Hopefully you can share video for overhauling of exhaust valve.tnx sir.
@Simsimo-zw3poАй бұрын
Thx from morocco
@farshidnoroozi7707Ай бұрын
Thanks for your valuable information and clear explanations. I hope you continue posting more about the WIN GD engine.
@pankilgangta12162 ай бұрын
very helpful
@Carpe_diem3222 ай бұрын
Thank you sir, If you dont mind, could you upload about me-ga engine ??
@Deebak.3 ай бұрын
It's Very useful, Thanks for uploading this video Brother
@SiElect12073 ай бұрын
Sir Does the venting always operate even if the engine is not using SCR?
@ChristenMano-fz5hp3 ай бұрын
Very Good Explanation, Thank You Sir.
@dhanrajgokal9123 ай бұрын
very helpful video! many thanks , safe seas!
@kostisanastasakos14483 ай бұрын
Thank you for the video
@saravanaboopathi58784 ай бұрын
Thank you..
@thisunikahandawa48844 ай бұрын
Thanks a lot for very valuable video and your channel.❤❤
@thisunikahandawa48844 ай бұрын
Thanks a lot for your valuable video.❤❤
@afrazahmad47705 ай бұрын
Very helpful explanation sir!!Thankyou
@ankittewari34285 ай бұрын
Excellent presentation.Thank you
@ankittewari34285 ай бұрын
very helpful.Thank you.
@thurazawwisewish18436 ай бұрын
Thanks
@thurazawwisewish18436 ай бұрын
Thanks
@Arun-lh1jm7 ай бұрын
But where is the draw card
@charliechakraborty89797 ай бұрын
Thank you soo much sir 🙏🙏🙏
@charliechakraborty89797 ай бұрын
Thank you sir. Very detailed video and you explained each step in so detail that I have no further doubt regarding bottom end bearing renewal. Thank you very much sir.
@viplovkapoor81618 ай бұрын
pls throw some light on LDU's Exhaust Ventilation system
@paritoshkumarsingh85488 ай бұрын
Today my doubt cleared regarding urea vs ammonia in SCR
@paritoshkumarsingh85488 ай бұрын
Very informative video sir , please keep doing ❤
@karthiksubramaniyam26659 ай бұрын
Thank u so much for video
@Ahmedba1009 ай бұрын
اهلا اخي انا من الجزائر انا في ورطة هل يمكن التواصل معك
@Indrajeetsingha-kt7iw9 ай бұрын
Many thanks for spreading such wonderful videos. Great effort . I m tsi with fleet. Please contact
@user-ve1lw7qq4p9 ай бұрын
Thanks !
@arushgarg78649 ай бұрын
Thank you so much for the video
@user-ve1lw7qq4p9 ай бұрын
Good job ! Thanks !
@user-ve1lw7qq4p9 ай бұрын
Thanks a lot !
@devershee9 ай бұрын
is 150 bar nitrogen bottle 40 ltr unitor enough for charging accuulators??
@eduardm3579 ай бұрын
Excellent,Thank you.
@danishmomin810210 ай бұрын
❤ thank you for sharing the knowledge
@nadeemsarwar183111 ай бұрын
Very informative video
@babasaikumark42511 ай бұрын
Very nyc content
@ashishmishra214411 ай бұрын
Hi sir. Can you make video please on VIT and Super VIT from basic
@hiiiiivry Жыл бұрын
very helpfull video ...keep it up broo;)
@SunilKumar-he9hy Жыл бұрын
U told the story but not tell why 2 flame dye used
@udayanpaul8042 Жыл бұрын
Never never dismantle the tangential slot cone and the orifice, it will disturb the factory setting, and the incorrect torque of the nut will disturb the atomization pattern, better to only flush the strainer of the atomizer with gasoline or lighter solvent, renew the O-ring every routine, also renew the nozzle every 6 months.
@manojkumarsekar2002 Жыл бұрын
Which manual is this?
@amitkumarchandra162 Жыл бұрын
Great video, thanku so much.
@amitkumarchandra162 Жыл бұрын
great video sir, can u plz add the part where they check the bearing clearance.
@vaibhavnayak626 Жыл бұрын
Excellebt video ..thank you for your efforts!!
@PRASHANT979391 Жыл бұрын
Good to see you man❤️❤️ I was watching the video and thinking this voice sounds familiar😃