00-04 Yamaha TTR125 ttr125L TTR Engine Head Valve Clearance Check Adjustment Maintenance

In this video we are checking valve clearance on a Yamaha TTR Dirt Bike.
Fuel Tank: amzn.to/3nL2nGe
Big Bore Kit: amzn.to/2USvKKu
Exhaust Kit: amzn.to/3lQ8tEJ
Carb Kit: amzn.to/3kV6BJt
Engine Oil: amzn.to/3fnOw5A
Also more common repairs with the Yamaha TTR check out:
• Yamaha TTR125 TTR 125 ...
• Chinese Unbranded Knoc...
• Yamaha TTR125 TTR 125 ...
Patreon / midnebraskamotorsports
Instagram / midnebraskamotorsports
Check out our eBay store at stores.ebay.com/midnebraskamotorsports
Shop for parts at: midnebraskamotorsports.com
We Disassemble: Clutch Head Cover Cylinder Piston Stator Points Rotor Magneto Generator Alternator Coil Camshaft Cam Chain Tensioner Rocker Electrical Cases Bottom End Case Set Transmission Shift Drum Fork Gear Shaft Flywheel Starter Idler Clutches Bearings U Joint Yoke Driveshaft Shaft Float Main Jet Bowl Slide Needle Seat Intake and more Assembly
Years: 00 01 02 03 01
2000 2001 2002 2003 2004
Yamaha Dirt Bike ttr125 ttr125l ttr125e ttr125 ttr 125 L E

[@MrClownWorld]

Wow, it’s rare to find a video that cuts to the chase and gets right to the point. Thank you!

[@ISAACP_THEGUTTERGUY]

@@MidNebraskaMotorsports where can i get the feeler gauge.

[@funnybear5]

Great video. I was deciding whether to look at my manual first or KZbin, glad I went with KZbin lol

[@wigman87]

Easy to follow video. Thank you for the making it.

[@bikelife630]

Very well explained! Thanks for posting your video! Very helpful!

[@kylejonesUB]

Great, thanks! Same as an old Triumph.

[@troyhubbard50]

Thank you! I have done everything in the book to the carb on mine and still have popping on decel. Hopefully this helps

[@RedlineFilms54]

Did it work?

[@Bless-edisYeshuaHamashiach]

My ttrs inspection cap is built into engine and there is also no cam gear plate that you can take off

[@nicnadu0515]

Thanks a lot my bikes intake was on about .0015😂

[@dicey616]

Just did a top end on my ttr and now the cam gear doesn’t spin with the crank. How is this possible?

[@racery13]

One word of advice is to clean the engine before opening thus reducing any chances of dirt entering the motor.

[@michaelgranger3874]

Thanks slot

[@aidanfrance1989]

You’d sound like RomanAttwood

[@thescottcentrel7031]

How hard was it for you to get the valve covers off. I've tried everything and cant

[@TheTT124564]

Grab a bras drift and give it a bit of a smack not enough to break it though

[@noel3466]

Will this solve the ticking problem

[@supercooldude824]

Did it?

[@marcsig5352]

i tried doing this as you showed but when i tried finding tdc i found several marks on the fly wheel one is a notch and the other is a black mark which one is correct. can you post a picture of the correct marking in view port ?

[@Jamiel1997]

marc sig kzbin.info/www/bejne/pH2VlIqMpcSKrsk 12:05 - 12:40 is ur answer

[@haydenm.3912]

Do you have to take the engine off the bike to do this?

[@haydenm.3912]

@@MidNebraskaMotorsports Thanks for the response... One more question, I'm unsure where I'm putting the feeler gauge. Am I putting it between the small pin like peice and the thing under it or something different?

[@haydenm.3912]

@@MidNebraskaMotorsports I just went for it and guessed right... Great vid, helped me a lot, bike runs great now

[@tedpaszko8274]

No You can check valves with engine in

[@owl1873]

Seeet. I get it.