That's some quality craftsmanship right there, functional and beautiful

so the overhangs are not really overhangs when it is re orientated?

What are your overhang speeds?

nice work! unfortunately with the cost of living and shipping at a halt in Australia this would cost over $1000.00 to make. I just finished a simple mdf version and that cost just on $100.00 😢 the extraction fan is what's going to be a killer if I buy one and not make one. $100.00+! I'm thinking a 3d printed fan blade on a simple PWM speed controller might have to do.

Take a drink every time he says "uh" or "um" You'll be dead by the end of the video.

Any chance you can link to the extruder knob STL you use in this video?

i found that with my ender 3 pro i can increase the overhang angle to 70 degrees by actually speeding up the printing speeds in the settings by 25%

Clean as he🏒🏒 ! Hope life got better so you can get that video out, i think you'd really get some hits on this insane build 👍🍻

I only need to relevel if I switch out nozzles on my ender 3 version1, but most of the time its still close to spot on because I set it up so the heatbrake butts up tight up against the nozzle and the shoulders of the nozzle rest on the bottom of the heater block so with the same nozzle the hight never changes, but i do check with a strip of paper by 'selecting level corners every once in a while but maybe I'm lucky but my early Ender3 seems to hold zero... but I dont have the stock mainboard I have the MKS with 2130's so maybe the reduction in vibration may have something to do with it...

Sorry if I sound mean but dude fix you z wobble, other than that I loved the video. Keep up the good work

Super fucking annoying gimmicks and shitty audio. Totally overshadowed the content.

Next time you buy one of these ender printers make sure the first bracket that is installed the shorter one with front facing you check to see in it was threaded one I bought it was not lucky I had a kit to do this may have been built during covid lock down in china

Sick! need a how to video for everything in this video!

can u explain the auto leveling software please how it works and maybe a reviewed on it

Just did this mod but white light only...no need for rainbow lighting

i used to be able to print 65 degree over hang but after haveing to changeing hot end now can only print 30 degree can't fix the problem can't finf videos on it and can't get no help on it so if enyone sees this please contact me

No 3 and 5 are not really testing overhang. You just changed the 75 degrees to much less angle. Combos of settings would have been interesting.

my glass bed on neo is a so nasty slippery, i’ve cleaned it as best i can and still can’t print at all unless i use glue stick.

where did you get the inline valve for the ventilation?

why is everybody using external power supply?? there already is light inside cant u grab the power from it?

This is an incredible workspace. Well done.

You have a blue print?

I am new to 3d printing and am trying to calibrate overhangs as it has been messing a few of my prints up. I am confused, while I know that adjusting the orientation CAN fix the issue, why would you adjust the angle for this particular test itself which basically negates the whole point of having the 45+ degrees?

Did you ever release a full video of this build? Cant find it on your channel sadly

PLEASE STOP WITH ALL THE SOUND EFFECTS AND POP UPS

The Ender 3 V2 is garbage and a waste of time

Just Use adaptive layers. Solves almost all problems (and adds just a few new ones ;) )

Where did you get the enclosure?

Love it! Where did you purchase the plexy windows?

You made your own light housing but couldn’t make it to where both circles meet so instead you cut the wire 🤦🏻‍♂️🤦🏻‍♂️ work smarter not harder

Wouldn’t this mess up the LiDAR?

How???

I am finally replacing the extruder on my pros, the arm never broke but the base did. one printer had the brass insert the bowden tube attaches to explode out of the front of the printer mid print. The second printer wore the teeth off the hob gear heh. They lasted a year and a half of heavy use, so they were due to die lol. I am replacing them with some ezr struders I found on clearance.

I don’t know if Elegoo changed their design, but when I setup my magnetic plate I didn’t know anything about the spacer but the print bed appeared to be spring loaded so during calibration it simply adjusted to the new thickness (with the magnetic plate) without any issue.

Nice video thank you

It sounds linke you are standing in a hair dryer

What type of filament did you print this with?

Ive owned my v2 for 48 hours and ive said everything you said at the beginning 😂😂😂

Holy crap! What did you do to get that smooth bottom?

I've been watching a lot of 3D printing videos and this is big far the crappiest video I've watched.

Safe to say these are aluminum extrusion profiles with the necessary parts to attach them together. I like this over a wooden on for my D1 Pro. Gives the option to add extension bed/frame w/o needing to use all new wood framing.

What do people think of the Sprite Pro for the V2?

how do you get all the xtra settings in the cura app

Would love a parts list and source. Also construction instruction. Would Venmo a few bucks for the info. Thanks

Instead of making a hole in which the cable requires modifications to fit through, would it not be easier for user accessibility and ease of installation to replace the hole with a notch and a removable insert to close the gab around the wire? Cut free.

Cheers brutha, this was pretty helpful in terms of direction I needed for upgrades.

Could you make a full video on how you made this

Seems like they need to make a printer that rotates the bed and extruder to accommodate overhangs and bridges and all of that. Kind of surprised this doesn't seem to exist

That's some good stuff

My first video watching you. Just a friendly tip, I watched you talking to yourself! Look at me (the camera iris). That way you are looking at us and so speaking to us.