Ай бұрын
3 ай бұрын
8 ай бұрын
10 ай бұрын
10 ай бұрын
10 ай бұрын
10 ай бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Пікірлер
@bloodlinefishingadventuresllc Ай бұрын
Nice. Just subbed to the channel. Keep up the great work and tight lines.
@bobowhite11 Ай бұрын
Thank you, started following you also!
@bloodlinefishingadventuresllc Ай бұрын
@@bobowhite11 thank you
@poopandshowa Ай бұрын
How fast does this go with the motor? Trying to decide if I can move up a slower river confidently
@bobowhite11 25 күн бұрын
Around 7 to 8mph
@user-tx6oi3te1x Ай бұрын
Hello
@alexfamie5255 2 ай бұрын
Damn that hurts..I always stick mine down my chest area so I can be hands free. Hope you at least got a nice meal.🎣
@kevinerbs2778 2 ай бұрын
that water will suck the life out of you when it's that cold. Did get through all your layers? I once feel in rocky river whole trout fishing but lucky the coat I was wearing blocked all the water on my upper part. Only my pants got wet.
@69adrummer 2 ай бұрын
recorded in portrait mode...bummer
@bpdp379 Ай бұрын
TikTok will be the death of all amateur cinema…
@TheGraveOutdoors 2 ай бұрын
Hi just wondering your thoughts on durability. How long have you had it and do you think it’s gonna hold up for a long time if taken care of?
@bobowhite11 Ай бұрын
Third year and not 1 issue so far.
@davidrust2504 3 ай бұрын
What’s up with the rubber surgical gloves 😂
@kevinerbs2778 3 ай бұрын
the wind chill will get to your hands that aren't covered.
@alexfamie5255 2 ай бұрын
For sure it's easier to handle the fish
@bobowhite11 Ай бұрын
It was 40 degrees that morning, these still allow my hand to keep the heat in, but still allow me to be able to tie on knots.
@bobowhite11 Ай бұрын
That's a fact,,, it was freezing that day. Most Anglers were calling it early as it was slow fishing. But The gloves made me stay and I ended up with a full limit that day. I just had to move and find them down river a mile or so.
@tyaiex906 3 ай бұрын
wow did you take this video on a flip phone ? why waste the time putting low quality videos on youtube ?
@bobowhite11 Ай бұрын
4K?? Sorry you did not like the quality of the vid. I will try to do better.
@casimirbradley2644 3 ай бұрын
Man absolutely love the setup, you're a impressive dude! I'm thinking about buying this raft. To me it appears to be basically the same raft as the flycraft that sells for over 4k!
@bobowhite11 Ай бұрын
Thank you for the compliment. Third year and have had not 1 issue. From skinny water to Lake Erie she has had many miles under her.
@camdensawicki4005 3 ай бұрын
What shaft length is your Honda outboard?
@bobowhite11 Ай бұрын
Short shaft. Works like a charm, no need for the long shaft.
@sethchristiaens3495 3 ай бұрын
Have you had it out on the water with a third person yet? How did it handle?
@bobowhite11 Ай бұрын
Fantastic!! She motors, and tracks straight while rowing also!
@369motoman 4 ай бұрын
What oars and length do you use, just got the rowing frame for my 13' HD kaboat and looking for recommendations.
@bobowhite11 4 ай бұрын
I use 8 footers. But here is the formula to get the exact length correct the 1st time! Measure the distance between BOTH oar sockets. Divide this # by 2, and then add 2 to this number. This Sum will tell you your ''Inboard Loom Length''. Take this Inboard Loom Length and Multiply it by 25, then Divide this by 7. The Sum will be the ...''Appropriate Oar length'' in inches for your Loom Length.
@369motoman 4 ай бұрын
@@bobowhite11 thanks! I used a similar calculation but came up w 7' and it seemed too short because the raft sits high in the water. I came up w 7.9' and that is more like it 👍
@levimeetz4864 4 ай бұрын
Also wondering how you bent the aluminum and am very interested in the blue prints if you have them
@bobowhite11 4 ай бұрын
I started with PVC Pipe. Heating a 4 foot piece up with a heat gun. Then simply "hand bending" it, while placing it on the boat. After bending it I made the entire aft frame and rack out of PVC. Once I was happy I took it all apart and measured everything including the ANGLE OF THE BEND. IT IS 23.5 DEGREES, AND CAN VERY FROM 22 TO 25 AND WORK FINE. .
@bobowhite11 4 ай бұрын
FYI, the plans and Parts list are up under the "Community Tab" on my page!
@PrettyFlies4aWhiteGuy 6 ай бұрын
What did you use to bend the aluminum?
@bobowhite11 4 ай бұрын
I used a Pipe Bender from Harbor Freight... here www.harborfreight.com/12-ton-hydraulic-pipe-bender-32888.html
@bobowhite11 4 ай бұрын
The corre t angle for the bend is 22 .5 degrees! I mis-printed 13 in a comment, while Meaning to round it to 23 degrees!
@bobowhite11 4 ай бұрын
FYI, the plans and Parts list are up under the "Community Tab" on my page!
@MitchellBowser-tm8pz 6 ай бұрын
Got the same raft this year and plan to add a similar 3rd seat set up so thanks for the video. The raft served me well this summer with lower than usual water here in Mn. Great job, would love to see a clip of it on the water fully loaded though!
@bobowhite11 4 ай бұрын
I will get one up. I had a day in the water with Mans best friend, and she was loving every minute of it.
@bobowhite11 4 ай бұрын
FYI, the plans and Parts list are up under the "Community Tab" on my page!
@bobowhite11 4 ай бұрын
FYI, the plans and Parts list are up under the "Community Tab" on my page!
@user-ly6cl6ou8s 7 ай бұрын
Hey awesome video. I’ve been debating between this raft and a Bris 13’. Have you taken this boat down a river yet? I’m curious how well it handles/ floats with a 3rd person and the extra gear and larger frame. I saw online it’s recommended for 2 people or 650lbs. I don’t plan on taking more than 3 people no matter which raft I choose, but I also don’t want it to be a struggle to row or sit too low in the water when fully loaded. Building a frame and adding accessories will be a winter project for me so trying to get this all sorted out pretty soon so I have something to do! I would greatly appreciate your insight. Seriously great video and amazing work my friend.
@bobowhite11 4 ай бұрын
It Rows and Tracks great, using a Honda 2.3 HP. I have run Class 2 Rapids and Had it out on Lake Erie and Lake Michigan. Fantastic value and great size .
@bobowhite11 4 ай бұрын
FYI, the plans and Parts list are up under the "Community Tab" on my page!
@nickk5577 8 ай бұрын
Is this on the maumee river in Ohio?
@bobowhite11 4 ай бұрын
No Sir this is the Fish Weir on the Little Manistee River is Michigan.
@bobowhite11 8 ай бұрын
The Blue Prints, plus the Supply and Parts lists are up! Click on my Community Tab to see everything! And, please Feel free to ask any questions. Thanks for watching.
@williehauck 9 ай бұрын
🙌 'PromoSM'