What in the world is that annoying noise? Great video but the music was distracting and made it hard to hear what you were saying. I was able to accomplish this task thanks to your video.
@Eric-zq3vlАй бұрын
Glad it worked out man thanks for posting this
@Memphis_TalkALot901Ай бұрын
Thanks everyone thanks
@Memphis_TalkALot901Ай бұрын
So this exactly why my 2010 jeep gr ch in limo mode smh so glad I finally picked up on this because I’ve been goin through hell literally > it’s reading a u0111 u0121 code couple more u codes and after finding out once I looked down at my back rotor it’s really bad so it’s coming together now lol wow just was fina junk the thing smh few mechanics say a wiring problem dk
@brosolutionspАй бұрын
You almost get to 1000 subs bro keep it up! New sub
@victorr2710Ай бұрын
@@brosolutionsp thank you 😊
@Poppadee78Ай бұрын
Hey man, I just wanted to say thank you for putting this video out there. After traditional troubleshooting methods failed I followed your video step-by-step. Only to realize I had the same exact issue with my vacuum distributor plate. It wasn’t burnt but it was missing a little bit of material. I put a gob of liquid electrical tape where the material was missing, put it back together and boom!!! just like that it’s working 100%. Thanks man.
@victorr2710Ай бұрын
@@Poppadee78 glad I could help! I love to diagnose issues down to the exact problem
@Poppadee78Ай бұрын
@@victorr2710 when I assembled it, the control was set to max AC. Question. Would I damage my repair if I spun the dial to the off position or any other setting? When I assembled everything, it was already set to max AC and I’m afraid to mess with it again.
@mathias05842 ай бұрын
I have engine code P2562 on my 2016 Hyundai Santa Fe Sport 2.0T. Turbocharger Boost Control Position Sensor Circuit. This error code indicates the PCM detected Turbocharger/Supercharger control A circuit signal was not within acceptable limits. Is what it says on the sheet when I went to go get my engine code scanned. Is this error code covered under extended warranty?
@luxhhq13803 ай бұрын
Do not need to do all that just be a man and drop the exhaust you got unlimited room after that and it’s 100x easier
@victorr27103 ай бұрын
There's no need to insult me because you're miserable. Have a nice day and be a better person. Everyone can do it how they want to. This is just the way i wanted to do it and it worked.
@Joker12The3 ай бұрын
Extremely helpful thank you
@philwertz13 ай бұрын
Tried this out...mine was burnt on same spot so I put a dab of caulk, wish I had silicone but didn't. Anyway, put it together and it worked. I used a toothpick to shape the caulk into what I hoped would seal right there, let it dry and put together. I don't think I will use that knob being that the seal probably won't last long. Thanks for the idea. I just didn't feel like buying another part.
@victorr27103 ай бұрын
Good job saving money!
@jazhiel5164 ай бұрын
My car brought up that same code just started revving while on the gas on any gear. Car doesn’t accelerate at all in any gear just revs. Is this a similar issue or something bigger?
@JohnBotero-e1o4 ай бұрын
Snap on, overpriced garbage . Couldn't even give you the right trouble code. I have an Xtool d7, fully bidirectional and works like a dream and cost me a fraction of snap on. In fact, it also has software for fully electric vehicles. I knew it was an external transmission pressure sensor, typical problem with hondas, not necessarily a serious transmission issue. Causes: 1- severe dirty transs fluid and filter, 2- transs sensor failed.
@ImpactSoundSystem15 ай бұрын
Great information!!
@Gbodyteggy12085 ай бұрын
The throttle body you gotta not move it that way jst use brush on next task or it will mess up teeths inside the throttle body but i need 2 replace my gaskets 2
@bpleunik6 ай бұрын
Thank you!
@mikebarbee22177 ай бұрын
I have a BIZARRE issue on the 98 Durango I bought a few weeks ago. With the blower set on heat or vent, when i accelerate a little hard, the blower always switches up to defrost. When i let off the gas back to normal acceleration, its switches back down to vent or floor heat that its set on. It happens every time. How weird is that???
@victorr27103 ай бұрын
Vacuum leak
@sweetiepienumber17 ай бұрын
I'll need to remove the glove compartment... I would need to rig something with a thinner probe on my tester; tape or shrink tube and wire? My bet $ is just to replace the resister. Thank you for taking the time to share.
@MarkS-xh7mr8 ай бұрын
I have a question my 08 edge is misfiring still p0303 an i also have a p0171 ive already swapped the plug out an changed the coil but still misfiring in the same cylinder i dont have a scan tool an was thinking about replacing the fuel injector for the 60 dollars should i do that or just bring it to a technician ?
@victorr27108 ай бұрын
Depends on your skill level. Changing the fuel injector is a little tricky but if you feel confident then try it yourself
@Muffduster9 ай бұрын
I replaced both the unit bearings AND the wheel speed sensor. Still getting C101F and U140A. Oh well.
@malikal-ghafri93872 ай бұрын
I have same issue 😔
@NoahPARK829 ай бұрын
it was really hard to remove that lower bjoint from the shackle it took me a while
@Amouurdior9 ай бұрын
This is a awesome video and it worked i jus took engine light off my 2007 infiniti G35
@victorr27109 ай бұрын
Happy to help
@momofaro9 ай бұрын
Is there coolant in the hoses when you remove them? I'm curious if they have to be capped off as you've shown. Thanks for a great tip, it makes it much easier to fit the intake air distributor with the lower fuel rail.
@victorr27109 ай бұрын
Even if you drain the radiator, there will be coolant in the hoses. I capped them off to keep everything clean
@ericmacdonald33659 ай бұрын
What size are the 3 bolts?
@ayoubhassan96489 ай бұрын
What are the two sensor you have replaced ??
@JohnHighmerSmith10 ай бұрын
Thanks Vick!!
@renro810 ай бұрын
Thank you so much for the video. Car was idling high after replacing leaking valve cover gaskets .Followed along while you were doing the steps and presto it worked.
@victorr271010 ай бұрын
Good job .. glad to help out
@jamie_smile10 ай бұрын
So this is happening to me and it’ll randomly happen while I’m driving down the highway or road. If I’m going over 3rpxmin the car will start shaking until I pull over to turn it back on or off again. It’s been happening for a while and I’m starting to get tired of it.
@victorr271010 ай бұрын
Replace the parts on my video
@frankmiranda135210 ай бұрын
What if the spring is missing ? Could that cause this issue alone
@wendellgreenidge336210 ай бұрын
How did you get the starter out?
@victorr271010 ай бұрын
Remove the front driveshaft and heatshield to get the starter out
@wendellgreenidge336210 ай бұрын
@@victorr2710 and there is enough room?
@victorr271010 ай бұрын
@@wendellgreenidge3362 yup
@wendellgreenidge336210 ай бұрын
@@victorr2710 nice
@wendellgreenidge336210 ай бұрын
@@victorr2710 so why do they say remove the exhaust?
@sabinochavira824311 ай бұрын
I have a 2000 Dakota with the same problem, no air from the front vents only from the defrost, do you think is the same problem vents distribution switch ? Thank you.
@victorr27103 ай бұрын
Yeah
@naptown420011 ай бұрын
Nice work bub 👍🏽. Hey i got a P0204 cylinder 4 injector control circuit,05 cadillac cts i don't have a clue where to start
@lfv9010 Жыл бұрын
My 2007 Ford Explorer is giving a a P0203 P0303 and P0171 code. Should it be driven to the shop or towed....?
@victorr2710 Жыл бұрын
Tow it
@TheHortond Жыл бұрын
I had the same problem. You fixed it the same way I would have. My e brake spun around and piled on one another and rested right on top of the sensor and tone ring. All the hardware was missing from the e brake side and the cable was snapped. I just left it all off and put it back on until I can fix it. I replaced all that I could with new sensor but the brakes dented and ruined the tone ring so now that needs replaced. Same wheel too. Now I have to do the same thing you are doing to fix it. Hopefully it goes as smooth.
@victorr2710 Жыл бұрын
I have faith you'll get it done correctly
@d.l.horton425410 ай бұрын
@@victorr2710 I replaced both hubs for both sides. Now it leaks a little on the passenger side. I think I was tired when I got to it. So I might have missed something. But it runs fine now. If you have a scanner you can watch the signals coming from all 4 speed sensors while driving and from each wheel. The signal for the bad wheel will drop off if its bad and will turn on the ABS light. But you can see not working then when fixed you can see working. Its a great time.
@kitofleury9070 Жыл бұрын
I hv a 2014, h. The same problem, they ask me to change the transmision😮
@fpk1954 Жыл бұрын
🥰👍👍👍👍👍🥰
@Autotruck7213 Жыл бұрын
Didn't work
@victorr2710 Жыл бұрын
You did it wrong
@omentep Жыл бұрын
sill didnt fix my problem and im running out of patience and quick fix videos for this exact issue. ready to put a .44 in the block and sell it for scrap.
@jor-eledgerton1291 Жыл бұрын
thank you for the quote at the end. i needed that.
@victorr2710 Жыл бұрын
Focus on the now. Everything else is not here and now. You're welcome 😊
@devonjones1769 Жыл бұрын
What's the tool called that your using
@eljalizkill0h187 Жыл бұрын
I got a E550 and i got 3 codes i need help p0025 and P0300
@davec.3198 Жыл бұрын
I have the opposite problem. The front works but the rear blows just on high.
@richardrios4760 Жыл бұрын
Wow thank you so much this video saved me a trip to the mechanic. I watched it carefully for the relearn about 4 times before I tried. It worked perfectly..thanks again
@charlievega7597 Жыл бұрын
What was the symptoms that made u replace starter
@solxreaper1gaming797 Жыл бұрын
Your going to mess the gear up in your throttle body your not suppose to mess with the butterfly
@victorr2710 Жыл бұрын
I had no issue after cleaning throttle body. Customer actually appreciated the effort
@erlinraphael8546 Жыл бұрын
Po 017
@speedyd8150 Жыл бұрын
Love the fuckin 70s porn music in the background
@mikec5342 Жыл бұрын
How long would you say it takes to R&R the intake manifold? Gotta tackle my valve cover gasket soon as the spark plug wells are filling with oil.
@victorr2710 Жыл бұрын
It all depends on the tools you have and experience. I'd say 3 or more hours to remove manifold.