7 ай бұрын

Thank you So much for the video you the best

@MrDani3lantunez 10 ай бұрын

When I went to turn key for it to lock in it kept spinning , someone broke into my truck and all they did was damage this part. Struggled to open door that was stuck shut for this not lock in place. For $129 dealer price not ideal for me but your vid helped will go tomorrow see if they can swap part out

@thegonz7833 10 ай бұрын

Strattec 7024124 GM Ignition Lock..2016 sierra bought new,135k,pulled into rest stop,got back in,key would not start to go in.F'd with it,finally took oil from dipstick onto key,got it to go in,giggled until it turned.Giggling would get it to turn ordered part next day.No warning fail.How about you,quick fail? miles?

@thegonz7833 10 ай бұрын

This vid helped 100% i did have to tap the collar sleeve on.with nothing in the cly it would not slide on.All seems good but dont like the force needed compared to this dude sliding it on. Strattec 7024124 GM Ignition Lock

@houstonlocksmith-tx Жыл бұрын

Do the odd numbered wafers go in "upside down" compared to the even numbered wafers?

@CarlosFlores-zv5pv Жыл бұрын

Tnx for your time and knowledge very well explained video and audio are perfect tnx

@mattB-uy9bf Жыл бұрын

Just the video i was looking for. The instructions in the pack dont give the correct tumbler postions.

@bpdobson1 Жыл бұрын

so where is the video showing how to use the software?

@jacobgoodwin7491 Жыл бұрын

Very helpful! Had an issue with a 2016 GMC Sierra, I was taking the ignition tumbler out to replace the ignition switch and didn’t realize the front most shaft got stuck in there. Used your video to figure out how to put the locking tabs in with the spring. Thank you for detailed video!!

@jonnysanchez985 Жыл бұрын

How’d u get the shaft out

@josephjennings9246 Жыл бұрын

So what’s the cuts

@felixcordova4282 2 жыл бұрын

Is there a video on how to disassemble after coding ?

@felixcordova4282 2 жыл бұрын

Is there a video about how to disassemble the ignition after coding

@DIYeverything513 2 жыл бұрын

Awesome video very very clear and helpful.

@shakilshaikh4102 2 жыл бұрын

how tumbler remove from barrel

@dtnel 2 жыл бұрын

You forgot to answer your phone vibrating around the 5:00 mark…. 😂🤣😂🤣

@Mohammed-og5pp 2 жыл бұрын

The 2qq1out

@tinhtran1309 3 жыл бұрын

I try for my truck but can not put in?please help me

@Middle_American 3 жыл бұрын

Thank you for this video. I was able to use this video for guidance to change the cylinder on a 2014 Silverado.

@bradhartsoe9128 4 жыл бұрын

How do you remove the cylinder from the ignition Lock Housing if the key will not turn?

@renedelrio8042 4 жыл бұрын

Great video as I am in the process of replacing one, and I got stuck with missing the step with the retainer. Hopefully I can try this again tomorrow and get this vehicle on the road again.